Bedienungsanleitung Ingersoll-Rand 8506-A

18 Seiten 1.2 mb
Download

Zur Seite of 18

Summary
  • Ingersoll-Rand 8506-A - page 1

    OPERATOR’S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION MANUAL Released: M30 33 3-l-77 Tool Products Revised: l-27-95 “O” SERIES “QRT” SCREWDRIVERS Models: 8506-A( ), 8509-A( ), 8515-A( ) and 8521-A( ). 1018-2 READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE ...

  • Ingersoll-Rand 8506-A - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. I I Wear hearing protection when operating this tool. Turn off air supply and disconnect air supply hose before installing, . removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. A WARNING Do not carry the tool by the hose. Air powered ...

  • Ingersoll-Rand 8506-A - page 3

    ROUTINE LUBRICATION REQUIREMENTS M30 33 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not ...

  • Ingersoll-Rand 8506-A - page 4

    MODEL IDENTIFICATION MODELS WITH -EU SUFFIX ARE “EC” COMPLIANT MODELS. NOTE: GENERAL PURPOSE WRENCH 37167 FURNISHED WITH -A AND -T MODELS. DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air before performing maintenance or service to tool. DRIVE SECTION Remove clut ...

  • Ingersoll-Rand 8506-A - page 5

    DRIVE SECTION M30 ADJUSTABLE CLUTCH 33 CLUTCH ADJUSTMENT Remove clutch assembly (36310) from tool. Place pin in hole of jaw (36318) or wrench on square end of spindle (36311) to adjust nut (36313). To adjust properly, release nut to least tension. Tight- en nut one or two positions -each click = one position. Assemble clutch to tool and test torque ...

  • Ingersoll-Rand 8506-A - page 6

    DRIVE SECTION TORQMATIC CLUTCH CLUTCH ADJUSTMENT Remove clutch assembly from tool. Place wrench on square end clutch. Clutch assembly should contain approximately 1/8 oz. (3.5 of spindle (38322) to adjust nut (38313). To adjust properly, re- g) of grease. lease nut to least tension. Tighten nut one or two positions -each a. click = one position. As ...

  • Ingersoll-Rand 8506-A - page 7

    ...

  • Ingersoll-Rand 8506-A - page 8

    GEARING SECTION DRIVE GEARING DISASSEMBLY a. b. Remove spindle and components from ring gear. To remove gears from spindle, remove bearing, spacer and shafts. ASSEMBLY NOTE: Pack bearings and lubricate gears liberally with ARO 33153 grease upon assembly. Gearing assembly should contain approximately 1/8 oz. (3.5 g) of grease. a. Assemble spacer (33 ...

  • Ingersoll-Rand 8506-A - page 9

    GEARING SECTION M30 AUXILIARY GEARING 33 DISASSEMBLY a. Grasp adapter (ring gear) in one hand and tap splined end of spindle with a soft face hammer; spindle and components will 33153 grease upon assembly. Gearing should contain approxi- loosen from adapter. mately 118 oz. (3.5 g) of grease. a. b. To remove gears from spindle, remove bearing, space ...

  • Ingersoll-Rand 8506-A - page 10

    MOTOR SECTION DISASSEMBLY a. Remove motor from housing. Grasp cylinder in one hand and tap splined end of rotor with a soft face hammer; motor will assemble over rotor, aligning air inlet holes of cylinder with air come apart. inlet slots of end plate. d. Coat blades (31363) with ARO 29665 spindle oil and as- ASSEMBLY semble to rotor slots - straig ...

  • Ingersoll-Rand 8506-A - page 11

    HEAD SECTION M30 33 DISASSEMBLY a. Remove roll pin (Y178-25), releasing trigger (45469). b. Remove screw (Y222-156-C) releasing shroud (45468). c. Grasp end of valve assembly (47880) and pull to remove valve assembly and bushing (45465). d. Remove retaining ring (Y147-68), releasing screens (42911) and muffler (45474). ASSEMBLY NOTE: Whenever a par ...

  • Ingersoll-Rand 8506-A - page 12

    QTY 1 1 5 6 1 1 1 2 1 PART NUMBER 31092 31093 31363 36317 41795 41799 41954 42911 45474 SERVICE KIT NO. 42114 FOR SERVICING ADJUSTABLE CLUTCH MODELS DESCRIPTION SPRING THRUST PIN BLADE PIN MOTOR OIL GEAR LUBE “O” RING LUBE SCREEN MUFFLER PART QTY NUMBER 6 Y16-205 1 Y147-68 1 Y178-25 2 Y180-13 2 Y325-7 2 Y325-11 2 Y325-12 2 Y325-13 SERVICE KIT N ...

