Deutsch dropdown-ico

Bedienungsanleitung BlueWalker PowerWalker VFI 40000TP 3/3 BE

64 Seiten Betrifft nicht
Download

Zur Seite of 64

Summary
  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 1

    PowerW alker VFI 3/3 Series VFI 30000TP/40000TP 3/3 BE/BI 380/400/415V 50/60Hz (3-phase input/output) User Guide ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 2

    ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 3

    EN ©2013 BlueW alker GmbH All Rights Reserved The contents of this manual are the copyright of the publisher and may not be reproduced (even extracts) unless permission granted. Every care has been taken to ensure the accuracy of the information contained in this manual, but no liability can be accepted for any errors or omission. The right to mak ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 4

    4.1 De li v e ry ch e ck …………………………………………………… ………………… 4 .2 U n p ac k in g an d visual i ns p ec ti on … … ……… … …… … …… … ……… … …… 4. 3 P lann i n g be fo re install ati on ………………… …… ……… …… ……… ………… 4 .4 C a b inet i ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 5

    EN R ec ycli n g th e us ed U PS o r ba tte ry …… ………… …… …… …… ………… …… Maint en an ce ………………… ………… ………… …………………… ………… …… P arall el syste ms … …… …… . … … …… …… …… ……… …… …… …… …… … …… 8. 9. 10. Elec t ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 6

    1 1 Safety instructions W arning! Operations inside the UPS must be performed by a service engineer from the manufac- turer or from an agent authorised by the manufacturer . 1.1 Safety caution Use the optional Maintenance Bypass Switch (MBS) for service inside the UPS when in - stalled to the system. Remember to open battery cabinet(s) breaker . Al ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 7

    2 EN 1.3 CE marking The product has the CE marking in compliance with the following European directives: L VD Directive (Safety) 2006/95/EEC EMC Directive 2004/108/EEC The only user operations permitted are: Start up and shut down the UPS, excluding the commissioning start-up.Use of the LCD con - trol panel and Emergency Power Off (EPO) switch.Use ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 8

    3 1.5 Environment The UPS must be installed according to the recommendations in this manual.Under no cir - cumstances the UPS should be installed in an airtight room, in the presence of ammable gases, or in an environment exceeding the specication.Excessive amount of dust in the operating environment of UPS may cause damage or lead to malfunc ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 9

    4 EN 2 Introduction 2.1 System description PowerW alker VFI 3/3 Series products are high-efficiency and high-performance, double conversion, pure-online and three phase input and three phase output UPS, with unit capacity ranging between 20KV A-40KV A. Categorized by capacity , the products can be further divided into 20KV A, 30KV A and 40KV A. Thi ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 10

    5 2.2 Basic system conguration 2.3 Panel gure ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 11

    6 EN 2.4 Exterior view ① AC: This light and inverter light will turn "green" when UPS is powered by Rectier Input; ② Inverter: This light will turn "green" when UPS load is through the inverter; ③ Battery: This light will turn "yellow" when UPS is powered by batteries; ④ Bypass: This light will turn "gr ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 12

    7 CHGR F AN Front view(door open) Battery trays ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 13

    8 EN W × D × H (mm) 3 T echnical data 3.1 Standards Product IEC62040-3:1999 and EN62040-3:2001 UPS VFI 30000TP 3/3 BE/BI VFI 40000TP 3/3 BE/BI Safety IEC62040-1:2008,EN62040-1:2003 and EN60950-1:2005 EMC IEC62040-2:2006 and EN62040-2:2005 3.2 Environment 0 ℃ ～ +40 ℃ (with batteries) Working T emperature 0 ℃ ～ +40 ℃ Storage T emperatur ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 14

    9 3.5 AC input 3.4 Characteristics VFI 30000TP 3/3 BE/BI VFI 40000TP 3/3 BE/BI Noise (ISO 7779) <57dB at 75% load Efciency-nominal load Up to 92% V oltage (L-N) 121V -274 V olts without using battery Rectier input 3 phases + N Bypass input 3 phases + N Frequency 40-70 Hz Rated input voltage 380V/400 V/415V Power factor 0.99 Input distortio ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 15

    10 EN 3.7 AC output 3.8 Battery and Charger Internal battery package Panasonic LC-RW 1245W / CSB HR 1234WF2 Dimensions 94*151*64.5/pc(Panasonic) 94*151*65/pc(CSB) Strings 2 x 16 Charger Input Protection 8 A fuse Rated Charge V oltage ± 216V Default for Integrated bettery Initial Charging Current 4.5A Battery Leakage < 3.5mA Battery protection 1 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 16

