Deutsch dropdown-ico

Bedienungsanleitung Bunn CDS-3

60 Seiten 6.43 mb
Download

Zur Seite of 60

Summary
  • Bunn CDS-3 - page 1

    OPERA TING & SER VICE MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 www .bunnomatic.com CDS-2 CDS-3 27646.0000N 04/08 ©1997 Bunn-O-Matic Corporation T o obtain the Illustrated Parts Catalog, visit the Bunn-O-Matic website, at www .bunn.com. This is absolutely ...

  • Bunn CDS-3 - page 2

    2 INTRODUCTION This equipment dispenses granita-type and cold liquid drinks on demand from separate hoppers. Operating controls are accessible only to key operators. CONTENTS Introduction & Warranty .....................................................................................2 User Notices ............................................... ...

  • Bunn CDS-3 - page 3

    3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 12559.0003 HAZARDOUS VOL T AGE DISCONNECT FROM POWER SOURCE BEFORE REMOVING! WA RNING CHARGE T ype R22, Amount 8.4 oz Design Pressu ...

  • Bunn CDS-3 - page 4

    4 USER NOTICES (CONT .) CHARGE T ype R22, Amount 8.4 oz Design Pressures: High 210 Low 32 AFTER CLEANING & BEFORE REASSEMBL Y LUBRICA TION 1 2 3 27664.0000D 5/97 © 1996 BUNN-O-MA TIC CORPORATION 1. Apply lubricant* on lip of auger seal where contact is made with cooling drum. 2. Apply lubricant* on outside surface of cooling drum seal or insid ...

  • Bunn CDS-3 - page 5

    5 SITE PREP ARA TION These dispensers are very heavy . Place them on a sturdy counter or shelf capable of supporting at least 180 lbs for the CDS2 and 250 lbs for the CDS3. They are for indoor use only . The dispenser must have at least four inches of space behind it. This space is needed for airflow, air filter removal, and cleaning. Minimal cle ...

  • Bunn CDS-3 - page 6

    6 6.0" MIN. 6.0" MIN. 6.0" MIN. DO NOT REMOVE INITIAL SETUP CAUTION – The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . 1. Set the dispenser on the counter where it will be used. The CDS-3 dispenser requires a minimum of 6.0” air clearance on both sides and at ...

  • Bunn CDS-3 - page 7

    7 9. Align the auger shaft with the flat fin of the auger . Push the augers as far as they will go and rotate them so the flat fins are pointing up. 10. Thoroughly rinse the hoppers and install them over the cool- ing drums with augers. Slide them into place and push them down as far as they will go. As much as possible, keep lubricant from the ...

  • Bunn CDS-3 - page 8

    8 ICE CONTROLS Controls the consistency of the ice in the hoppers when the DA Y/NIGHT switch is in the left “DA Y” position and the ICE/OFF/NO-ICE switch is in the left “ICE” position. T urn this control clockwise to produce a coarse r ice or c ounter clockwis e to produce a finer ice. (The dispenser is set to deliver satisfactory ice at a ...

  • Bunn CDS-3 - page 9

    9 DA Y/NIGHT TIMER The quartz driven timer offers 24-hour programming with 96 actuators that operate in 15-minute incre- ments. All actuators can be individually set to the inside or outside position. The timer is located behind the right side panel. Shown in “Night Time” Mode Shown in “Day Time” Mode OPERA TING CONTROLS (Cont.) TWO FLASHES ...

  • Bunn CDS-3 - page 10

    10 USING THE DISPENSER FOR GRANIT A-TYPE PRODUCTS 1. Slide the lid for the selected hopper to the front or back to gain access to the hopper . 2. Place the premixed liquid product in the selected hopper . 3. Simply press all switches to the center of the control drawer for granita products. a. Place the POWER OFF/ON switch in the right “ON” pos ...

