Deutsch dropdown-ico

Bedienungsanleitung Axis Communications P3363-V

61 Seiten 1.76 mb
Download

Zur Seite of 61

Summary
  • Axis Communications P3363-V - page 1

    USER MANUAL AXIS P3363–V Network Camera ...

  • Axis Communications P3363-V - page 2

    About this Document This manual is intended for administrators and users of the AXIS P3363–V Fixed Dome Network Camera, and is applicable to rmware 5.40 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linu ...

  • Axis Communications P3363-V - page 3

    This product complies with the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS). China This product complies with the requirements of the legislative act Administration on the Control of Pollution Caused by Electronic Information Products (ACPEIP). Suppo ...

  • Axis Communications P3363-V - page 4

    AXIS P3363–V Network Camera Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Axis Communications P3363-V - page 5

    AXIS P3363–V Network Camera Table of Contents Symptoms, Possible Causes and Remedial Actions . . . . . . . . . . . . . . . . . . . . . 55 Technical Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Performance Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Axis Communications P3363-V - page 6

    AXIS P3363–V Network Camera Hardware Overview Hardware Overview 2 1 3 4 5 6 7 8 9 11 1 0 1 2 1 3 1. Camera unit 2. Network connector (PoE) 3. Audio out 4. LED indicators 5. Audio in 6. I/O connector 7. Control button 8. Fan output connector 9. SD memory card slot 10. Network cable 11. Camera unit 12. Dome cover 13. Tamper-proof screws Connectors ...

  • Axis Communications P3363-V - page 7

    AXIS P3363–V Network Camera Hardware Overview Network connector - RJ45 Ethernet connector. Supports Power over Ethernet (PoE). NOTICE NOTICE NOTICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specic use. Make sure tha ...

  • Axis Communications P3363-V - page 8

    AXIS P3363–V Network Camera Hardware Overview Note • The Status LED can be congured to be unlit during normal operation. To congure, go to Setup > System Options > Ports & Devices > LED . See the online help for more information. • The Status LED can be congured to ash while an event is active. • The Status LED can ...

  • Axis Communications P3363-V - page 9

    AXIS P3363–V Network Camera Accessing the Product Accessing the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating system ...

  • Axis Communications P3363-V - page 10

    AXIS P3363–V Network Camera Accessing the Product Access from the Internet Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must congure your network router to allow incoming data trafc to the product. To do this, enable the NAT-traversal feature, which will attempt to a ...

  • Axis Communications P3363-V - page 11

    AXIS P3363–V Network Camera Accessing the Product When using 50 Hz, the maximum frame rate is limited to 25 fps. Note Power line frequency is different in different geographic regions. In the Americas, 60 Hz is usually used; most other parts of the world use 50 Hz. Local variations may apply, always check with the local authorities. The Live View ...

  • Axis Communications P3363-V - page 12

    AXIS P3363–V Network Camera Accessing the Product Click the View Full Screen button and the video image will ll the entire screen. Press ESC (Escape) on the computer keyboard to cancel full screen view. The Record button is used to record the current video stream. The location where the recording is saved can be specied in the AMC Control P ...

  • Axis Communications P3363-V - page 13

    AXIS P3363–V Network Camera Accessing the Product Pan and Tilt bars – Use the arrows to pan and tilt the camera view, or click on a position on the bar to steer the camera view to that position. Zoom bar – Use the arrows to zoom in and out, or click on a position on the bar to zoom to that position. The PTZ controls can be disabled under PTZ ...

  • Axis Communications P3363-V - page 14

    AXIS P3363–V Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream ...

  • Axis Communications P3363-V - page 15

    AXIS P3363–V Network Camera Media Streams The AMC Control Panel can be used to congure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on rst use, after which it can be congured. Open the AMC Control Panel from: • Windows Control ...

  • Axis Communications P3363-V - page 16

    AXIS P3363–V Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this. Accessing Audio Streams The Live View p ...

  • Axis Communications P3363-V - page 17

    AXIS P3363–V Network Camera Setting Up the Product Setting Up the Product The Axis product can be congured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to ...

  • Axis Communications P3363-V - page 18

    AXIS P3363–V Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can congure the following: • Video stream settings. See page 18 . • Stream proles. See page 19 . • Camera settings. See page 20 . • View area. See page 21 . • Overlay image. See page 22 . ? ...

  • Axis Communications P3363-V - page 19

    AXIS P3363–V Network Camera Video and Audio • Compression . The compression level affects the image quality, bandwidth and le size of saved images; the lower the compression, the higher the image quality with higher bandwidth requirements and larger le sizes. • Rotate image . If required, the image can be rotated. • Mirror . If requir ...

