Bedienungsanleitung Cisco Systems 7200 VXR

64 Seiten 1.51 mb
Download

Zur Seite of 64

Summary
  • Cisco Systems 7200 VXR - page 1

    CHAPTER 1-1 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 1 Cisco 7200 VXR Product Overview This chapter provides physical and functional o vervie ws of the Cisco 7200 VXR routers. Descriptions and examples of software commands are included when the y are necessary for replacing, installing, conf iguring, or maintaining the router ...

  • Cisco Systems 7200 VXR - page 2

    1-2 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Physical Description The Cisco 7200 VXR routers support the high-speed network processing engine, NPE-G2, and all other av ailable network processing engines. The NPE-G2 provides high-speed performance with the Motorola Freescale 7448 1.67-G ...

  • Cisco Systems 7200 VXR - page 3

    1-3 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Physical Description See T able 1-1 for the Cisco 7200 VXR physical specif ications and po wer requirements: T able 1 -1 Ph ysical Specifications Description Specif ication Midplane T w o primary PCI buses, and one secondary PCI bus • W i ...

  • Cisco Systems 7200 VXR - page 4

    1-4 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Software Requirements Note For a chassis footprint, additional dimensions, and clearance requirements for the Cisco 7200 VXR routers, see the “Site Requirement Guidelines” section on page 2-3 in Chapter 2, “Preparing for Installation. ...

  • Cisco Systems 7200 VXR - page 5

    1-5 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Cisco 7204VXR Overview W ith the NPE-G1 or NPE-G2 installed and the Port Adapter Jacket Card installed in the I/O controller slot, an additional port adapter slot is av ailable. Note If you hav e diff iculty installing a processing engine or ...

  • Cisco Systems 7200 VXR - page 6

    1-6 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Cisco 7204VXR Overview Figur e 1 -2 Cisco 7204VXR Router—Rear V iew The NPE-G2 and NPE-G1 hav e external connectors and status LEDs for the three Gigabit Ethernet interfaces as well as console and auxiliary ports. The network processing en ...

  • Cisco Systems 7200 VXR - page 7

    1-7 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Cisco 7206VXR Overview Three internal fans dra w cooling air into the chassis and across internal components to maintain an acceptable operating temperature. (See Figure 1-2 .) The three fans are enclosed in a tray that is located inside the ...

  • Cisco Systems 7200 VXR - page 8

    1-8 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Cisco 7206VXR Overview W ith the NPE-G1 or NPE-G2 installed and the Port Adapter Jacket Card installed in the I/O controller slot, an additional port adapter slot is av ailable. Note If you hav e diff iculty installing a processing engine or ...

  • Cisco Systems 7200 VXR - page 9

    1-9 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Cisco 7206VXR Overview Figur e 1 -4 Cisco 7206VXR Router—Rear V iew The rear of the Cisco 7206VXR router provides access to the network processing engine or network services engine and up to two po wer supplies. (See Figure 1-4 .) The NPE- ...

  • Cisco Systems 7200 VXR - page 10

    1-10 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Adjacent to the power supply bays are tw o chassis grounding receptacles that provide a chassis ground connection for ESD equipment or a two-hole grounding lug. (See Figure 1-4 .) Three internal fans draw cooling air ...

  • Cisco Systems 7200 VXR - page 11

    1-11 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units • CompactFlash Disks, Flash Disks, and PC Cards, page 1-52 • Rack-Mount and Cable-Management Kit, page 1-53 Note Replacement instructions for removing and replacing FR Us are contained in separate online document ...

  • Cisco Systems 7200 VXR - page 12

    1-12 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units – The NPE-200 has an R5000 microprocessor that operates at an internal clock speed of 200 MHz. – The NPE-175 has an RM5270 microprocessor that operates at an internal clock speed of 200 MHz. – The NPE-100 and N ...

  • Cisco Systems 7200 VXR - page 13

    1-13 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units – The NPE-100, NPE-150, and NPE-200 use DRAM for storing routing tables, network accounting applications, packets of information in preparation for process switching, and packet b uffering for SRAM ov erf low (exce ...

