Deutsch dropdown-ico

Bedienungsanleitung Sanyo MDF-U7486S

34 Seiten 0.4 mb
Download

Zur Seite of 34

Summary
  • Sanyo MDF-U7486S - page 1

    - 42 - Ultra-Low T emperature Freezer INSTRUCTION MANUAL MDF-U7486S MDF-U7486SC MDF-U5486S MDF-U5486SC MDF-U7486S ...

  • Sanyo MDF-U7486S - page 2

    - 43 - 1 CONTENTS I N T R O D U C T I O N P . 2 PRECAUTIONS FOR SAFE OPERATION P. 3 ENVIRONMENTAL CONDITIONS P. 7 FREEZER COMPONENTS P. 8 Control panel P.10 INSTALLATION SITE P.11 INSTALLATION P.12 START-UP OF UNIT P.13 CHAMBER TEMERATURE SETTING P.14 KEY LOCK FUNCTION P.14 ALARM TEMPERATURE SETTING P.15 SETTING OF ALARM RESUME TIME P.16 REMOTE ALA ...

  • Sanyo MDF-U7486S - page 3

    - 44 - 2 INTRODUCTION  Read this manual caref ully before using the appliance and follow the inst ructions for safety operation.  Sanyo never guarantee any safety if the appliance is used for any objects other than intended use or used by any procedures other than those mentioned in this manual.  Keep this manual in an adequate place to re ...

  • Sanyo MDF-U7486S - page 4

    - 45 - 3 PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with this manual as it contains important safety advice. Items and procedures are described so that you can use this unit correctly and safely. If the precautions advised are followed, this will prevent possible injury to the user and any other person. Precautions are i ...

  • Sanyo MDF-U7486S - page 5

    - 46 - 4 PRECAUTIONS FOR SAFE OPERATION Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to rain water. Only qualified engineers or serv ice personnel should install the unit. The installation by unqualified personnel may cause electric shock o r fire. Install the unit on a sturdy floor and take an a ...

  • Sanyo MDF-U7486S - page 6

    - 47 - 5 PRECAUTIONS FOR SAFE OPERATION Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance. These may be harmful to your health. Never splash water directly onto the unit as this may cause el ectric shock or short ci rcuit. Never put containers with liquid on the unit as this may cause electri ...

  • Sanyo MDF-U7486S - page 7

    - 48 - 6 PRECAUTIONS FOR SAFE OPERATION Use a dedicated po wer source (a dedicated ci rcuit with a breaker) as in dicated on the rating label attached to the unit. A branched circuit may cau se fire resulting from abnormal heating. Connect the po w er supply plug to the po wer source firmly after removing the dust on the plug. A dusty plug or impro ...

  • Sanyo MDF-U7486S - page 8

    - 49 - 7 ENVIRONMENTAL CONDITIONS This equipment is designed to be safe at least under the followi ng conditions (based on the IEC 61010-1):  Indoor use;  Altitude up to 2000 m;  Ambient temperature 5 o C to 40 o C  Maximum relative humidity 80% for temperature up to 31 o C decreasing linearly to 50% relative humidity at 40 o C;  Mai ...

  • Sanyo MDF-U7486S - page 9

    - 50 - 8 FREEZER COMPONENTS Rear side Power cord 12 1 2 5 6 9 (inside) 10 13 4 15 13 (inside) 8 11 7 3 17 18 16 19 14 ...

  • Sanyo MDF-U7486S - page 10

    - 51 - 9 FREEZER COMPONENTS 1. Outer door: To open the outer door, grip the handle. On clo sing, lock the outer door latch completely. 2. Inner door: The operation of the i nner door should be quick to minimize the temperature ri se in chamber. Lock the inner door latch completely when the inner doo r is closed. The inner door is removable for clea ...

  • Sanyo MDF-U7486S - page 11

    - 52 - 10 FREEZER COMPONENTS Control panel 1. Digital temperature indicator: This indicator shows the prese nt chamber temperature or set temperature. 2. Battery check lamp (BATTERY): This lamp flickers to recommend the battery replacement. For the replacement, consult Sanyo sales representative or agent. 3. Alarm lamp (ALARM): This lamp is flashed ...

  • Sanyo MDF-U7486S - page 12

    - 53 - 11 INSTALLATION SITE T o operate this unit properly and to obtain maximum performance, install the unit in a locati on with the following conditions:  A location not subjected to direct sunlight Do not install the unit under direct sunlight. Installation in a location subjected to direct sunlight cannot obtain the intended performance. ? ...

  • Sanyo MDF-U7486S - page 13

    - 54 - 12 INSTALLATION 1. Remove the packaging materials and tapes Remove all transportation packaging materials and tapes. Open the doors and ventilate the unit. If the outside panels are di rty, clean them with a diluted neutral dishwa shing detergent. (Undiluted detergent can damage the plastic components. For the dilution, refer to the instruct ...

