Deutsch dropdown-ico

Bedienungsanleitung Bretford LAP30EULBA

33 Seiten 4.45 mb
Download

Zur Seite of 33

Summary
  • Bretford LAP30EULBA - page 1

    LAP30EULBA LAP30EULFR NOTEBOOK CART ASSEMBL Y WITH TIMER Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER REPLACEMENT Parts List Qt y . Part No. Description 1 LAP30EULBA Cart Assembly , e-units at back LAP30EULFR Cart Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of cart ...

  • Bretford LAP30EULBA - page 2

    clip DET AIL 'A' DET AIL 'B' E-Unit power cord timer assembly bottom shelf Front View bracket assembly bracket assembly ...

  • Bretford LAP30EULBA - page 3

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 18 screws (2 per shelf) from r ...

  • Bretford LAP30EULBA - page 4

    DET AIL 'D' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab ...

  • Bretford LAP30EULBA - page 5

    Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the rear of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window . 4. Grip the top and tilt to the upright position, underneath top panel bracket. When repositi ...

  • Bretford LAP30EULBA - page 6

    Step 6 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'E' Step 7 Reinstall 18 scre ...

  • Bretford LAP30EULBA - page 7

    Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AIL 'A'). DET AIL 'A' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET AIL 'B' mounting tab ...

  • Bretford LAP30EULBA - page 8

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the ...

  • Bretford LAP30EULBA - page 9

    DET AIL 'C' DET AIL 'D' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. re ...

  • Bretford LAP30EULBA - page 10

    Step 4 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'F' Step 5 Reinstall 18 screw ...

  • Bretford LAP30EULBA - page 11

    Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit power switch shou ...

  • Bretford LAP30EULBA - page 12

    E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AIL 'A'). DET AIL 'A' DET AIL 'B' mounting tab ...

  • Bretford LAP30EULBA - page 13

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip ...

  • Bretford LAP30EULBA - page 14

    DET AIL 'C' DET AIL 'D' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. rear-right rear-left ...

  • Bretford LAP30EULBA - page 15

    Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window . Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the br ...

  • Bretford LAP30EULBA - page 16

    notch tab Step 5 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'E' Step 6 Reinsta ...

  • Bretford LAP30EULBA - page 17

    Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of cart. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be repl ...

  • Bretford LAP30EULBA - page 18

    Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET AIL 'A' DET AIL 'B' bracket assembly bracket assembly front-right front-left ...

  • Bretford LAP30EULBA - page 19

    Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tigh ...

  • Bretford LAP30EULBA - page 20

    TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET AIL 'A' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A'). DET AIL 'B' mounting tab ...

  • Bretford LAP30EULBA - page 21

    Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View). ...

  • Bretford LAP30EULBA - page 22

    Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . The E-Unit bracket assembly shown above, will need to be removed (with a philips screwdriver) to allow the E- Unit to swing back. This will allow the timer cord plug to pass between the E-Unit and rear panel. bottom flange- timer/brack ...

  • Bretford LAP30EULBA - page 23

    Step 5 Install bracket to replacement timer with 2 nut s. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Step 6 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located abo ...

  • Bretford LAP30EULBA - page 24

    Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab DET AIL 'C' Step 8 Reinstall ...

  • Bretford LAP30EULBA - page 25

    TIMER REPLACEMENT : 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 E-Unit power cord timer assembly bottom shelf Front View Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power cords of the E-Units from the timer assembly ...

  • Bretford LAP30EULBA - page 26

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET AIL 'A' DET AIL 'B&a ...

  • Bretford LAP30EULBA - page 27

    DET AIL 'A' Step 3 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A'). DET AIL 'B' mounting tab ...

  • Bretford LAP30EULBA - page 28

    Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/b ...

  • Bretford LAP30EULBA - page 29

    Step 6 Remove 2 screws that secure timer to bracket. Step 7 Install bracket to replacement timer with 2 nut s. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Timer vents & bracket must be attached as shown. ...

  • Bretford LAP30EULBA - page 30

    Step 8 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutouts. notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf wit ...

  • Bretford LAP30EULBA - page 31

    DET AIL 'C' Step 10 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS . Step 1 1 Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When repositioned ...

  • Bretford LAP30EULBA - page 32

    1 1 2 2 1 1 1 1 1 1 22 15 19 11 7 16 20 8 12 AUX. 1 3 AUX. 2 4 17 21 13 9 18 22 10 14 AUX. 3 1 5 AUX. 4 2 6 23 27 24 28 25 29 26 30 AUX. 5 AUX . 6 LABEL INST ALLA TION: E-Unit at front suggested label direction suggested installation of labels peel off and attach corresponding labels to shelves and E-Units. shelf E-Unit E-Unit E-Unit at rear ...

  • Bretford LAP30EULBA - page 33

    Part #031-6567 Rev . 12.22.08 CZ P AD LOCK - DOOR: Open Lock The First T ime 1) Set the combination to 0-0-0-0 2) Depress shackle and pull open. T o Set Y ou Own Combination **REMEMBER: Combination can only be set when lock is open. 1) Insert “reset” tool (included in package) in hole on side of lock. 2) Push key in and turn key 90 degrees in e ...

Produzent Bretford Kategorie Food Warmer

Dokumente, die wir vom Produzenten des Geräts Bretford LAP30EULBA erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Bretford
- Bedienungsanleitungen LAP30EULBA
- Produktkarten Bretford
- Informationsbroschüren
- oder Energieetiketten Bretford LAP30EULBA
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Bretford LAP30EULBA.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Bretford LAP30EULBA, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Bretford LAP30EULBA. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Bretford LAP30EULBA ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Bretford LAP30EULBA, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Bretford LAP30EULBA hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Bretford LAP30EULBA verständlich ist.

Eine gänzliche Bedienungsanleitung von Bretford sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Bretford LAP30EULBA bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Bretford LAP30EULBA befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Bretford LAP30EULBA, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Bretford LAP30EULBA - die uns die ersten Schritte während der Nutzung von Bretford LAP30EULBA erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Bretford LAP30EULBA hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Bretford LAP30EULBA im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Bretford LAP30EULBA?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bretford LAP30EULBA nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bretford LAP30EULBA hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)