    11 4 Mechanical installation 4.1 Delivery check The UPS and accessories are delivered on a specically designed pallet that is easy to move with a forklift or a pallet jack. Keep the UPS always in upright position and do not drop the equipment. Do not stack the pallets. The UPS is delivered with the following items: 1. Winpower disc 2.RS-232 seri ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 17

    12 EN Check the information on the type designation label of the equipment to verify that the unit is of the correct type. The type designation label includes ratings, a CE marking, a type code, a part number and a serial number . The serial number is important when making inquiries. It allows individual recognition of the equipment. ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 18

    13 Preparation for installation. 1. A void extremes of ambient temperature; excessive dust, moisture or vibration; ammable gases; and corrosive or explosive atmospheres. 2.Altitude for normal UPS function should not exceed 1000m. 3.The battery cabinet should work within a temperature range from15 ℃ to 25 ℃ . 4.The maximum ambient temperature ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 19

    14 EN Caution! UPS cabinet(s) can fall over if the installation brake pads are not used. Both rear and front pads must be used to secure the UPS cabinet to the oor . Use a 19mm wrench in clockwise direction to screw the brake pad down to the ground, keeping the machine from moving. 4.5 Maintenance Bypass Switch(MBS) The operation of the MBS is a ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 20

    15 The normal positions of the MBS switches. The switching sequence for circuit breaker from normal position to maintenance position: ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 21

    16 EN The maintenance positions of the MBS switches 2.Use LCD to turn the UPS from normal mode to bypass mode: Switch-off action (press ESC to exit above picture) T ransfer UPS from normal mode to maintenance bypass mode: 1.The normal start position should be following: ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 22

    17 1)Switch-off picture 2)If it is in single machine mode, the following will appear Remember to verify the transfer before proceeding the next step. 3.Remove the locking plate of maintenance switch. 4.T urn OFF the Rectier Input switch and battery breaker. 5.T urn the Maintenance switch to “ MAINTENANCE ” side. 6.T urn OFF the Bypass Input ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 23

    18 EN 7.UPS is now in the maintenance bypass mode, see below (Note: the Serv disconnect i.e. battery breaker must be turned off): T ransfer UPS from maintenance bypass mode to normal mode: 1.The normal start position should be following: When the LED of bypass turns green,the UPS enters into bypass mode. 3.T urn the Maintenance switch to “ UPS ? ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 24

    19 Then the UPS turn to bypass mode. 4.T urn ON the Rectier Input switch and battery breaker. 5.Use LCD to turn the UPS from bypass mode to normal mode: Switch-off action (press ESC to exit above picture) 1)Switch-on picture 2)Press ENTER ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 25

    20 EN 6.UPS is now in the normal mode,see below: 7.Remount the locking plate of maintenance switch to the position to prevent the use of it. ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 26

    21 5 Electrical installation 5.1 Electrical Preparations The UPS unit has the following power connections: Three-phase (L1, L2, L3), Neutral (N) and Protective Earth (PE) connection for the rectier input. Three-phase (L1, L2, L3), Neutral (N) and Protective Earth (PE) connection for the bypass input ( N is INTERNALL Y common for rectier and b ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 27

    22 EN 1.If UPS rectier input and bypass input are supplied from two mains: Connect the mains 1 supply cables to the UPS rectier input terminals L1, L2, L3, N and PE. Connect the mains 2 supply cables to the UPS bypass input terminals L1, L2, L3, N and PE. 8 blue wires (B14, B15, B16, and B18) for BA TN connection; 56 black wires (B1) with an ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 28

    23 T erminal block diagram W arning! High touch current earth connection essential before connecting supply . 2.If UPS rectier input and bypass input are supplied from one mains only: Connect the mains supply cables to the UPS rectier input terminals L1, L2, L3, N and PE . The following three jumpers must be xed between the rectier and ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 29

    24 EN The conductor cross sections apply for maximum currents: (1) For PVC-insulated copper cables (at 70 ℃ ) (2) When routed in conduits for electrical installations (3) When air temperature surrounding the conduits does not exceed 30 ℃ (4) For cable lengths up to 30 m Connect the Protective Earthing (PE) cable rst. Connect other cables as ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 30

    25 Routing of communication cables or data lines should be kept separate from the UPS input, output, and external battery cables. Use cable cross section and protective device specication Model VFI 30000TP 3/3 BE/BI VFI 40000TP 3/3 BE/BI Rectier Input L1, L2, L3, N, Bypass Input L1, L2, L3, N, min. conductor cross section[mm ] 10 16 max. poss ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 31

    26 EN Notice! The following label must be displayed on all switching devices installed in the same electrical system as the UPS, even when these are located at a distance from the area in which it is located (according to European standard EN 62040-1). W arning! ENSURE THA T THE UNINTERRUPTIBLE POWER SYSTEM IS ISOLA TED BE - FORE WORKING ON THIS CI ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 32