  • Sanyo MDF-U7486S - page 14

    - 55 - 13 START-UP OF UNIT Follow the procedures for the initial and consequent operations of the unit. 1. Turn off the switch of the back-up system (optional component) if it is installed. 2. Connect the power supply cord to the dedicated outlet having appropriate rating with the chamber empty, and turn on the power switch on the freezer. 3. Turn ...

  • Sanyo MDF-U7486S - page 15

    - 56 - 14 CHAMBER TEMPERATURE SETTING Table 1 shows the basic procedu re for setting the chamber temperature. Perform key opera tions in the sequence indi cated in the table. The example in the table is based on the assumption that the desired temperature is -75 o C. Note: The unit is set at the factory that the chamber temperature -80 o C. Table 1 ...

  • Sanyo MDF-U7486S - page 16

    - 57 - 15 ALARM TEMPERATURE SETTING This unit is provided with the hig h and low temperature alarm a nd the temperature at which the alarm is activated is changeable. The following proced ure shows the setting of alarm temperature according to the condition below: High temperature alarm: activates at the temperature 5 o C higher than the set temper ...

  • Sanyo MDF-U7486S - page 17

    - 58 - 16 SETTING OF ALARM RESUME TIME The alarm buzzer is silenced by pressi ng alarm buzzer stop key (BUZZER) on the control panel du ring alarm condition. (A remote alarm is continuing the operation.) The buzzer will be activated again after certain su spension if the alarm condition is continued. Th e suspension time ca n be set by following th ...

  • Sanyo MDF-U7486S - page 18

    - 59 - 17 REMOTE ALARM TERMINAL The terminal of the remote alarm is installed at the lower left side of the unit. The alarm is outputted from this terminal. Contact capacity is DC 30V, 2 A. Contact output: between COM. and N.O. between COM. and N.C. At normal Open Close At abnormal Close Open Note: • The alarm buzzer is silenced by pressi ng alar ...

  • Sanyo MDF-U7486S - page 19

    - 60 - 18 SETTING OF COMPRESSOR DELAY TIME The delay time of high and low stage side compre ssor can be changed to reduce the loa d on the power line and to facilitate the start-up (reset ) of the freezer after power fa ilure. The example in the table is based on the assumption that the delay time is changed to 4 minutes. (The delay time is set in ...

  • Sanyo MDF-U7486S - page 20

    - 61 - 19 ALARMS & SAFETY FUNCTIONS This unit has the alarms and safety functions shown in Table 7, and also self diagnostic functions. Table 7. Alarms and safety functions Alarm Situation Indication Buzzer Safety functions High temperature alarm If the chamber temperature is higher than the temperature at which the high temperature alarm is ac ...

  • Sanyo MDF-U7486S - page 21

    - 62 - 20 ROUTINE MAINTENANCE WARNING Always disconnect the power supply to the unit prior to any repair or maintenance of the unit in order to prevent electric shock or injury. Ensure you do not inhale or co nsume medication or aerosols from around the unit at the time of maintenance. These may be harmful to your health. Cleaning of cabinet 㻊 Cl ...

  • Sanyo MDF-U7486S - page 22

    - 63 - 21 ROUTINE MAINTENANCE Defrosting of inside wall The frost is built at the upper portion of the chamb er and inner door. The excessive frost possibly make some gap between the cabinet and magnetic door ga sket, which may cause poor cooling. Remove the frost on the inner door with a scraper enclosed wi th the unit. Following shows the procedu ...

  • Sanyo MDF-U7486S - page 23

    - 64 - 22 ROUTINE MAINTENANCE Cleaning of air intake port The cap of the left side i s turned counterclockwise (Counterclockwi se direction), a nd this product is removed, and the outer air is adopted into the chamber, and it opens a outer d oor. Therefore, frost is easy to be settled around the air intake port inside the chamber. Clean it in the c ...

  • Sanyo MDF-U7486S - page 24

    - 65 - 23 TROUBLE SHOOTING If the unit malfunctions, check out the following before calling for service. Malfunction Check/Remedy The chamber is not cooled at all 㻊 The circuit breaker of power source is active. 㻊 The voltage is too low (In this case, call an electri cian). 㻊 The power is not supplied. 㻊 The breaker is free. 㻊 The large a ...

  • Sanyo MDF-U7486S - page 25

    - 66 - 24 DISPOSAL OF UNIT WARNING If the unit is to be stored unused in an unsupe rvised area for an extended perio d ensure that children do not have access and doors canno t be closed completely . The disposal of the unit should be accomplished by appropriate personnel. Alw ays r emo ve doors to prevent accidents such as suffocation. Recycle of ...