  • Cisco Systems 7200 VXR - page 14

    1-14 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units • Booting and reloading images • Managing port adapters (recognition and initialization during online insertion and remov al) The following f igures and memory tables provide information about your NPE or NSE: ? ...

  • Cisco Systems 7200 VXR - page 15

    1-15 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -5 NPE-G2 T able 1-2 lists the NPE-G2 memory specif ication, and T able 1-3 lists the factory-installed SDRAM conf igurations and their product numbers. 1 Midplane connectors 6 Flash memory (U13) 2 Boot R O ...

  • Cisco Systems 7200 VXR - page 16

    1-16 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -6 NPE-G1 T able 1-4 lists the NPE-G1 memory specif ication, and T able 1-5 lists the factory-installed SDRAM conf igurations and their product numbers. Primary cache 32 KB (16 KB instruction, 16 KB data) ? ...

  • Cisco Systems 7200 VXR - page 17

    1-17 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units T able 1 -4 NPE-G1 Memory Specifications Memory T ype Size Quantity Description Component Location on the NPE-G1 Board SDRAM 128 MB, 256 MB, 512 MB 2 128-MB, 256-MB, or 512-MB SODIMMs J3, J4 Boot R OM 512 KB 1 Repro ...

  • Cisco Systems 7200 VXR - page 18

    1-18 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -7 NSE-1 T able 1-6 lists the NSE-1 memory specif ications, and T able 1-7 lists the NSE-1 factory-installed SDRAM conf igurations and their product numbers. 1 Network controller board 8 Midplane connectors ...

  • Cisco Systems 7200 VXR - page 19

    1-19 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -8 NPE-400 Secondary cache 256 KB — RM7000 processor , internal, unif ied instruction and data cache U22 T ertiary cache 2 MB (f ixed) — RM7000 processor , external cache U7, U9, U12, U14, U17 1. Locati ...

  • Cisco Systems 7200 VXR - page 20

    1-20 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units T able 1-8 lists the NPE-400 memory specif ications, and T able 1-9 lists factory-installed SDRAM conf igurations and their product numbers. T able 1 -8 NPE-400 Memory Specifications Memory T ype Size Quantity Descr ...

  • Cisco Systems 7200 VXR - page 21

    1-21 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -9 NPE-300 T able 1-10 lists the NPE-300 memory specif ications, and T able 1-11 lists factory-installed SDRAM conf igurations and their product numbers. 1 Midplane connectors 9 RM7000 microprocessor 2 Ke y ...

  • Cisco Systems 7200 VXR - page 22

    1-22 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Note The NPE-300 contains two banks of SDRAM. Both SDRAM banks are used for all packet memory requirements; ho wev er, bank 0 is used e xclusively for pack et memory and is set at a f ixed conf iguration in the facto ...

  • Cisco Systems 7200 VXR - page 23

    1-23 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -1 0 NPE-225 T able 1-12 lists the NPE-225 memory specif ications, and T able 1-13 lists factory-installed SDRAM conf igurations and their product numbers. 1 Network controller board 6 Handle 2 System contr ...

  • Cisco Systems 7200 VXR - page 24

    1-24 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units T able 1 -12 NPE-225 Memory Specifications Memory T ype Size Quantity Description Location 1 1. Location on processing engine board. See Figure 1-10 . SDRAM 64, 128, 256 MB 1 SDRAM slot 64-MB, 128- MB, or 256-MB SDR ...

  • Cisco Systems 7200 VXR - page 25

    1-25 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -1 1 NPE-200 T able 1-14 lists the NPE-200 memory specif ications, and T able 1-15 lists factory-installed DRAM conf igurations and their product numbers. 1 System controller 7 Midplane connectors 2 R5000 m ...

  • Cisco Systems 7200 VXR - page 26

    1-26 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Note T o prev ent DRAM errors in the NPE-100, NPE-150, or NPE-200, and to ensure that your system initializes correctly at startup, DRAM bank 0 (socket U18 and U25, or U11 and U25) must contain no fewer than tw o SIM ...

  • Cisco Systems 7200 VXR - page 27

    1-27 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -12 NPE-1 75 T able 1-16 lists the NPE-175 memory specif ications, and T able 1-17 lists memory conf igurations. 1 Network controller board 6 Handle 2 System controller 7 Midplane connectors 3 Processor eng ...