  • Bunn CDS-3 - page 11

    11 OTHER RECOMMENDA TIONS FOR YOUR DISPENSER • Whetherliquidconcentrateorgranulatedpowder ,allproductmustbethoroughlymixedBEFOREaddingit to the hoppers. • Forbestresultswithgranita-typeproducts,useonlyproductswithan apparentbrixof12orhigher .So ...

  • Bunn CDS-3 - page 12

    12 RECOMMENDED DAIL Y CLEANING (SUGAR & ALCOHOL PRODUCTS!) NOTE – Close the control drawer before proceeding. 1. Empty all product from the hoppers. 2. The driptray should be cleaned as needed for proper presentation of the product. 3. MixapacketofKay-5Sanitizerdilutedwithtwo-gallonsofwarm(120°F)wate ...

  • Bunn CDS-3 - page 13

    13 1. Squeeze some lubricant into hand. 2. Apply a thin film of lubricant to each cooling drum seal. 3. Install the seals over the flange at the re ar of the cooling drums as shown. 4. Press the seals firmly into place. 5. Apply a thin film of lubricant to the inside of each auger shaft seal. 6. Install the seals on the auger shafts. Wipe the co ...

  • Bunn CDS-3 - page 14

    14 F AUCET HANDLES Dispensing from the hoppers will occur when the faucet handles are installed with the handles in the upright position. (shown, left hopper) Dispensing from the hoppers will not occur when the handles are in- stalled upside-down. (shown, right hopper) Y ou may consider this handle position when the product in the hoppers is not ye ...

  • Bunn CDS-3 - page 15

    15 AUGER ASSEMBL Y & DISASSEMBL Y (EARL Y AUGERS ONL Y) Auger Sections (3 req’d.) Auger Nose Short Auger Latch Long Auger Latch ASSEMBL Y 1. Snap one of the auger sections to the long auger latch. 2. Snap another auger section in place. 3. Snap the thir d auger section in place. 4. Sn ap the au ge r nos e on to th e last section installed. 5. ...

  • Bunn CDS-3 - page 16

    16 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department. • Inspection, testing, and repairof electricalequipment should? ...

  • Bunn CDS-3 - page 17

    17 TROUBLESHOOTING (cont.) REMEDY (A) The cir cuit breaker must not be tripped. (B) Refer to Ser vice - Circuit Breaker for testing procedures. See page 27. Remove the lamps and check for continuity across the base and tip. Replace if necessary . Refer to Ser vice - T ransformer for testing procedures. See page 49. Refer to Service - Lamp Holder/So ...

  • Bunn CDS-3 - page 18

    18 TROUBLESHOOTING (cont.) PROBLEM Compressor not running (With Adjustment Board L.E.D.s ON steadily for two minutes) Compressor runs but will not cool (With adjustment Board L.E.D.s flashing once every 4 seconds) Compressor runs but will not cool (With adjustment Board L.E.D.s flashing twice every 4 seconds) Compressor runs but will not cool (Wi ...

  • Bunn CDS-3 - page 19

    19 TROUBLESHOOTING (cont.) PROBLEM Compressor runs but will not cool (With adjustment Board L.E.D.s flashing 3, or 4 times ever y 4 seconds) (cont.) Product Won’t Freeze Product freezes but ice granules are too fine or too large Dispenser is making unusual noises. (S ome no ises are a nor ma l oc cu ranc e with this type of device. Y ou need to ...

  • Bunn CDS-3 - page 20

    20 TROUBLESHOOTING (cont.) PROBLEM Dispenser is making unusual noises. (S ome no ises are a nor ma l oc cu ranc e with this type of device. Y ou need to become familiar with those that are normal , to determi ne when they have become unusual.) (cont.) Product is leaking into the inside of the drum. PROBABLE CAUSE 3. Fan Motor 4. Auger Motor(s) 1. W ...

  • Bunn CDS-3 - page 21

    21 Auger Motors ....................................................................................................22 Auger Motor Capacitors ....................................................................................23 Auger Shaft Assembly .......................................................................................24 Auger ON/O ...

