Deutsch dropdown-ico

Bedienungsanleitung Kathrein UFS 932sw

32 Seiten Betrifft nicht
Download

Zur Seite of 32

Summary
  • Kathrein UFS 932sw - page 1

    If you do not know the con fi guration of your satellite reception system, contact your specialist dealer for the fi rst installation of your receiver. Operating instructions part 1 UFS 932 Connection and Setup English Safety Instructions – Important Notes ......................................................................................... ...

  • Kathrein UFS 932sw - page 2

    2 Mains cable Make sure that the mains cable (power supply cable) is not damaged. Units with a damaged mains cable must be disconnected from the mains (unplugged at the mains power socket) and repaired by an electrical specialist before being used. Only use the power supply unit supplied (if available). Risk of fatal injury due to electric shock! D ...

  • Kathrein UFS 932sw - page 3

    3 Periods of extended absence, thunderstorms, mains socket accessibility In order to disconnect the unit from the mains completely , the mains plug must be unplugged from the wall socket! Therefore install the unit close to a mains socket and make sure this socket is accessible at all times, so that you can disconnect the unit from the mains if nec ...

  • Kathrein UFS 932sw - page 4

    4 Product return/original packaging Make sure that the ventilation slots on the unit are not blocked or covered in any way . Otherwise the unit may overheat. There is a risk of fi re! You must not disconnect the receiver from the mains while it is in operation! This can lead to a loss of data and corruption of the software. Safety Instructions – ...

  • Kathrein UFS 932sw - page 5

    5 Scope of supply ■ UFS 932 ■ HD+ smartcard ■ Remote control RC 674 ■ HDMI cable ■ 2 batteries AAA 1.5 V ■ Operating instructions (part 1 and part 2) ■ Safety instructions (multi-lingual) ■ HD+ fl yer The accessories supplied may differ in appearance from those illustrated! Remote Control HDMI cable Batteries Smartcard ...

  • Kathrein UFS 932sw - page 6

    6 Front/rear view of the receiver (front fl ap open) Connection and setup 1 3 2 8 10 14 15 16 17 4 5 6 7 9 11 12 13 18 19 ...

  • Kathrein UFS 932sw - page 7

    7 Connection and setup *) CA modules and smartcards are not included with this product ** ) The unit is not fully disconnected from the mains (see the sections “Safety Instructions - Important Instructions” and “Periods of extended absence, thunderstorms, mains socket accessibility”) Front: 1. On/Off (operation/stand-by) 2. 4-character nume ...

  • Kathrein UFS 932sw - page 8

    8 Connection and setup Inserting batteries into the remote control Remove the cover on the rear of the remote control. Insert the two batteries supplied into the remote control. Ensure correct polarity of the batteries; the + and – markings as indicated inside the battery compartment. Slide the cover back onto the housing until it locks in place. ...

  • Kathrein UFS 932sw - page 9

    9 If you do not know the con fi guration of your satellite reception system, contact your specialist dealer. Connect the Sat IF inputs on the receiver to the satellite reception system. Use coaxial cable with an F standard connector (see illustration on right). HDMI Scart TV Conventional DiSEqC™ system Connect the satellite receiver (HDMI or alt ...

  • Kathrein UFS 932sw - page 10

    10 There are two ways you can access the digital audio. HDMI The stereo audio is transmitted to your TV set via the HDMI interface. If your TV set also supports Dolby Digital, you can also receive the Dolby Digital audio via the HDMI interface (providing it is broadcast by the channel provider). On this issue refer to the operating manual for your ...

  • Kathrein UFS 932sw - page 11

    11 Before you start to use the UFS 932, read the sections “Safety Instructions - Important Instructions”, “Important Information” and “Connection and Set-Up” through to the item “First Installation”. Do not connect the unit to the mains until all installation work has been properly carried out. The guidance provided in the “First ...

  • Kathrein UFS 932sw - page 12

    12 The following languages are available: German, English, French, Italian, Spanish, Czech, Dutch, Polish T urkish and Russian. Press the  (green) button to move to the next menu. Resolution (HDMI/YUV format) Here you can select the video resolution that will be output at the TV set. Either - 1080p (resolution 1920 x 1080, full-screen images) - ...

  • Kathrein UFS 932sw - page 13

    13 Video Output Here you can select whether the receiver will output the RGB signal at the Scart sockets - selection “RGB” (Red/Green/Blue signal). If the setting “RGB” is selected, no TV signal can be output at the YPbPr sockets. Connection and setup TV Aspect Ratio Here you can select the TV picture format. Either - 4:3, - 16:9 or - Auto ...

  • Kathrein UFS 932sw - page 14

    14 Connection and setup Y ou should perform the antenna con fi guration / make changes yourself only if you are fully familiar with the particulars of your reception system. The settings for the tuner con fi guration should be perfo rmed by a specialist engineer for this reception system. The following on-screen display appears: If your receiver ...

  • Kathrein UFS 932sw - page 15

    15 Connection and setup LNB only Select Satellite Use the  buttons here to select the satellite whose signal is present at the tuner . LNB T ype If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universa ...

  • Kathrein UFS 932sw - page 16

    16 LNB Power This is factory-set to “On”, but must be changed if your LNB has its own power supply . In most cases the LNB power supply is provided by the receiver . (T est) transponder (TP) Select the selection fi eld “TP”. Here you can select a transponder for checking whether your settings are correct using the signal strength bar and s ...