  • Cisco Systems 7200 VXR - page 28

    1-28 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units T able 1 -16 NPE-1 75 Memory Specifications Memory T ype Size Quantity Description Location 1 1. Location on processing engine board. See Figure 1-12 . SDRAM 64 or 128 MB 1 SDRAM slot DIMM U15 Boot R OM 512 KB — O ...

  • Cisco Systems 7200 VXR - page 29

    1-29 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -13 NPE-150 T able 1-18 lists the NPE-150 memory specif ications, and T able 1-19 lists memory conf igurations. 1 System controller 7 Midplane connectors 2 R4700 microprocessor 8 T emperature sensor 3 1-MB ...

  • Cisco Systems 7200 VXR - page 30

    1-30 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Note T o prev ent DRAM errors in the NPE-100, NPE-150, or NPE-200, and to ensure that your system initializes correctly at startup, DRAM bank 0 (socket U18 and U25, or U11 and U25) must contain no fewer than tw o SIM ...

  • Cisco Systems 7200 VXR - page 31

    1-31 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Note T o prev ent DRAM errors in the NPE-100, NPE-150, or NPE-200, and to ensure that your system initializes correctly at startup, DRAM bank 0 (socket U18 and U25, or U11 and U25) must contain no fewer than tw o SIM ...

  • Cisco Systems 7200 VXR - page 32

    1-32 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Input/Output Controller This section describes f i ve dif ferent models of I/O controllers. These models are distinguished from one another by their Ethernet interface options. T able 1-22 lists the I/O controllers b ...

  • Cisco Systems 7200 VXR - page 33

    1-33 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -15 C7200-I/O-GE+E—With GBIC Gigabit Ether net and RJ-45 Ethernet Receptacles Figur e 1 -16 C7200-I/O-2FE/E—With T wo RJ-45 Ether net/Fast Ether net Receptacles 1 T emperature sensor 8 Capti ve installa ...

  • Cisco Systems 7200 VXR - page 34

    1-34 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units 1 T emperature sensor 7 SRAM (U19) 2 Midplane connectors 8 Capti ve installation scre w 3 Battery for SRAM 9 PC Card slots 4 8-MB Flash memory (soldered) (U15) 10 RJ-45 Fast Ethernet ports 5 8-MB Flash memory (solder ...

  • Cisco Systems 7200 VXR - page 35

    1-35 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -17 C7200-I/O-FE—With MII and RJ-45 Fast Ether net Receptacles (V ersion 1) 1 T emperature sensor 8 PC Card slots 2 Midplane connectors 9 Optional Fast Ethernet interface (MII port and RJ-45 port) 3 Flash ...

  • Cisco Systems 7200 VXR - page 36

    1-36 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -18 C7200-I/O-FE—With MII and RJ-45 Fast Ether net Receptacles (V ersion 2) Note Y our I/O controller with the MII and RJ-45 Fast Ethernet receptacles (C7200-I/O-FE) might look like the f irst illustratio ...

  • Cisco Systems 7200 VXR - page 37

    1-37 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Note In n Figure 1-20 , the NVRAM is replaced by an SRAM component (U14) that is made to act like the NVRAM by the addition of some external components, one of which is the b utton-type lithium battery labeled “Bat ...

  • Cisco Systems 7200 VXR - page 38

    1-38 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -20 C7200-I/O—Without Fast Ether net Por t (V ersion 2) 1 T emperature sensor 8 Battery for SRAM 2 FPGA conf iguration PR OM (U9) 9 Capti ve installation scre w 3 Midplane connectors 10 PC Card slots 4 4- ...

  • Cisco Systems 7200 VXR - page 39

    1-39 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -21 C7200-I/O-FE-MII—With Single MII Fast Ether net Receptacle Note C7200-I/O-FE-MII, although still supported by Cisco Systems, was discontinued as an orderable product in May 1998. T able 1-23 lists the ...