  • Bunn CDS-3 - page 22

    22 4. Disconnect the auger motor terminal from the terminal on the main wiring harness. 5. Remove the three remaining #8 locking screws securing the auger motor mounting bracket to cooling drum mounting bracket. 6. Rem ove moto r with mou nting brack et, drip tra y , split pin and torsion spring bearing as an assembly . NOTE: When removing or insta ...

  • Bunn CDS-3 - page 23

    23 FIG. 4 AUGER MOTOR CAP ACITOR TERMINALS SERVICE (CONT .) AUGER MOTOR CAP ACITOR FIG. 3 AUGER MOTOR CAP ACITORS P1341 Location: The auger motor capacitors are located on the lower right side of the auger motor mounting bracket inside the auger motor covers. T est Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the wir ...

  • Bunn CDS-3 - page 24

    24 SERVICE (cont.) AUGER SHAFT ASSEMBL Y Auger Shaft Assy Auger Shaft Bushing Cooling Drum Seal Auger Shaft Seal Hopper Drum Seal FIG. 5 AUGER SHAFT ASSEMBL Y Location: The Auger Shaft Assembly is located in each of the cooling drums. Removal and Replacement: 1. Drain, remove and clean hopper; refer to the Rec- ommended Daily Weekly Cleaning Sectio ...

  • Bunn CDS-3 - page 25

    25 SERVICE (cont.) AUGER SHAFT ASSEMBL Y(cont.) FIG. 6A AUGER SHAFT BUSHING Lightly lube the bushing I.D. with M2550.0000 “Lubri- Film” Do NOT get any Lube on this surface P1759 FIG. 6B COOLING DRUM SEAL P1760 Open face of seal away from tool Cooling Drum Seal Seal Insertion T ool FIG. 6C MOTOR/SHAFT ASSEMBL Y P1761 Lube about 1 1/2” of shaft ...

  • Bunn CDS-3 - page 26

    26 If continuity is present as described, the auger switch is operating properly . If continuity is not present as described, replace the auger switch. Removal and Replacement: 1. Pull the dispenser drawer out until the drawer hits the drawer stop. Using a screwdriver gently pr y up on the drawer stop and remove the drawer from the dispenser . 2. R ...

  • Bunn CDS-3 - page 27

    27 R22 FIG.9CIRCUITBREAKER P1342 SERVICE (cont.) CIRCUIT BREAKER Location: The circuit breaker is located inside the dispenser on the upper left side of the component bracket. T est Procedures: 1. Disconnect the dispenser from the power source. 2. Remove the wires from the circuit breaker . 3. Check for continuity between the terminals. Co ...

  • Bunn CDS-3 - page 28

    28 R22 R22 R22 120V COMPRESSORS SERVICE (cont.) COMPRESSOR & COMPONENTS (CDS-2) FIG. 11 COMPRESSOR ASSY 3 2 5 6 FIG. 12 COMPRESSOR ELECTRICAL COMPONENTS P1344 T est Procedures: WARNING: The compressor start capacitor must be properly discharged before proceeding. Compressor Start Relay: Refer to FIG. 12 1. Disconnect the dispenser from the powe ...

  • Bunn CDS-3 - page 29

    29 SERVICE (cont.) COMPRESSOR & COMPONENTS (CDS-2) (cont.) Compressor Start Capacitor: 1. Check for continuity across the terminals on the compressor start capacitor . If continuity is present as described, the start capacitor is operating properly . If continuity is not present as described, replace the capacitor . NOTE: If al l th e el ect ri ...

  • Bunn CDS-3 - page 30

    30 Compressor Thermal Overload Protector (230V): Refer to FIG. 12 1. Remove terminal cover retainer (6) and terminal cover (5). 2. Disconnect the black wire from the thermal overload protector . 3. Pull thermal overload protector off of the compressor pin and discard. 4. Push new thermal overload protector onto the com- pressor pin. 5. Refer to Fig ...