  • Axis Communications P3363-V - page 20

    AXIS P3363–V Network Camera Video and Audio Camera Settings The Video & Audio > Camera Settings page provides access to advanced image settings for the Axis product. Image Appearance Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation. The value 0 gives a black and white image. The image ...

  • Axis Communications P3363-V - page 21

    AXIS P3363–V Network Camera Video and Audio Set Shutter to • Auto to set the shutter speed automatically. If required, use Max shutter to limit the shutter speed to prevent the frame rate from being reduced. For example, to get 30 fps, set Max shutter to 1/30. • Fixed to use a xed shutter speed. Gain , measured in decibel (dB), is the amou ...

  • Axis Communications P3363-V - page 22

    AXIS P3363–V Network Camera Video and Audio To enable a view area, go to Video & Audio > Camera Settings and select Enable View Area . To congure the view area: 1. Go to Video & Audio > View Area . 2. Select an Aspect ratio and a Video stream resolution . 3. Use the mouse to move and resize the view area. 4. Select Enable PTZ to ...

  • Axis Communications P3363-V - page 23

    AXIS P3363–V Network Camera Video and Audio 5. Click Save . To display the overlay image: 1. Go to Video & Audio > Video Stream and select the Image tab. 2. Under Overlay Settings , select Include overlay image at the coordinates and enter the X and Y coordinates. 3. Click Save . For information about supported image formats, see the onlin ...

  • Axis Communications P3363-V - page 24

    AXIS P3363–V Network Camera Video and Audio 5. When satised, click Enable iris to enable the iris. The Pixel counter shows the number of pixels in an area of the image and can be used to ensure that the size of the image fullls certain requirements, for example for face recognition. Use the mouse to move and resize the pixel counter, or ent ...

  • Axis Communications P3363-V - page 25

    AXIS P3363–V Network Camera Video and Audio • G711 is an unlicensed standard codec that is useful when integrating audio into a VoIP system • G726 is an unlicensed speech codec that is most commonly used within the security industry. The Sample rate denes the number of times per second the sound is sampled. A higher sample rate will provid ...

  • Axis Communications P3363-V - page 26

    AXIS P3363–V Network Camera Live View Cong Live View Cong You can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 19 . • Default Viewer for Browser. See page 26 . • Viewer Settings. See page 27 . • Action Buttons. ...

  • Axis Communications P3363-V - page 27

    AXIS P3363–V Network Camera Live View Cong Browser Viewer Description AMC Recommended viewer in Internet Explorer (H.264/Motion JPEG). QuickTime H.264. Java applet A slower imaging alternative to AMC (Motion JPEG). Requires one of the following installed on the client: • JVM (J2SE) 1.4.2 or higher. • JRE (J2SE) 5.0 or higher. Windows Inter ...

  • Axis Communications P3363-V - page 28

    AXIS P3363–V Network Camera Live View Cong - Pulse activates the output for a dened period of time. The pulse time can be set from 1/100 second to 60 seconds. - Active/Inactive displays two buttons, one or each action. To congure the active and inactive states, go to System Options > Ports & Devices > I/O Ports and set the port ...

  • Axis Communications P3363-V - page 29

    AXIS P3363–V Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area. For more information on view areas, see View Area, on page 21 . Preset Positions A preset position is a predened view that can be used to quickly steer the camera to a specic ...

  • Axis Communications P3363-V - page 30

    AXIS P3363–V Network Camera PTZ (Pan Tilt Zoom) 3. Specify the pause length between runs. 4. Select an available preset position and click Apply . 5. Specify the View Time in seconds or minutes. 6. Specify the View Order or select the Random view order option. 7. Click Save . To modify or remove guard tours, go to PTZ > Guard Tour , select the ...

  • Axis Communications P3363-V - page 31

    AXIS P3363–V Network Camera Detectors Detectors Camera Tampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. To send an alarm, for example an email, an action rule must be set up. To congure tampering: 1. Go to Detectors > Camera Tampering . 2. Set t ...

  • Axis Communications P3363-V - page 32

    AXIS P3363–V Network Camera Detectors Note Using the motion detection feature may decrease the product’s overall performance. Set Up Motion Detection Windows To set up a motion detection Include Window, follow these instructions: 1. Go to Detectors > Motion Detection . 2. Select the Congure Included Windows option and click New . Select t ...

  • Axis Communications P3363-V - page 33

    AXIS P3363–V Network Camera Detectors Low level (0%) Even very small objects trigger motion detection. An object that appears in the window triggers motion detection only for a very short time before it is considered as non-moving. Only very bright objects on a dark background trigger motion detection. Recommended values 5–15% 60–90% 75–95% ...