    27 Step1: Put batteries into the trays (see Fig. 2). Fig. 2 3. Assemble the battery packs.There are eight batteries in each battery pack, four packs in each shelf and total is four shelves. Step2: connect the wires between the batteries (see Fig. 3). Fig. 3 Front Back ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 33

    28 EN Step3: Install the top tray downward, and fold both the top and bottom tray anges (see Fig 5). Fig. 5 Please refer to the following gure(Fig.4) for wire connections of the four battery packs. Fig. 4 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 34

    29 Step4: T ape two sides (see Fig.6 ).Make sure the cable is placed between the tray edges during tape mounting. Fig. 6 Front Back Battery Pack Assembly Step5: Paste the labels to the battery packs (see Fig. 7). Fig. 7 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 35

    30 EN 4. Put the battery packs into the enclosure from left to right and bottom to top and cover each shelf with a x-plate(see Fig. 9) (please refer to Fig.4 for correspending battery packs). Fig. 9 Make sure to paste the correct label to each battery pack and the battery packs are placed conformably with the labels, i.e. the battery terminals a ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 36

    31 5. Connect the cables to each shelf respectively (see Fig. 10). REMARK: MAKE SURE TO CONNECT WIRES WITH THE SAME COLOR. Fig. 10 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 37

    32 EN Fig.1 1 6. Secure each x-plate with four screws (see Fig. 1 1). 7. T ie up the wires properly(see Fig. 12). Fig.12 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 38

    33 8. Reinstall the battery cover and secure it with the eighteen screws. 8 8 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 39

    34 EN Notice! The most common battery type used in UPS installations is the valve regulated bat - tery . V alve regulated cells are not sealed. The amount of gas given off is less than for ooded cells, but when planning the battery installation, allowance must be made for adequate ventilation and heat dissipation. V alve regulat ed cells are not ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 40

    35 5.6 Connections between battery cabinet and UPS Make sure the Protective Earthing (PE) connected rst. External Battery Cabinet Connections Notice! The requirements of the EC directives are satised when battery cabinet are used with original accessories. If alternative batteries are used, you must ensure that the appli - cable EC directives ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 41

    36 EN Exchanging batteries W arning! If a battery cabinet has been disconnected and is to be reconnected, the battery isola - tor may only be reconnected after you have made certain that voltage with the correct polarity is present on both sides of isolating device. Connecting external battery cabinet W arning! Before replacing batteries, make sure ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 42

    37 6 Software and connectivity The Series provide Intelligent Slot, Expanded Slot, P ARALLEL, AS400, EPO, RS485 and RS232 as well as SERVICE Supervising Communication Interface exclusively available to PowerW alker technical personnel. 2 6 8 1 5 P ARALLEL Intelligent slot Expanded slot AS400 EPO SERVICE RS485 RS232 3 4 7 P ARALLEL 1. Intelligent sl ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 43

    38 EN RS232 port RS485 port ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 44

    39 AS400 port Note! The UPS have to be manually reset if remote shutdown occurs. ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 45

    40 EN 7 User operations 7.1 Single machine operation W arning! High touch current earth connection essential before connecting supply . The only user operations permitted are: Start up and shut down the UPS, excluding the commissioning start-up. Use of the LCD control panel and Emergency Power Off (EPO) switch. Use of optional connectivity modules ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 46

    41 3)Press ESC to access or automatically within 1min with no button being pressed 4)Press ▼ to obtain the below informa - tion Remark: the following drawing takes PowerW alker VFI 30000TP 3/3 BE/BI as an example and statistics are only for reference. 1)Power on 2)Automatic access within about 4s 36 POWERWALKER VFI 3 0000TP 3/3 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 47

    42 EN 5)Press ▼ again to obtain the below 6)Press ▼ again to obtain the below information information 7)Press ▼ again to obtain the below 8)Press ▼ again to obtain the below information information VFI 3 0000TP 3/3 ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 48

    43 1)Switch-on picture 2)Press ENTER 4. Start-up action (press ESC to exit the above picture) Note! If malfunction occurs, “x” will appear at the lower right corner of the display ,while a warning occurs, “ ” will appear at the same position (as illustrated in the below pic - ture with battery mode as an example). ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 49

    44 EN 3)Select “Y es, Conrm” to switch on 4)Normal Switch-on the machine 5)Battery power supply (switch off line input switch) ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 50

    45 3)If it is in parallel machine mode, the 4)Press ENTER following will appear 5. Switch-off action (press ESC to exit above picture) 1)Switch-off picture 2)If it is in single machine mode, the following will appear ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 51