  • Bunn CDS-3 - page 31

    31 SERVICE (cont.) COMPRESSOR & COMPONENTS (CDS-3) FIG. 16 COMPRESSOR & COMPONENT LOCA TIONS FIG. 17 COMPRESSOR THERMAL OVERLOAD PROTECTOR LOCA TION 3. Disconnect the black wire to the thermal overload protector (4), the white and black or red wires to the compressor . 4. With a voltm eter , check voltag e across the blac k wire removed fro ...

  • Bunn CDS-3 - page 32

    32 SERVICE (cont.) COMPRESSOR & COMPONENTS (CDS-3) (cont.) Compressor Run Capacitor: 1. Check for continuity across the terminals on the compressor run capacitor . If continuity is present as described, the run capacitor is operating properly . If continuity is not present as described, replace the capacitor . NOTE: If all the electrical compon ...

  • Bunn CDS-3 - page 33

    33 SERVICE (cont.) COMPRESSOR & COMPONENTS (CDS-3) (cont.) Compressor Thermal Overload Protector: Refer to FIG. 17 1. Remove terminal cover retainer (7) and terminal cover (6). 2. Remove the wire from thermal overload protector from the compressor wiring harness to the thermal overload protector . 3. Remove overload protector retainer (5) and t ...

  • Bunn CDS-3 - page 34

    34 SERVICE (cont.) CONT ACTOR - ELECTRONIC CONTROL 6. Disconnect the black wires from contactor termi- nals #6 & #8 (#5 & #6, CDS-3 first type contac- tor). 7. With ON/OFF switch in the “ON” position, connect the dispenser to the power source and check for continuity across terminals on contactor . If conti nuity is not pres ent as des ...

  • Bunn CDS-3 - page 35

    35 SERVICE (cont.) COOLING DRUM ALIGNMENT The “A” shaped Cooling Drum Shipping Supports, removed during Initial Set-Up should be kept and used as a tool to reset the alignment of the cooling drums should it ever be required. Symptoms: Squeaky Operation, hopper lifts or won’t seat properly , hopper is pushed to one side or the other . T o chec ...

  • Bunn CDS-3 - page 36

    36 SERVICE (cont.) DA Y/NIGHT SWITCH If continuity is present as described, the day/night switch is operating properly . If continuity is not present as described, replace the day/night switch. Removal and Replacement: 1. Pull the dispenser drawer out until the drawer hits the drawer stop. Using a screwdriver gently pr y up on the drawer stop and r ...

  • Bunn CDS-3 - page 37

    37 FIG. 28 DISPENSER ON/OFF SWITCH TERMINALS P1337 SERVICE (cont.) DISPENSER ON/OFF SWITCH FIG. 27 ON/OFF SWITCH - DISPENSER P1343 Location: The dispenser ON/OFF switch is located inside the dispenser drawer on the left front of the control panel. T est Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the black wire from ...

  • Bunn CDS-3 - page 38

    38 R22 FIG. 29 ELECTRONIC CONTROL Location: The electronic control is located on the outside of the component bracket inside the chassis on the right side. T est Procedure: 1. Disconnect the dispenser from the power source. 2. Disconnect the plug from the main harness from the connector on the electronic control. 3. Wit h a voltm ete r , chec k the ...

  • Bunn CDS-3 - page 39

    39 R22 SERVICE (cont.) F AN FIG. 30 F AN P1342 Location: The fan is located inside the dispenser chassis just in front of the condenser . T est Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the yellow and white/black wires from the main harness to the fan leads. 3. With a volt meter , chec k the voltag e across the ye ...

  • Bunn CDS-3 - page 40

    40 SERVICE (cont.) FUSE AND FUSE HOLDER R22 FIG. 33 FUSE HOLDER P1342 Location: The fuse holder is located inside the dispenser on the upper left side of the component bracket just below the circuit breaker . T est Procedures: 1. Disconnect the dispenser from the power source. 2. Remove cap and fuse from fuse holder . 3. Remove fuse from the cap. 4 ...