  • Cisco Systems 7200 VXR - page 40

    1-40 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units LED Descriptions All I/O controllers hav e LEDs, and the NPE-G1 and NPE-G2 also have interfaces that ha ve LEDs. The I/O controller faceplate contains LEDs that indicate system and port status; two additional LEDs in ...

  • Cisco Systems 7200 VXR - page 41

    1-41 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units or not an I/O controller is in the system with the NPE-G1 or NPE-G2. The SLO T ACTIVE LED is on if there is a CompactFlash Disk in the NPE-G1. The CF A CTV LED is on if there is a CompactFlash Disk in the NPE-G2. Cau ...

  • Cisco Systems 7200 VXR - page 42

    1-42 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units NPE-G1 LEDs USB USB ports Flashing green Acti vity Off No activity CF A CTV CompactFlash Disk Flashing green Acti vity Off No activity SYST ST A T System status Solid green Cisco IOS has successfully booted. Flashing ...

  • Cisco Systems 7200 VXR - page 43

    1-43 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Input/Output Controller C7200-I/O LEDs Figure 1-22 sho ws the LEDs on the I/O controller model with no Ethernet ports (C7200-I/O). This I/O controller has no port-specif ic LEDs. T able 1-24 describes the LEDs on thi ...

  • Cisco Systems 7200 VXR - page 44

    1-44 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -23 C720 0-I/O-GE+E LEDs and CPU Reset Butt on Input/Output Controller C7200-I/O-2FE/E LEDs Figure 1-24 sho ws the LEDs on the I/O controller with the two autosensing 10/100-Mbps RJ-45 receptacles (C7200-I/ ...

  • Cisco Systems 7200 VXR - page 45

    1-45 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Input/Output Controller C7200-I/O-FE LEDs Figure 1-25 sho ws the LEDs on the I/O controller with the Fast Ethernet port that is equipped with an MII receptacle and an RJ-45 receptacle (C7200-I/O-FE), and T able 1-29 ...

  • Cisco Systems 7200 VXR - page 46

    1-46 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -25 C720 0-I/O-FE LEDs and CPU Reset Butt on T able 1 -29 C7200-I/O-FE I/O Controller LEDs LED Color Function MII EN Green Indicates that the Fast Ethernet MII receptacle is initialized and enabled by the s ...

  • Cisco Systems 7200 VXR - page 47

    1-47 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Note An MII LINK LED is not provided on this I/O controller because the LED is pro vided on external transceiv ers that are required for connecting to the MII receptacle on the I/O controller . See Chapter 3, “Inst ...

  • Cisco Systems 7200 VXR - page 48

    1-48 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Note The port adapters installed in the Cisco 7200 VXR routers support OIR. For an explanation of OIR, see the “Online Insertion and Remov al” section on page 1-57 . All port adapters and service adapters connect ...

  • Cisco Systems 7200 VXR - page 49

    1-49 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Power Supplies The Cisco 7200 VXR routers come equipped with one 280W A C-input power supply . (A 280W DC-input power supply is a vailable as an option.) Y ou must order the second power supply separately . A second ...

  • Cisco Systems 7200 VXR - page 50

    1-50 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -28 Cisco 720 0 Ser ies AC-Input P ow er Supply The A C-input power supply has a receptacle for an A C-input power cable. A modular po wer cable connects the A C-input power supply to the site A C power sou ...

  • Cisco Systems 7200 VXR - page 51

    1-51 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units The DC-input power supply has DC-input power leads that are hardwired to a DC-input terminal block. A cable tie is shipped with each DC-input power supply to secure the leads to the po wer supply faceplate and provid ...

  • Cisco Systems 7200 VXR - page 52

    1-52 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units Figur e 1 -30 Cisco 720 0 VXR Chassis—7206VXR Shown CompactFlash Disks, Flash Disks, and PC Cards The Cisco 7206VXR supports up to two installed Flash Disks or two PC Cards, also called Flash memory cards. The NPE- ...

  • Cisco Systems 7200 VXR - page 53

    1-53 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Field-Replaceable Units See T able 1-31 , T able 1-32 , and T able 1-33 for the factory-installed Flash memory card options and their product numbers, the Flash Disk memory options and their product numbers, and the CompactFlash Disk memory ...