  • Axis Communications P3363-V - page 34

    AXIS P3363–V Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, down ...

  • Axis Communications P3363-V - page 35

    AXIS P3363–V Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings . 35 ...

  • Axis Communications P3363-V - page 36

    AXIS P3363–V Network Camera Events Events The Axis product can be congured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that denes how and when the action is triggered is called an Action Rule . Available Action Rule triggers and conditions include: • Applica ...

  • Axis Communications P3363-V - page 37

    AXIS P3363–V Network Camera Events - Recurrence — trigger the rule periodically, see Recurrences, on page 39 . This can for example be used to upload an image every 5 minutes. - Use Schedule — trigger the rule according to the selected schedule, see Schedules, on page 38 . Available actions include: • Day/Night Vision Mode — set day mode ...

  • Axis Communications P3363-V - page 38

    AXIS P3363–V Network Camera Events The recording Duration of some actions can be set to include time immediately before and after the event. Select Pre-trigger time and/or Post-trigger time and enter the number of seconds. When While the rule is active is enabled and the action is triggered again during the post-trigger time, the recording time w ...

  • Axis Communications P3363-V - page 39

    AXIS P3363–V Network Camera Events Recurrences Recurrences are used to trigger Action Rules repeatedly, for example every 5 minutes or every hour. To set up a recurrence: 1. Go to Events > Recurrences and click Add . 2. Enter a descriptive name and recurrence pattern. 3. Click OK . To use the recurrence in an Action Rule, rst select Time fr ...

  • Axis Communications P3363-V - page 40

    AXIS P3363–V Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 40 . • To set up action rules, see page 37 . • To access recordings, see Recording List, on page 40 . • To congure camera controlled storage, see ...

  • Axis Communications P3363-V - page 41

    AXIS P3363–V Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may ...

  • Axis Communications P3363-V - page 42

    AXIS P3363–V Network Camera System Options HTTPS HTTPS (HyperText Transfer Protocol over Secure Socket Layer, or HTTP over SSL) is a web protocol providing encrypted browsing. HTTPS can also be used by users and clients to verify that the correct device is being accessed. The security level provided by HTTPS is considered adequate for most commer ...

  • Axis Communications P3363-V - page 43

    AXIS P3363–V Network Camera System Options Certicates CA Certicate The CA certicate is used to validate the identity of the authentication server. Enter the path to the certicate directly, or locate the le using the Browse button. Then click Upload . To remove a certicate, click Remove . Client certicate Client private key Th ...

  • Axis Communications P3363-V - page 44

    AXIS P3363–V Network Camera System Options CA certicates - to authenticate peer certicates, for example the certicate of an authentication server in case the Axis product is connected to an IEEE 802.1X protected network. Note Installed certicates, except preinstalled CA certicates, will be deleted if the product is reset to factory ...

  • Axis Communications P3363-V - page 45

    AXIS P3363–V Network Camera System Options • Set manually allows you to manually set date and time. If using an NTP server, select your Time zone from the drop-down list. If required, check Automatically adjust for daylight saving time changes . The Date & Time Format Used in Images is the date and time format displayed as a text overlay in ...

  • Axis Communications P3363-V - page 46

    AXIS P3363–V Network Camera System Options AVHS is enabled by default. The settings are congured under System Options > Network > TCP IP > Basic . One-click enabled - Press the product’s control button (see Hardware Overview, on page 6 ) to connect to an AVHS service over the Internet. Once registered, Always will be enabled and the ...

  • Axis Communications P3363-V - page 47

    AXIS P3363–V Network Camera System Options Link-Local IPv4 Address Link-Local Address is enabled by default and assigns the Axis product an additional IP address which can be used to access the product from other hosts on the same segment on the local network. The product can have a Link-Local IP and a static or DHCP-supplied IP address at the sa ...

  • Axis Communications P3363-V - page 48

    AXIS P3363–V Network Camera System Options Note This FTP server has nothing to do with the product’s ability to transfer images via FTP to other locations and servers. RTSP The RTSP server running in the Axis product allows a connecting client to start an H.264 stream. The RTSP port number can be changed under System Options > Network > T ...

  • Axis Communications P3363-V - page 49

    AXIS P3363–V Network Camera System Options The following traps are available: • Cold start • Warm start • Link up • Authentication failed SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required. To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 41 . To enable SNMP ...

  • Axis Communications P3363-V - page 50

    AXIS P3363–V Network Camera System Options 3. Click Format and select the desired le system. Note During formatting any previous data stored on the disk will be lost. Mounting is done automatically when the card is inserted or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-ins ...