  • Bunn CDS-3 - page 41

    41 SERVICE (cont.) ICE/OFF/NO ICE SWITCHES FIG. 36 ICE/OFF/NO ICE SWITCH TERMINALS P1334 FIG. 35 ICE/OFF/NO ICE SWITCHES P1343 Location: The ICE/OFF/NO-ICE switches are located inside the dispenser drawer . T est Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the black wire from the switch to be tested and white/black ...

  • Bunn CDS-3 - page 42

    42 SERVICE (cont.) LAMP CORD ASSY FIG. 37 LAMP CORD ASSY P1343 Location: The lamp cord assembly is located in the left top of the auger motor cover . T est Procedures: 1. Disconnect the dispenser from the power source. 2. Unplug the lamp cord assembly from lamp cord connector assembly . 3. Check for continuity across the tip of the cord as- sembly ...

  • Bunn CDS-3 - page 43

    43 SERVICE (cont.) LAMP CORD CONNECTOR If continuity is not present when lamp cord assembly is connected or continuity is present when lamp cord assembly is not connected, replace the lamp cord connector . Removal and Replacement: 1. Disconnect the lamp cord assembly from the lamp cord connector . 2. Remove the two #8-32 locking screws securing the ...

  • Bunn CDS-3 - page 44

    44 Removal and Replacement: 1. Disconnect the lamp cord assembly from the lamp cord connector assembly in the top of the auger motor cover . 2. Remove the hopper cover with the lamp cord as- sembly from the hopper . 3. Remove hopper cover liner from the hopper cover . 4. Cut off the closed-end splices connecting lamp cord assembly to the lamp holde ...

  • Bunn CDS-3 - page 45

    45 SERVICE (cont.) L.E.D./ADJUSTMENT BOARD 3. Lift switch panel with wires and L.E.D. /adjust- ment board as an assembly and turn over . 4. Disconnect the connector on the dispenser wiring harness from the pin connector on the rear of the L.E.D./adjustment board. 5. Remove the #4 keps nut from the right rear stud on the control panel and remove the ...

  • Bunn CDS-3 - page 46

    46 R22 FIG.45 SOLENOID TERMINALS P1327 SERVICE (cont.) SOLENOIDS FIG. 44 SOLENOIDS P1342 Location: The solenoids are mounted on a bracket that is attached on top of the chassis on the left side. T est Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the white/black wire from the solenoid to be tested and the orange wire ...

  • Bunn CDS-3 - page 47

    47 FIG. 47 TEMPERA TURE SENSOR P1325 SERVICE (cont.) TEMPERA TURE SENSOR FIG. 46 TEMPERA TURE SENSOR P1341 Location: The temperature sensors are located inside the top rear of the cooling drum under the auger motor covers. T est Procedures: 1. Position the DA Y/NIGHT switch in the “NIGHT” position, check the L.E.D. on the control panel for fla ...

  • Bunn CDS-3 - page 48

    48 FIG. 49 TORQUE SENSOR CIRCUIT BOARD TERMINALS P1328 SERVICE (cont.) TORQUE SENSOR CIRCUIT BOARD FIG. 48 TORQUE SENSOR CIRCUIT BOARD P1341 Location: The torque sensor circuit board is located on the rear of the cooling drum mount just left of center . T est Procedures: 1. With the ON/OFF switch and Auger switch in the “ON” position and the IC ...

  • Bunn CDS-3 - page 49

    49 SERVICE (cont.) TRANSFORMER FIG. 51 TRANSFORMER TERMINALS P1329 R22 FIG. 50 TRANSFORMER P1342 Location: The transformer is located inside the chassis on the upper rear side of the component bracket. T est Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the plug from the transformer to the connector from the dispenser ...

  • Bunn CDS-3 - page 50

    50 SERVICE (CONT .) VOL T AGE DIVIDER (P AF Models only) Location: The voltage divider is located in the wiring har - ness, inside the chassis near the upper rear side of the component bracket. T est proceedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the four -pin plug of the main harness from the four -pin plug on the vo ...