    46 EN 5)Select “Y es, Conrm” to switch of f 6)Normal Switch-off the machine Note! If you intend to switch off only one set of UPS among the parallel machine system, se - lect “single machine switch-off”; if switch-off is intended for the entire parallel machine system, select “parallel machine switch-off”. 6. Help 1)Help picture 2)Pr ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 52

    47 3)Enter respective password 4)Select action item 8. The Series is capable of DC start-up without AC input, panel display being similar to switch-on picture with AC supply . DC switch-on and off are available by following instruc - tions appearing in the pictures. 1)Action display (bypass power supply) 2) Press ▼ 7. Conguration (press ESC to ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 53

    48 EN 9. Procedures of DC switch-on: Activate DC switch-on function set under UPS bypass mode Make sure that “+”, “-” and “N” wires of batteries are properly connected to UPS Switch on batteries Lightly touch ENTER Manually conduct switch-on order within about 1min after LCD self-inspection 7.2 Parallel machine operation Redundancy intr ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 54

    49 Parallel machine wire connection drawing(one battery supply) Parallel machine wire connection drawing(separate battery supply) ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 55

    50 EN Single machine wire connection drawing ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 56

    51 PowerW alker VFI 30000TP , 40000TP 3/3 BE/BI requires minimum maintenance. 1. If battery is switched off, loaded equipments will not be covered for power-of f protection. 2. Make sure UPS vent are properly ventilated and clean side frames and fan vents from dusts every half a year (switch off AC, battery cabinet and internal battery fuse prior t ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 57

    52 EN Remark: A. Prior to battery replacement, switch off UPS and remove it from AC and battery , take of f internal battery breaker . B. T ake off metallic articles such as rings and watches. C. Use screw drivers equipped with insulated handles and do not place tools or other metal - lic substances on the batteries. D. Short circuit or reverse con ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 58

    53 8.2 Regular service/intervals The UPS requires very little maintenance if installed in an appropriate environment. In order to ensure maximum availability of the UPS, manufacturer recommends signing a proactive service agreement with a local authorised service provider . Batteries test 18 months Maintenance Interval Batteries change 3-5 years or ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 59

    54 EN 9 Parallel systems Parallel is only connected to identical ports for the UPS of same models and kV A rating. 1) Follow installation instructions for general installation requirements. 2)V entilation spacing between machines should allow for service access. 3) Input wiring for each set of UPS should follow the requirements for that of single u ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 60

    55 Note! Parallel signal cable should be connected as a loop. ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 61

    56 EN 1 1 Display reference T able ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 62

    57 Should any display or warning message excluded in the above table be found,please con - tact distributor or call PowerW alker Hot line for advice. ● Indicator light is on ★ Indicator light ashes Warning include one or more than one of these: 1.EPO active 2.Line loss 3.Neutral loss 4.Line phase error 5.Bypass loss 6.Bypass phase error 7.Ba ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 63

    ...

  • BlueWalker PowerWalker VFI 40000TP 3/3 BE - page 64

    614-01719-00 ...

Produzent BlueWalker Kategorie Uninterruptible power supply (

Dokumente, die wir vom Produzenten des Geräts BlueWalker PowerWalker VFI 40000TP 3/3 BE erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen BlueWalker
- Bedienungsanleitungen PowerWalker VFI 40000TP 3/3 BE
- Produktkarten BlueWalker
- Informationsbroschüren
- oder Energieetiketten BlueWalker PowerWalker VFI 40000TP 3/3 BE
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung BlueWalker PowerWalker VFI 40000TP 3/3 BE.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen BlueWalker PowerWalker VFI 40000TP 3/3 BE, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen BlueWalker PowerWalker VFI 40000TP 3/3 BE. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts BlueWalker PowerWalker VFI 40000TP 3/3 BE ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts BlueWalker PowerWalker VFI 40000TP 3/3 BE, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von BlueWalker PowerWalker VFI 40000TP 3/3 BE hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von BlueWalker PowerWalker VFI 40000TP 3/3 BE verständlich ist.

Eine gänzliche Bedienungsanleitung von BlueWalker sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von BlueWalker PowerWalker VFI 40000TP 3/3 BE bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von BlueWalker PowerWalker VFI 40000TP 3/3 BE befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich BlueWalker PowerWalker VFI 40000TP 3/3 BE, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts BlueWalker PowerWalker VFI 40000TP 3/3 BE - die uns die ersten Schritte während der Nutzung von BlueWalker PowerWalker VFI 40000TP 3/3 BE erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit BlueWalker PowerWalker VFI 40000TP 3/3 BE hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von BlueWalker PowerWalker VFI 40000TP 3/3 BE im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich BlueWalker PowerWalker VFI 40000TP 3/3 BE?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit BlueWalker PowerWalker VFI 40000TP 3/3 BE nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit BlueWalker PowerWalker VFI 40000TP 3/3 BE hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)