  • Axis Communications P3363-V - page 51

    AXIS P3363–V Network Camera System Options Port Status The list on the System Options > Ports & Devices > Port Status page shows the status of the product’s input and output ports. Maintenance The Axis product provides several maintenance functions. These are available under System Options > Maintenance . Click Restart to perform a ...

  • Axis Communications P3363-V - page 52

    AXIS P3363–V Network Camera System Options Access Log - Lists all failed attempts to access the product. The Access Log can also be congured to list all connections to the product (see below). Server Report - Provides information about the product status in a pop-up window. The Access Log is automatically included in the Server Report. You can ...

  • Axis Communications P3363-V - page 53

    AXIS P3363–V Network Camera System Options To reset the product to the factory default settings: 1. Disconnect power from the product. 2. Press and hold the control button and reconnect power. See Hardware Overview, on page 6 . 3. Keep the control button pressed for about 15 seconds until the status LED indicator ashes amber. 4. Release the co ...

  • Axis Communications P3363-V - page 54

    AXIS P3363–V Network Camera Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version. The latest version may contain a correction that xes your particular problem. Th ...

  • Axis Communications P3363-V - page 55

    AXIS P3363–V Network Camera Troubleshooting 1. In UNIX/Linux , type the following from the command line: arp -s <IP address> <serial number> temp ping -s 408 <IP address> In Windows , type the following from a command/DOS prompt (this may require that you run the command prompt as an administrator): arp -s <IP address> < ...

  • Axis Communications P3363-V - page 56

    AXIS P3363–V Network Camera Troubleshooting The IP address has been changed by DHCP IP addresses obtained from a DHCP server are dynamic and may change. If the IP address has been changed, use AXIS IP Utility or AXIS Camera Management to located the product on the network. Identify the product using its model or serial number, or by the DNS name ...

  • Axis Communications P3363-V - page 57

    AXIS P3363–V Network Camera Troubleshooting Lower frame rate than expected See Performance Considerations, on page 60 . Reduce the number of applications running on the client computer. Limit the number of simultaneous viewers. Check with the network administrator that there is enough bandwidth available. Check in the AMC Control Panel (H.264 tag ...

  • Axis Communications P3363-V - page 58

    AXIS P3363–V Network Camera Technical Specications Technical Specications Function/group Item Specications Models AXIS P3363–V Image sensor Progressive scan RGB CMOS 1/3” Lens Varifocal, remote focus and zoom, P-iris, IR corrected, mexapixel resolution 6 mm models: 2.5-6 mm, F1.2, horizontal angle of view: 105°-49°,vertical angle o ...

  • Axis Communications P3363-V - page 59

    AXIS P3363–V Network Camera Technical Specications Function/group Item Specications Application Programming Interface Open API for software integration, including the ONVIF specication available at www.onvif.org, as well as VAPIX® and AXIS Camera Application Platform from Axis Communications, specications available at www.axis.com Su ...

  • Axis Communications P3363-V - page 60

    AXIS P3363–V Network Camera Technical Specications Function/group Item Specications Dimensions (HxWxD) 97 x 148 x 148 mm (3.82 x 5.83 x 5.83") Weight 650 g (1.4 lb.) Included accessories Installation guide, CD with installation tools, recording software and user manual, Windows decoder 1-user license Connector kit Video management soft ...

  • Axis Communications P3363-V - page 61

    User Manual Ver. M2.3 AXIS P3363–V Network Camera Date: December 2012 © Axis Communications AB, 2012 Part No. 49864 ...

Produzent Axis Communications Kategorie Security Camera

Dokumente, die wir vom Produzenten des Geräts Axis Communications P3363-V erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Axis Communications
- Bedienungsanleitungen P3363-V
- Produktkarten Axis Communications
- Informationsbroschüren
- oder Energieetiketten Axis Communications P3363-V
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Axis Communications P3363-V.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Axis Communications P3363-V, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Axis Communications P3363-V. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Axis Communications P3363-V ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Axis Communications P3363-V, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Axis Communications P3363-V hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Axis Communications P3363-V verständlich ist.

Eine gänzliche Bedienungsanleitung von Axis Communications sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Axis Communications P3363-V bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Axis Communications P3363-V befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Axis Communications P3363-V, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Axis Communications P3363-V - die uns die ersten Schritte während der Nutzung von Axis Communications P3363-V erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Axis Communications P3363-V hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Axis Communications P3363-V im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Axis Communications P3363-V?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Axis Communications P3363-V nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Axis Communications P3363-V hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)