  • Bunn CDS-3 - page 51

    51 COOLANT SCHEMA TIC DIAGRAM CDS-2 27646 022500 ...

  • Bunn CDS-3 - page 52

    52 COOLANT SCHEMA TIC DIAGRAM CDS-3 (Prior to S/N CDS 0019500) LEFT EV APORA TO R CENTER EV APORA TO R CONDENSER SUCTION ACCUMULA TO R COMPRESSOR RIGHT EV APORA TO R 28575.0000A 1/98 ©1998 Bunn-O-Matic Corporation CDS-3 COOLANT SCHEMA TIC SPLITTER FIL TER DRYER s s s AEV AEV AEV HOT GAS BY -P ASS VA LV E SOLENOID 27646 022500 ...

  • Bunn CDS-3 - page 53

    53 LEFT EV APORA TO R CENTER EV APORA TO R CONDENSER SUCTION ACCUMULA TO R COMPRESSOR RIGHT EV APORA TO R 29428.0000A 12/98 ©1998 Bunn-O-Matic Corporation CDS-3 COOLANT SCHEMA TIC SPLITTER FIL TER DRYER s TEV TEV TEV s s SIGHT GLASS COOLANT SCHEMA TIC DIAGRAM CDS-3 (S/N CDS 0019500 - Up) 27646 022500 ...

  • Bunn CDS-3 - page 54

    54 27646 022500 ...

  • Bunn CDS-3 - page 55

    55 27646 022500 ...

  • Bunn CDS-3 - page 56

    56 WHI/RED RIGHT AUGER BLK RED WHI LEFT AUGER BLK RED WHI 1 4 WHI/BLK BLK WHI/BLK RED WHI/BLK RED-22 BLK-22 1 4 SOL LEFT ORA-22 WHI/GRN SCHEMA TICWIRINGDIAGRAM FOR CDS-2 P AF WHI/GRN WHI/GRN ON/OFF SW . GRN 27556.0002H 12/99 © 1996 BUNN-O-MA TIC CORPORA TION 120 VOL TS AC 2 WIRE SINGLE PHASE 60 HZ J4-1 J4-24 C O N T R O L B O A R D J4-5 J4-1 ...

  • Bunn CDS-3 - page 57

    57 WHI/BRN or VIO WHI/RED WHI/RED WHI/BLU WHI/BLU LT . AUGER SW . RT . AUGER SW . WHI/BRN RIGHT AUGER BLK RED WHI BLK BLK WHI/BLK LEFT AUGER BLK RED WHI WHI/BLK 1 4 WHI/BLK BLK WHI/BLK RED WHI/BLK RED-22 BLK-22 1 4 SOL LEFT ORA-22 WHI/GRN SCHEMA TICWIRINGDIAGRAM FOR CDSA-2 P AF WHI/GRN WHI/GRN ON/OFF SW . 27556.0003B 02/01 © 1996 BUNN-O-M AT ...

  • Bunn CDS-3 - page 58

    58 27646 022500 ...

  • Bunn CDS-3 - page 59

    59 27646 022500 ...

  • Bunn CDS-3 - page 60

    60 27646 022500 ...

Produzent Bunn Kategorie Beverage Dispenser

Dokumente, die wir vom Produzenten des Geräts Bunn CDS-3 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Bunn
- Bedienungsanleitungen CDS-3
- Produktkarten Bunn
- Informationsbroschüren
- oder Energieetiketten Bunn CDS-3
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Bunn CDS-3.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Bunn CDS-3, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Bunn CDS-3. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Bunn CDS-3 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Bunn CDS-3, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Bunn CDS-3 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Bunn CDS-3 verständlich ist.

Eine gänzliche Bedienungsanleitung von Bunn sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Bunn CDS-3 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Bunn CDS-3 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Bunn CDS-3, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Bunn CDS-3 - die uns die ersten Schritte während der Nutzung von Bunn CDS-3 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Bunn CDS-3 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Bunn CDS-3 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Bunn CDS-3?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bunn CDS-3 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bunn CDS-3 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)