  • Kathrein UFS 932sw - page 17

    17 Connection and setup DiSEqC™1.0 Select satellite and port (satellite slot) Here you can select the satellites whose signals you wish to receive. Select only those satellites that are present in the signal at the tuner . Y ou can set up a maximum of four satellites. First use the  buttons in the “Satellite” line to select the desired ...

  • Kathrein UFS 932sw - page 18

    18 Connection and setup Single Cable System Select satellite and port (satellite slot) Here you can select the satellites whose signals you wish to receive. Select only those satellites that are present in the signal at the tuner . Y ou can set up a maximum of two satellites. First use the  buttons in the “Satellite” line to select the de ...

  • Kathrein UFS 932sw - page 19

    19 Connection and setup (T est) transponder (TP) Select the selection fi eld “TP”. Here you can select a transponder for checking whether your settings are correct using the signal strength bar and signal quality bar . When you have completed all settings, press the  (green) button. Y ou will automatically be shown the display for “Update ...

  • Kathrein UFS 932sw - page 20

    20 Connection and setup Always follow the operating instructions from your Pay-TV provider and the instructions supplied with the Smartcard and the CA (Conditional Access) module! Smart cards and CA modules are not included with this product! The cards and modules are issued by the respective pay TV providers, and contain the subscriber data and de ...

  • Kathrein UFS 932sw - page 21

    21 Inserting the CA module into the CI The Common Interface (CI+)  of the UFS 932 is suitable for insertion of a CI+ module (or CA module) and is located on the front panel of the receiver (behind the fl ap). The CA module  accepts the smart card  (chip contacts pointing downwards and towards socket strip) and is then inserted in the CI+ ...

  • Kathrein UFS 932sw - page 22

    22 T roubleshooting In the event of a malfunction, fi rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to wall socket 2. Antenna cables are connected to the receiver input 3. Receiver and TV set correctly connected by a HDMI or Scart cable 4. Audio connections are made to the Hi-Fi or Dolby ...

  • Kathrein UFS 932sw - page 23

    23 Service If, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. The Kathrein customer hotline is also at your disposal. Tel: 0900/1122240 * * (0.49 EUR per minute on Deutsche Telekom AG land lines, calls ...

  • Kathrein UFS 932sw - page 24

    24 T echnical appendix Advanced connection example Scart Cinch (YPbPr) External hard disk Dolby Digital system Hi- fi system ...

  • Kathrein UFS 932sw - page 25

    25 T echnical appendix T echnical Speci fi cations T ype UFS 932si/HD+ UFS 932sw/HD+ Order no./colour 20210188/silver 20210189/black RF section Sat IF band MHz 950-2150 Input level band dB μ V 44-83 TV system, video Modulation, FEC, demultiplexer DVB-S-/DVB-S2 standard Video resolution CCIR 601 (720 x 576 lines), 576i, 576p, 720p, 1080i, 1080p Vi ...

  • Kathrein UFS 932sw - page 26

    26 T echnical appendix Sat IF connection examples 2 x UAS 571 Sat-ZF 950-2150 MHz **) ESD../ESC.. EXR 21 Signal 1 Signal 2 Position OPTION UC1 ** ) Overvoltage protection KAZ 1 1/KAZ 12 Individual reception systems Community antenna network systems (4 x Sat IF) Sat IF Sat IF Sat IF ...

  • Kathrein UFS 932sw - page 27

    27 T echnical appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 Community antenna network systems (8 x Sat IF), multi-feed Community antenna network systems (16 x Sat IF), multi-feed Sat IF Sat IF Sat IF Sat IF Sat IF ...

  • Kathrein UFS 932sw - page 28

    28 T echnical appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 Single cable systems Sat IF ...

  • Kathrein UFS 932sw - page 29

    29 T echnical appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 Sat IF Sat IF ...

  • Kathrein UFS 932sw - page 30

    30 For your notes ...

  • Kathrein UFS 932sw - page 31

    31 For your notes ...

  • Kathrein UFS 932sw - page 32

    Internet: www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Str. 1 - 3 • P .O. Box 100 444 • 83004 Rosenheim • GERMANY • phone +49 8031 184-0 • Fax +49 8031 184-385 936.4068/-/ZWT/031 1/d - Subject to changes! ...

Produzent Kathrein Kategorie Receiver

Dokumente, die wir vom Produzenten des Geräts Kathrein UFS 932sw erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Kathrein
- Bedienungsanleitungen UFS 932sw
- Produktkarten Kathrein
- Informationsbroschüren
- oder Energieetiketten Kathrein UFS 932sw
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Kathrein UFS 932sw.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Kathrein UFS 932sw, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Kathrein UFS 932sw. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Kathrein UFS 932sw ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Kathrein UFS 932sw, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Kathrein UFS 932sw hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Kathrein UFS 932sw verständlich ist.

Eine gänzliche Bedienungsanleitung von Kathrein sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Kathrein UFS 932sw bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Kathrein UFS 932sw befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Kathrein UFS 932sw, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Kathrein UFS 932sw - die uns die ersten Schritte während der Nutzung von Kathrein UFS 932sw erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Kathrein UFS 932sw hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Kathrein UFS 932sw im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Kathrein UFS 932sw?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Kathrein UFS 932sw nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Kathrein UFS 932sw hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)