Bedienungsanleitung Lava Computer 650

20 Seiten 0.11 mb
Download

Zur Seite of 20

Summary
  • Lava Computer 650 - page 1

    La v aP ort 650 Installation Manual Rev . B01 LAV A COMPUTERS SSERIAL PCI P .N. MOKO L74.1 MADE IN CANADA PNMOKO S-1 MADEIN JAPAN 0255351 ...

  • Lava Computer 650 - page 2

    C ontents Quick Install Installing the LavaP ort-650 Hardware Windows Installation · Changing I/O Resources - Com & IRQ · Setting LavaP ort Data R ates · Lava Modem Speed Set - f or 230.4 kbps · Setting LavaP ort FIFO Control · Flow C ontrol Windows NT 4.0 Installation · High Speed Data Rates 3 4 5 8 10 12 14 16 17 18 Note: Instructions f ...

  • Lava Computer 650 - page 3

    Quick Install Windo ws 95/98/ME/2000/XP 1. With the power off , insert the LavaP ort-650 PCI card into any free PCI slot. 2. Launch Windows - new hardware will be detected . 3. When prompted , inser t the LavaP ort-650 installation diskette point Windows to look at the floppy's root directory . 4. After Windows has booted , click the Star t bu ...

  • Lava Computer 650 - page 4

    Hardwar e Installation 4 1. Before opening the casing of y our computer , make sure that all power is off . 2. Locate an unused PCI slot and insert the LavaP ort-650 into it. Ensure that it is well seated . 3. Screw the metal backplane of the LavaP ort-650 board to your PC’ s casing and replace the machine ’ s c over . 4. Connect your modem cab ...

  • Lava Computer 650 - page 5

    Windo ws Driver Installa tion 1. Once the Lav aPort-650 is installed in your PC, start your computer . Windows will automatically detect the Lav aPort-650 as a new PCI Serial Controller and ask you t o inser t the LavaP ort Installation diskette. The installation files are located in the root directory of this disk. 2. After the necessary files hav ...

  • Lava Computer 650 - page 6

    6 3. Click on the Start button, then choose S ettings, Control Panel, System, Device Manager . Y ou should see a window that is similar to the following: ...

  • Lava Computer 650 - page 7

    4. Click on Ports and select the Com port listed under the heading LavaP or t 650 PCI. 5. Click Properties. The following screen will appear: 7 ...

  • Lava Computer 650 - page 8

    8 Because the LavaP or t 650 is a PCI device, Windows will alwa ys allocate non-standard I/O resources t o this por t (e.g . Assigning it as Com 5, even though any one of Com1-4 ma y be free). If your software requires the use of standard I/O resources , you may modify those used by the LavaP or t-650 in one of two ways: Click on the Resources T ab ...

  • Lava Computer 650 - page 9

    9 1. Y ou may physically modify the I/O Range and IRQ used by the LavaP or t 650 by de-selecting the “Use Automatic Settings” check box, and double-click ing the appropriate heading , or : 2a. F or Windo ws95/98/ME, you may use the La va P or t Redirect Utility provided in the Utils subdirectory of your Lav aPort diskette. This utility may be r ...

  • Lava Computer 650 - page 10

    10 Setting Lav aP or t Data Rates in Window s ...

  • Lava Computer 650 - page 11

    11 The data rate of the La vaP or t may be set using the Bits per Second pull down menu. Please note that this menu will also appear when setting the “Port Properties” in any c ommunications application, and may have to be set independently of your Contr ol Panel settings. Control P anel settings may not necessarily be linked to those of your C ...

  • Lava Computer 650 - page 12

    The Lav aPort-650 suppor ts data rates up to 460.8 kbps, including 115.2 kbps and 230.4 k bps. However , not all modems suppor t Com P or t rates above 115.2 kbps. If your modem does not support higher data rates and you select a higher data rate in the La vaPort Properties, Windows will automatically default to the slowest supported rate in the ch ...

  • Lava Computer 650 - page 13

    13 ...

  • Lava Computer 650 - page 14

    14 Setting Lav aP or t FIFO C ontrol in Windo ws ...

  • Lava Computer 650 - page 15

    The Lav aPort-650 uses a 16650 U ART incorporating a 32-byte FIFO (first- in first-out) buffer . The FIFO control tabs set the buff er “trigger ” levels. When the buffer is filled to its trigger level with the selected number of bytes , the CPU will be interrupted and asked to either reload the buff er (for transmission), or retrieve data from ...

  • Lava Computer 650 - page 16

    Flow C ontrol refers to the type of signaling that is used between the modem and the LavaP or t. If you are connecting the Lav aPort to a modem or ISDN terminal adapter , use the default setting of Hardware (RTS/CTS) flow control. Software Flow Contr ol (Xon/Xoff ) is used only for connecting the LavaP or t to a non-modem serial device (e.g . Using ...

  • Lava Computer 650 - page 17

    17 Windo ws NT 4.0 Installation Windo ws NT Driver Installa tion 1. Once the Lav aPort-650 is installed in your PC, turn your computer on and start NT . 2. Place the Lav aPort installation diskette into your floppy drive and select Run from the Star t Menu. When prompted type: A:NT4.0Setup. 3. After the necessary files have been copied , select M ...

  • Lava Computer 650 - page 18

    18 Please note that Com 1 ma y not appear in this applet if you have y our mouse attached to Com 1. The Lav aPort-650 suppor ts data rates up to 460.8 kbps, including 115.2 kbps and 230.4 k bps. However , not all modems suppor t Com P or t rates above 115.2 kbps. If your modem does not suppor t higher data rates and you select a higher data rate in ...

  • Lava Computer 650 - page 19

    19 This page intentionally blank ...

  • Lava Computer 650 - page 20

    La va C omputer MFG Inc. La v a T echnical Suppor t 9:00 am to 5:30 pm Monday t o Frida y (Eastern Time) T el: +416 674-5942 F ax: + 416 674-8262 E-mail: tech@lav alink.com Internet: www .lavalink.c om This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device ma y not cause harmful interfe ...

Produzent Lava Computer Kategorie Computer Hardware

Dokumente, die wir vom Produzenten des Geräts Lava Computer 650 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Lava Computer
- Bedienungsanleitungen 650
- Produktkarten Lava Computer
- Informationsbroschüren
- oder Energieetiketten Lava Computer 650
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Lava Computer 650.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Lava Computer 650, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Lava Computer 650. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Lava Computer 650 ansehen.

Die komplette Bedienungsanleitung des Geräts Lava Computer 650, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Lava Computer 650 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Lava Computer 650 verständlich ist.

Eine gänzliche Bedienungsanleitung von Lava Computer sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Lava Computer 650 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Lava Computer 650 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Lava Computer 650, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Lava Computer 650 - die uns die ersten Schritte während der Nutzung von Lava Computer 650 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Lava Computer 650 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Lava Computer 650 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Lava Computer 650?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Lava Computer 650 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Lava Computer 650 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)