-
Sanyo VCC-6594 - page 1
INSTRUCTION MANUAL VCC-6594 COLOR CCD CAMERA About this manual B efo re in st a ll in g a nd us in g th e ca m e ra, pl ea se re ad th is ma nu al carefully. Be sure to keep it handy for later reference. L53 H4 /US (VCC -6 594) GB 2001 , 1 1, 9 ...
-
Sanyo VCC-6594 - page 2
SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty . The names and addresses of Authorized Sanyo Service Centers may be obtaine ...
-
Sanyo VCC-6594 - page 3
1AC6P1P2413-- L53H4/US(1101KPS-CZ) 21605 Plummer Street, Chatsworth, California 91311 Printed in Japan L53 H4 /US (VCC -6 594) GB 2001 , 1 1, 9 ...
-
Sanyo VCC-6594 - page 4
Depen ding on the co ndit ions of use, instal lation and envir onme nt , please be s ure t o ma ke t he a ppr opri ate sett ing s and adjustm en ts. I f you need hel p wit h insta ll ation a nd/ or se tti ngs, plea se con sult your deale r. CONTENTS INFORMATION TO USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PRECAUTI ...
-
Sanyo VCC-6594 - page 5
INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform ...
-
Sanyo VCC-6594 - page 6
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For ...
-
Sanyo VCC-6594 - page 7
PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment volume (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume. 3 Pow ...
-
Sanyo VCC-6594 - page 8
PARTS NAMES 5 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 6 Flange-back adjustment screw (FLANGE BACK ADJ.) 7 Flange-back lock screw (FLANGE BACK LOCK) 8 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixin ...
-
Sanyo VCC-6594 - page 9
PARTS NAMES 9 Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F Camera setup section (under the cover) These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment ...
-
Sanyo VCC-6594 - page 10
CONCERNING AUTO-IRIS LENSES DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO type auto-iris lens A lens with amplifier circuit that operates on video si ...
-
Sanyo VCC-6594 - page 11
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Check the lens mount Do not use a lens if the length “ L ” is more than 5 mm. That may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount with the c ...
-
Sanyo VCC-6594 - page 12
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut the cabl e at the plug, t hen remov e appr ox. 8 m m of th e ca ble sh eath an d s trip ab out 2 m m from each wire. 2 Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then cl ...
-
Sanyo VCC-6594 - page 13
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.), AC adaptor and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Use a commercially available 24 V AC adaptor. Connect an AC 24 V power source to the AC 24 V input terminal ...
-
Sanyo VCC-6594 - page 14
SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. * The sticker on the inside of cover. Control name Position ...
-
Sanyo VCC-6594 - page 15
SETTINGS Electronic shutter settings and electronic iris settings When all of these switches are down, electronic shutter (1/60 sec or auto iris setting) is enabled. The electronic shutter can be set to one of 7 speeds as shown in Table A . Furthermore, when all switches are up, electronic iris setting is enabled. Notes on the electronic shutter: ? ...
-
Sanyo VCC-6594 - page 16
SETTINGS Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 6 ( MULT ) and 7 ( CENT ) are set to the down ( OFF ) position. Change the backlight compensation switch settings depending on the conditions. • MULT mode: Use this position when applying backlight compens ...
-
Sanyo VCC-6594 - page 17
SETTINGS White balance adjustment Normally the switch 8 ( WB ) is set to the down ( ATW : auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the switch 8 ( WB ) to the up ( M : manual) position, then adjust the colour. • Turn RED (VR302) to s ...
-
Sanyo VCC-6594 - page 18
SETTINGS Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. 1 Set the switch 9 ( SYNC ) to the up ( LL ) position. 2 Switch the display on the monitor from camera 1 to camera 2. Adjust the LINE PHASE volume ...
-
Sanyo VCC-6594 - page 19
TROUBLESHOOTING Bef ore taking the c ame ra for re pair s, plea se chec k be low to ma ke sure tha t th e ca mera is used c orrectly . I f it st ill does n ot p e rform corre ctly , pl ease consul t yo ur d ealer or a S anyo Aut horiz ed S ervi ce Ce ntre. No picture on the monitor screen • Is the po wer turn ed o n to all connec ted devices ? I ...
-
Sanyo VCC-6594 - page 20
SPECIFICATIONS Camera: Scanning system : NTSC standard TV system (525 TV lines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 811 (H) x 508 (V) Effective picture elements : 768 (H) x 494 (V) Synchronizing system : Internal sync, Line lock manually switchable Resolution : 520 TV ...
Haben Sie eine Frage bezüglich Sanyo VCC-6594?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Sanyo VCC-6594 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Sanyo VCC-6594 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.