Bedienungsanleitung Sinclair PG-21

21 Seiten 0.57 mb
Download

Zur Seite of 21

Summary
  • Sinclair PG-21 - page 1

    Model PG-21 Pneumatic Grommet Machine Operating Manual (800) 624-2408 (530) 626-9386 Fax (530) 626-5144 6686 Merchandise Way Diamond Springs, Ca 95619 www.sineqco.com 1 ...

  • Sinclair PG-21 - page 2

    2 INTRODUCTION PNEUMATIC MACHINE MODEL PG-21 FOR PLACING APPLI CATIONS BY HAND The function of this machine is the placemen t of applications or to punch holes (maximum interior diameter of tube grommet 14mm) in materials that need these applications. Specially recommended for placing grommets and washers in: awnings, curtains, advertising signs, e ...

  • Sinclair PG-21 - page 3

    1. DESCRIPTION OF THE MACHINE AND ITS OPERATION. (See figure below) The machine consists of the head, air hoses and pneumatic foot pedal. The moving parts in the machine are located inside the head (pneumatic cylinder, manometer, axles, dies, etc.). After placing the machine in its permanent location, without fitting the air hosepipe into the mouth ...

  • Sinclair PG-21 - page 4

    4 Technical Data: HEAD MEASUREMENTS: DEPTH: 30 cm WIDTH: 11’5 cm HEIGHT: 38 cm WEIGHT (with pneumatic pedal): 14 Kg Installation: The operator can work in a seated or a standing position, depending on the height of the machine. The minimum space recommended must be sufficient to k eep the safety space in all directions for the operator to work pr ...

  • Sinclair PG-21 - page 5

    BEFORE STARTING THE MACHINE, READ THESE WARNINGS CAREFULLY. The following are a series of instructions and warnings which must be taken into account with regard to t he model PG-21. - Before connecting the machine to the compressor, it should be placed in its permanent location. Do not connect any electrical devices to the machine before it has bee ...

  • Sinclair PG-21 - page 6

    Machine Description Maximum interior diameter of grommet and washer is 12mm. The machine perforates and sets the grom m et with the washer at the same tim e. Each set of dies sets only one grommet and washer model; the grommet models m ay differ in: the head size “B”, the length “C ”, the interior diam eter of t ube “A”, the thickness, ...

  • Sinclair PG-21 - page 7

    7 SETTING UP THE MACHINE FO R ITS OPERATION Before starting the machine for the first time, and each time the location of the machine is changed, or any changes are made in parts or any adjustments are done to it, we recommend the following steps: After placing and making the m achine leve l in its permanent location “ST ILL WITHOUT PLUGGING IT I ...

  • Sinclair PG-21 - page 8

    8 For the following procedures, refer to the diagram on page 11 CHANGE OF DIES FOR THE SAME GROMMET AND / OR WASHER SIZE Changing the bottom die #19 : With the machine disconnected from the compre ssor (and from the power source if it has any electrical devices). - Shut the air inlet part #260, - Turn the ring guard # 306 by looseni ng the allew sc ...

  • Sinclair PG-21 - page 9

    9 For adjusting the cutting pressure (the cutti ng pressure punches a hole in the material), you have to turn the bottom die # 219 to the right or to the left, so that when you start the machine and press the foot pedal, the top set spi ndle # 218 barely touc hes the bottom die # 219. With the machine disconnected from the compre ssor (and from the ...

  • Sinclair PG-21 - page 10

    10 RING GUARD ADJUSTMENTS Whenever the machine is adjusted or modified or some parts are changed it is n ecessary to adjust the safety device again (pneumatic safety cylinder # 26 5, end of race # 267, ring guard # 306, etc) so that it may work properly. - Connect the machine to the comp ressor and open the air inlet # 260, - The safety manometer # ...

  • Sinclair PG-21 - page 11

    238 217 306 219 194 230 260 Recommended pressure is 87-90 psi. Input re gulator mu st be used with the PG-21. 11 ...

  • Sinclair PG-21 - page 12

    12 MAINTENANCE MECHANICAL PART OF THE MACHINE For an optimal operation of the machine, it is recommended that you keep some parts clean and always lubricated. The cleaning shoul d ALWAYS be done with the machine disconnected from the electrical power source and the compressor. The pedal we press to operate the m achine, shou ld always be clean a nd ...