  • Sanyo MDF-U7486S - page 26

    - 67 - 25 DISPOSAL OF BATTERY Location of a nickel-metal-hydride battery This unit is provided a nickel-metal-hyd ride battery for the power failure warning device. The battery is located in the electrical box inside the cover on the lower left side. (Fig. 1) The high voltage compone nts are enclosed in the el ectrical box. The cover should be remo ...

  • Sanyo MDF-U7486S - page 27

    - 68 - 26 BACK-UP SYSTEM (OPTION) WARNING As with any equipment that uses CO 2 gas, there is a likelihood of oxygen depletion in the vi cinity of the equipment. It is important that y ou assess the work site to endure there is suitable and sufficient ventilation. If restricted ventilation is suspected, then other methods of ensuring a safe environm ...

  • Sanyo MDF-U7486S - page 28

    - 69 - 27 TEMPERATURE RECORDER (OPTION) Installation of MTR-85H/MTR-G85 Contact Sanyo sales representative or a gent for the attachment of an automatic temperature recorder. : INTERFACE BOARD (OPTION) Installation of MTR-480/MTR-L03 Contact Sanyo sales representative or agent for the attachment of a interface board. : Note: 㸨 When a data transmit ...

  • Sanyo MDF-U7486S - page 29

    - 70 - 28 INVENTORY RACK (OPTION) The optional inventory rack is useful to store th e precious materials in the ch amber effectively. When the rack is used, it is necessary to adjust the height of the shelves. Set the shelf support as shown in the figure below. Shelf support Shelf stopper NO. 8 under the seco nd screw from the top No. 3 under the f ...

  • Sanyo MDF-U7486S - page 30

    - 71 - 29 SPECIFICATIONS Name Ultra-Low Temperature Freezer Model MDF-U5486S MDF-U5486SC External dimensions W890 x D870 x H1990 (mm) Internal dimensions W630 x D600 x H1280 (mm) Effective capacity 483 L Exterior Painted steel Interior Painted steel Outer door Painted steel Inner door ABS resin panel with stainless frame, 2 doors Shelf Stainless st ...

  • Sanyo MDF-U7486S - page 31

    - 72 - 30 SPECIFICATIONS Name Ultra-Low Temperature Freezer Model MDF-U7486S MDF-U7486SC External dimensions W1130 x D875 x H1990 (mm) Internal dimensions W870 x D600 x H1280 (mm) Effective capacity 668 L Exterior Painted steel Interior Painted steel Outer door Painted steel Inner door ABS resin panel with stainless frame, 2 doors Shelf Stainless s ...

  • Sanyo MDF-U7486S - page 32

    - 73 - 31 PERFORMANCE Model MDF-U5486S MDF-U5486SC (for U.S.A. only) MDF-U7486S MDF-U7486SC (for U.S.A. only) Cooling performan ce -86 o C at the center of the chamber (ambient temperature; 30 o C, no load) Temperature control range -50 o C to -86 o C (ambient temperature; 30 o C, no load) Power source 220 V, 60 Hz Rated power consumption 1180 W 12 ...

  • Sanyo MDF-U7486S - page 33

    - 7 4 - 32 CAUTION Please fill in this form before servicing. Hand over this form to the service engineer to keep for his and your safety. Safety check sheet 1. Freezer contents : Risk of infection: Risk of toxicity: Risk from radioactive sources: (List all potentially hazardous materials that have been stored in this un it.) Notes : 2. Contaminati ...

  • Sanyo MDF-U7486S - page 34

    SANY O Electric Co., Ltd Printed in J apan ...

Produzent Sanyo Kategorie Freezer

Dokumente, die wir vom Produzenten des Geräts Sanyo MDF-U7486S erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Sanyo
- Bedienungsanleitungen MDF-U7486S
- Produktkarten Sanyo
- Informationsbroschüren
- oder Energieetiketten Sanyo MDF-U7486S
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Sanyo MDF-U7486S.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Sanyo MDF-U7486S, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Sanyo MDF-U7486S. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Sanyo MDF-U7486S ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Sanyo MDF-U7486S, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Sanyo MDF-U7486S hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Sanyo MDF-U7486S verständlich ist.

Eine gänzliche Bedienungsanleitung von Sanyo sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Sanyo MDF-U7486S bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Sanyo MDF-U7486S befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Sanyo MDF-U7486S, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Sanyo MDF-U7486S - die uns die ersten Schritte während der Nutzung von Sanyo MDF-U7486S erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Sanyo MDF-U7486S hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Sanyo MDF-U7486S im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Sanyo MDF-U7486S?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Sanyo MDF-U7486S nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Sanyo MDF-U7486S hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)