-
Bunn FCD-4 - page 1
BU N N ® INST ALLA TION & OPERA TING MANU AL FCD-4 33496.0000 03/01 ©2000 Bunn-O-Matic Corporation BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .bunnomatic.com ...
-
Bunn FCD-4 - page 2
2 W ARRANTY Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects in material and workmanship existing at the time of manufacture and appearing within one year from the date of installation. In addition: 1.) Bunn warrants electronic circuit and/or control boards to be commercially free from d ...
-
Bunn FCD-4 - page 3
3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 00986.0002 33461.0000 ! W ARNING DO NO T O VERLOAD CIRCUIT . AL W A YS ELECTRICALL Y GROUND THE CHASSIS OR AD APT OR PLU ...
-
Bunn FCD-4 - page 4
4 INITIAL SET -UP CAUTION: The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser. Place the dispenser on a sturdy counter or shelf able to support at least 250 lbs. (113.4 kg). The FCD-4 is designed for indoor use only. 1. Set the dispenser on the counter where it will be used. The FC ...
-
Bunn FCD-4 - page 5
5 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WATER system with operating pressure between 20 and 100 psi (138 and 690 kPa). This water source must be capable of producing a minimum flow rate of 3 fluid ounces (88.7 milliliters) per second. A shut off valve should be installed in the line before the dispenser. Install a regulat ...
-
Bunn FCD-4 - page 6
6 OPERA TING CONTROLS Refrigeration Switch The refrigeration switch is located on the top of the dispenser near the left rear corner. This switch controls power to the compressor and the condenser fan motor. Sanitize Switch The sanitize switch is located behind the drip tray in the lower left corner of the chassis. The drip tray can be removed to p ...
-
Bunn FCD-4 - page 7
7 OPERATING CONTROLS (cont.) FIG 5 Press and Hold Models A. Product Dispense Switch Pressing and holding switch will initiate product flow from the respective nozzle; releasing the switch will stop the flow. B. Chilled Water Dispense Switch Pressing and holding switch will initiate chilled water flow from the nozzle; releasing the switch will stop ...
-
Bunn FCD-4 - page 8
8 INITIAL FILL CAUTION: The dispenser must be disconnected from the power source throughout the initial fill except when specified in the instructions. 1. Remove drip tray assembly and splash panel from the dispenser. 2. Pull the overflow tube from its retaining clip and place the end into an empty 64 fluid ounce (2 liter) container. 3. Ensure that ...
-
Bunn FCD-4 - page 9
9 INITIAL FILL (cont) Ambient Concentrates (Optional) 1. Install an Ambient Concentrate Conversion Kit (BUNN-O-MATIC part number 33699.0000) per the instructions provided in the kit. 2. Attach the concentrate product hose to the appropriate concentrate line located behind the dispenser’s splash panel. 3. Attach the other end of the product hose t ...
-
Bunn FCD-4 - page 10
10 DISPENSER USE Press and Hold Models (Refer to Fig 5) 1. Place a cup on the drip tray beneath the desired dispensing nozzle. 2. Press and hold the “Product Dispense” or “Chilled Water” switch until the beverage/water reaches the desired level, then release. Portion Control Models (Refer to Fig 6) 1. Place a cup on the drip tray beneath th ...
-
Bunn FCD-4 - page 11
11 CLEANING & PREVENTIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The Bunn Juice Dispenser incorporates a rinse reminder feature which lights the rinse led on the front panel when it is time to rinse. See dip switch function list to activate this feature. Daily: Rinse Procedure Tools required: 32 oz. (946 ml) minimum empty c ...
-
Bunn FCD-4 - page 12
12 CLEANING (cont) portion contol dispensers. The “REFILL” indicator will light and the beeper will sound for the dispense head selected. 7. Once the dispense heads have been selected, press and hold the “Sanitize Switch” for 5 seconds again to initiate the automatic cycle. (When the cycle is initiated the “SANITIZE” indicator lights st ...
-
Bunn FCD-4 - page 13
13 Monthly: Clean Condenser Air Filter 1. Remove the condenser air filter located on the rear of the dispenser. 2. Using a water spray, clean the air filter. Annually: Replace Pump Tubing 1. Open dispenser door. 2. Remove all product containers and place them in a refrigerated (35-40 degrees F [1.6-4.4 degrees C]) environment. Disconnect all connec ...
-
Bunn FCD-4 - page 14
14 ADJUSTMENT & OPTIONAL SETTINGS SETTING THE MIX RATIO/BRIX Ratio Cup Method 1. Adjust the water flow as described in Water Flow Testing and Adjustment. 2. Remove the dispense nozzle from the appropriate dispense position. 3. Assemble, lubricate, and install the Flow Separator Assembly (BUNN-O-MATIC part number 32629.0000) into the dispense no ...
-
Bunn FCD-4 - page 15
15 Water Flow T esting and Adjustment 1. Enter the “Pump Speed Programming” mode by simultaneously press- ing both “Hidden Switches” Fig 5 or Fig 6. Note that the beeper sounds twice and that the “PROGRAM” indicator begins flashing. 2. Place a graduated measuring cup or the large chamber of the empty brixing cup (BUNN-O-MATIC part numbe ...
-
Bunn FCD-4 - page 16
16 that each step is confirmed by a single flash of the appropriate “REFILL” indicator and a single tone from the beeper. 4. Repeat as necessary at the remaining dispense stations. 5. Exit the “Pump Speed Programming” mode by simultaneously pressing both “Hidden Switches”. Note that the beeper sounds twice and that the “PROGRAM” ind ...
-
Bunn FCD-4 - page 17
17 b) In a 5 second period, press and release the “Chilled Water Switch” the number of times that you want the password set to (maximum of 10.) For example: If you want the password set to 3, press and release the “Chilled Water Switch” 3 times in the 5 second period. c) Release the “Hidden Switch”. d) At the end of the 5 second period, ...
-
Bunn FCD-4 - page 18
18 Password Protection The programming modes and service lockout function may be password protected to prevent accidental or unauthorized access to these features. The dispenser is shipped from the factory with a password of “0” (no password.) 1. Enter the “Pump Speed Programming” mode by simultaneously pressing both “Hidden switches”. ...
-
Bunn FCD-4 - page 19
19 Dispense Fault List “REFILL” indicator Beeper Fault 2 flashes 2 beeps Dispense station locked out. 3 flashes 3 beeps DISPENSE/RINSE sensing fault. 4 flashes 4 beeps DISPENSE/RINSE knob mis-positioned. 5 flashes 5 beeps Pump motor stalled/speed sensor inoperative. All “REFILL” 3 beeps Dispenser locked out. indicators flash 3 times Dip Swi ...
-
Bunn FCD-4 - page 20
20 COOLANT SCHEMA TIC DIAGRAM CONDENSER SUCTION ACCUMULA TOR COMPRESSOR EV APORA T OR PROCESS TUBE 33464.0000A 09/00 ©2000 Bunn-O-Matic Corporation FIL TER DR YER 33496 011101 ...
-
Bunn FCD-4 - page 21
21 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 RIGHT LAMP ASSY. LEFT LAMP ASSY. GRN GRN GRN N L1 BLU BRN/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOSTAT K COMP. K COMPRESSOR ASSEMBLY + – RECT TRANSFORMER WHI/BLU WHI WHI WHI WHI/RED WHI/RED BLK BLU BLU RED/BLK RED/BLK GRY WHI WHI WHI ...
Haben Sie eine Frage bezüglich Bunn FCD-4?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bunn FCD-4 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bunn FCD-4 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.