  • Ingersoll-Rand 8506-A - page 13

    ACCESSORIES 44361-( ) PIPED EXHAUST SYSTEM ASSEMBLY M30 33 30302-( ) INLET HOSE - 5/16” I.D. 1/4” P.T.F. THREAD P.T.F. THREAD TO AIR SUPPLY 46672-l ADAPTER ASSEMBLY 2622 HOSE ADAPTER 3/8” MALE N.P.T.F. 1/2” I.D. 43551-6 MUFFLER 3/8” FEMALE N.RT.F. PIPED EXHAUST ASSEMBLY CONSISTS OF 5/16” I.D. AIR INLET HOSE WlTH IN” MALE FlTTlNG AT EA ...

  • Ingersoll-Rand 8506-A - page 14

    ACCESSORIES HOUSING AND ADAPTER ASSEMBLIES FlNDER ADAPTER IS PRESSED INTO HOUSING. FINDER ADAPTER 39332 HOUSING ASSEMBLY HOUSlNG AND FINDER ADAPTER -USE WITH FlNDERS 36106-(), 36105-(), 41292-() AND 41292-(). ALSO USE WITH GUIDES 30334-(), 40261 AND 41767. ALSO FOR USE WITH BALL LOCK ADAPTER ASSEMBLY 44699 WITHOUT USE OF GUIDE BUSHING. . ASSEMBLY N ...

  • Ingersoll-Rand 8506-A - page 15

    ACCESSORIES FINDERS EXTENSION FINDER FOR 1/4” HEX BITS M30 33 NOTE: SPRING 30111 AND LOCK SPRING 31574 REQUIRED FOR USE WITH FINDERS (ORDER SEPARATELY). USE WITH FINDER ADAPTER 36332. BELL MOUTH FINDER FOR 1/4” HEX BITS Similar to standard finders except that each finder will accept mm sizes and types of screw heads. NOTE: SPRING 36111 AND LOCK ...

  • Ingersoll-Rand 8506-A - page 16

    ACCESSORIES BITS AND BIT HOLDERS 1/4” HEX DRIVE BITS EXTENSION BLADED BITS FOR SLOTTED SCREWS. PART NO. LENGTH POINT SIZE SHAFT DIA. 30320-l 1-15/16” 1 .182” 30320-2 1-15/16” 2 .246” PHILLIPS BITS 30320-3 1-15/16” 3 .310” 31531-1 2-3/4” 1 .182” 31531-2 2-3/4” 2 .246” 315313 2-3/4” 3 .310” REED & PRINCE BITS . PART NO. ...

  • Ingersoll-Rand 8506-A - page 17

    SOCKET HEAD DRIVERS MAGNETIC BIT HOLDER USE WITH GUIDE BUSHING 46261. SQUARE DRIVE ADAPTERS USE WITH GUIDE BUSHING 30334-( ). ACCESSORIES M30 BITS AND BIT HOLDERS 33 HEX BALL LOCK ADAPTER PART NO. LENGTH HEX SETSCREW CAP SCREW SHAFT DIA. SIZE SIZE SIZE 30370-2 3/32” #10-#12 #4-#5 .187” 30370-3 1/8” 1/4 .187” 30370-4 5/32” 5/16 #10 .187” ...

  • Ingersoll-Rand 8506-A - page 18

    PN 49999-032 ...

Produzent Ingersoll-Rand Kategorie Power Screwdriver

Dokumente, die wir vom Produzenten des Geräts Ingersoll-Rand 8506-A erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Ingersoll-Rand
- Bedienungsanleitungen 8506-A
- Produktkarten Ingersoll-Rand
- Informationsbroschüren
- oder Energieetiketten Ingersoll-Rand 8506-A
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Ingersoll-Rand 8506-A.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Ingersoll-Rand 8506-A, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Ingersoll-Rand 8506-A. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Ingersoll-Rand 8506-A ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Ingersoll-Rand 8506-A, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Ingersoll-Rand 8506-A hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Ingersoll-Rand 8506-A verständlich ist.

Eine gänzliche Bedienungsanleitung von Ingersoll-Rand sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Ingersoll-Rand 8506-A bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Ingersoll-Rand 8506-A befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Ingersoll-Rand 8506-A, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Ingersoll-Rand 8506-A - die uns die ersten Schritte während der Nutzung von Ingersoll-Rand 8506-A erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Ingersoll-Rand 8506-A hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Ingersoll-Rand 8506-A im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Ingersoll-Rand 8506-A?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ingersoll-Rand 8506-A nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ingersoll-Rand 8506-A hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)