  • Cisco Systems 7200 VXR - page 54

    1-54 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Functional Overview This section provides a functional o vervie w of the Cisco 7200 VXR routers. It describes the numbering and addressing scheme of the port adapters for the router , the environmental monitoring and rep ...

  • Cisco Systems 7200 VXR - page 55

    1-55 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Figur e 1 -32 Por t Adapter Slot Number ing—Cisco 7206VXR The Media Access Control (MA C) address or hardware address is a standardized data link layer address that is required for certain network interface types. Thes ...

  • Cisco Systems 7200 VXR - page 56

    1-56 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Router# show interfaces FastEthernet0/0 is administratively down, line protocol is down Hardware is i82543 (Livengood), address is 0000.0000.0000 (bia 0000.0000.0000) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliabi ...

  • Cisco Systems 7200 VXR - page 57

    1-57 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview The following e xample shows the display for the f irst port on the Fast Ethernet port adapter in port adapter slot 3: Router# show interface fastethernet 5/0 FastEthernet5/0 is up, line protocol is up Hardware is DEC211 ...

  • Cisco Systems 7200 VXR - page 58

    1-58 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Note The Port Adapter Jacket Card does not support OIR. Ho wever , the port adapter installed in the Port Adapter Jacket Card does support OIR. Note As you disengage the port adapter from the router or switch, online ins ...

  • Cisco Systems 7200 VXR - page 59

    1-59 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Environmental Monitoring and Reporting Functions En vironmental monitoring and reporting functions are controlled by the network processing engine or network services engine and allo w you to maintain normal system opera ...

  • Cisco Systems 7200 VXR - page 60

    1-60 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview T able 1 -34 NPE-G2Processor -Monitored T emper atur e Thresholds NPE-G2 1 1. With an I/O controller installed. Low Warning High Warning Shutdown NPE inlet 111 F (44 C) 138 F (59 C) 176 o F (80 o C) NPE outlet 120 F (49 ...

  • Cisco Systems 7200 VXR - page 61

    1-61 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Note A low w arning or high warning message does not mean that the r outer is at risk of malfunctioning or being damaged. The lo w warning and high warning ranges in T able 1-34 and T able 1-35 are informational. If a lo ...

  • Cisco Systems 7200 VXR - page 62

    1-62 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Below are sample high critical messages from chassis with 3V and 5V po wer supplies in Cisco IOS Release 12.0(23): Router(boot)# 00:02:47:%ENVM-2-ENVCRIT:+3.45 V measured at +3.72 Router(boot)# 00:06:51:%ENVM-2-ENVCRIT:+ ...

  • Cisco Systems 7200 VXR - page 63

    1-63 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Follo wing is sample output of the show en vironment last command: NPE300(boot)# show environment last chassis inlet previously measured at 26C/78F chassis outlet 1 previously measured at 28C/82F chassis outlet 2 previou ...

  • Cisco Systems 7200 VXR - page 64

    1-64 Cisco 7200 VXR Installation and Configuration Guide OL-5013-08 Chapter 1 Cisco 7200 VXR Product Overview Functional Overview Follo wing is sample output of the show en vironment all command: NPE300(boot)# show environment all Power Supplies: Power Supply 1 is empty. Power Supply 2 is Zytek AC Power Supply. Unit is on. Temperature readings: cha ...

Produzent Cisco Systems Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts Cisco Systems 7200 VXR erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco Systems
- Bedienungsanleitungen 7200 VXR
- Produktkarten Cisco Systems
- Informationsbroschüren
- oder Energieetiketten Cisco Systems 7200 VXR
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Systems 7200 VXR.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Systems 7200 VXR, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Systems 7200 VXR. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Systems 7200 VXR ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Systems 7200 VXR, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Systems 7200 VXR hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Systems 7200 VXR verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Systems 7200 VXR bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Systems 7200 VXR befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Systems 7200 VXR, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Systems 7200 VXR - die uns die ersten Schritte während der Nutzung von Cisco Systems 7200 VXR erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Systems 7200 VXR hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Systems 7200 VXR im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Systems 7200 VXR?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Systems 7200 VXR nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Systems 7200 VXR hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)