  • Sinclair PG-21 - page 13

    13 TROUBLESHOOTING PROBLEM CAUSE SOLUTION THE MACHINE DOES NOT OPERATE WHEN PRESSING THE FOOT PEDAL. Make sure the air inlet is conn ected to the compressor. Make sure the air inlet is in the open position. Make sure the correct air pres sure is supplied Connect It Open T he Hand le Make sure the com pressor is supplying the correct air pressure . ...

  • Sinclair PG-21 - page 14

    Schematic # Part# Description 62 PGR21062 Grease cups (Set of 2) 63 PGR21063 Long lubrication tube 64 PGR21064 Short lubrication tube 125 PGR21125 Left cylinder guard 126 PGR21126 Right cylinder guard 135 PGR21135 Hold guard 161 PGR21161 Head 162 PGR21162 Top Cover 194 PGR21194 Threaded pin for bottom die cover 204 PGR21204 Pneumatic foot pedal 205 ...

  • Sinclair PG-21 - page 15

    Schematic # Part# Description 111 PGR21111 Lever pin 112 PGR21112 Guide wheel pin 113 PGR21113 Driving stem guide wheel 114 PGR21114 Pin for die spindle 115 PGR21115 Connecting rod 116 PGR21116 Pin for connecting rod 117 PGR21117 Bolt for yoke 118 PGR21118 Nut for yoke 119 PGR21119 Yoke 120 PGR21120 Lever 15 ...

  • Sinclair PG-21 - page 16

    121 PGR21121 Driving Stem 122 PGR21122 Top set spindle 281 PGR21281 Ring for 12 connecting rod pin Schematic # Part# Description 21 PGR21021 M5 elbow tube 123 PGR21123 Screw for part #304 128 PGR21128 Screw for holding part #267 265 PGR21265 Pneumatic safety cylinder 267 PGR21267 End of race 275 PGR21275 Part for holding ring guard 276 PGR21276 Nut ...

  • Sinclair PG-21 - page 17

    Schematic # Part# Description 2 PGR21002 Hinge for cylinder #271 4 PGR21004 Support for valve 7 PGR21007 Safety control 0-2 kg 8 PGR21008 Safety manometer 10 PGR21010 Silencer 1/8 11 PGR21011 Reduction 12 PGR21012 Buttress 1/8 15 PGR21015 Elbow 1/8 16 PGR21016 Elbow ¼ (2) 17 PGR21017 Elbow ¼ tube 8 18 PGR21018 Elbow ¼ tube 4 19 PGR21019 Elbow 1/ ...

  • Sinclair PG-21 - page 18

    Schematic # Part# Description 21 PGR21021 J set of dies (Specify size) 217 PGR21217 Top die grommet & washer * 218 PGR21218 Top set spindle grommet & washer * 219 PGR21219 Bottom die grommet & washer * 229 PGR21229 Spring for top set spindle * 230 PGR21230 Bottom die holder * 238 PGR21238 Nut for adjusting the top die #217 * 241 PGR2124 ...

  • Sinclair PG-21 - page 19

    Tools And Parts Tools: Along with your machine, you will find all th e necessary tools for adjustments and maintenance. Parts Although the PG-21 doesn’t come with any parts, Sinclair Equipment recomm ends having an extra bottom die, or set of dies for spares. 19 ...

  • Sinclair PG-21 - page 20

    20 ...

  • Sinclair PG-21 - page 21

    21 NOTES ...

Produzent Sinclair Kategorie Drill

Dokumente, die wir vom Produzenten des Geräts Sinclair PG-21 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Sinclair
- Bedienungsanleitungen PG-21
- Produktkarten Sinclair
- Informationsbroschüren
- oder Energieetiketten Sinclair PG-21
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Sinclair PG-21.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Sinclair PG-21, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Sinclair PG-21. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Sinclair PG-21 ansehen.

Die komplette Bedienungsanleitung des Geräts Sinclair PG-21, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Sinclair PG-21 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Sinclair PG-21 verständlich ist.

Eine gänzliche Bedienungsanleitung von Sinclair sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Sinclair PG-21 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Sinclair PG-21 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Sinclair PG-21, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Sinclair PG-21 - die uns die ersten Schritte während der Nutzung von Sinclair PG-21 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Sinclair PG-21 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Sinclair PG-21 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Sinclair PG-21?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Sinclair PG-21 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Sinclair PG-21 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)