-
SoundCraft Spirit Folio 4 - page 1
...
-
SoundCraft Spirit Folio 4 - page 2
Thank you for buying a SPI RIT FOL IO 4 mixer, brought t o y ou with p ride by t he S PIRI T team of P eter, Graham, Malcolm, M artin, P eter, B rian, George, Colin, T ony, Jam es, M ukesh, Andy , Candy and Simon. W e hope you have as much fun as we did! Owni ng a SPIRIT console brings you the expertise and suppor t of one of the industr y’s lead ...
-
SoundCraft Spirit Folio 4 - page 3
...
-
SoundCraft Spirit Folio 4 - page 4
e ...
-
SoundCraft Spirit Folio 4 - page 5
...
-
SoundCraft Spirit Folio 4 - page 6
e ...
-
SoundCraft Spirit Folio 4 - page 7
...
-
SoundCraft Spirit Folio 4 - page 8
e ...
-
SoundCraft Spirit Folio 4 - page 9
...
-
SoundCraft Spirit Folio 4 - page 10
e This group of switches selects a choice of sources for the STEREO LISTEN switch (see below). Any combination may be selected as required. A built-in 1kHz OSCILLA T OR provides a test tone for system tests or aligning T ape Machines. Press the switch to turn ON the oscillator and feed a 1kHz tone to the MIX and GROUP outputs at a fixed level. DON? ...
-
SoundCraft Spirit Folio 4 - page 11
Normally the Monitor and Phones outputs receive either the Mix signal or the 2 T rack Return signal, depending on the position of the MIX/2TK switch. STEREO LISTEN provides a further choice of sources from Aux Sends 5-8, Groups 1-4 or Stereo Returns PFL. The switches are non-interlocking to allow several sources to be monitored simultaneously . The ...
-
SoundCraft Spirit Folio 4 - page 12
You will probably use your SP IRI T FOLIO 4 with a wide r ange of different types of sound source, and these will be at varying signal levels. It is i m port ant to set the GAIN of the inputs corr ectly to give the best perfor mance. Set up the individual mono input channels as follows: • • Plug in the chosen source (usually the MI C i nput for ...
-
SoundCraft Spirit Folio 4 - page 13
While the connec tions to the FOLIO 4 for PA wor k are quite s traightf orward, recording is rather more dem anding because the m ixer is not only required to mix down input s i gnals but a l so t o provide a monitor mix for art ists to hear previously recorded tracks when overdubbing new parts. A typical 4-track set- up is as fo llows : • • Co ...
-
SoundCraft Spirit Folio 4 - page 14
Balan ced Input 2. Hot(+v e) 3. Cold( -ve) 1. Screen MONO INPUT CHANNEL Unbala nced Input 1. Screen 2. Hot(+ ve) Link 3 to 1 Hot (+ve) Cold (-ve) Gnd/Screen Signal Gnd/Screen Gnd/Screen Tip Ring Sleeve Unbalanced Balanced Ba l anced M i c I nput - XLR 3-Pole Jac k Unbal anced M i c Input - XL R MIC INPUT The mic i nput socket at the rear of the mix ...
-
SoundCraft Spirit Folio 4 - page 15
INSERT The pre-EQ Inser t is a break point in the channel signal path. I t allows the signal to be taken out of the mixer, through an external piece of equipment and then back into the m ixer to continue thr ough to the f inal output. The Insert is a 3-pole ‘A’ gauge jack socket, wh ich is normally bypassed. When a jack is insert ed, th e signa ...
-
SoundCraft Spirit Folio 4 - page 16
These contr ol s route the input channel signal to any one or more of eight Auxiliary busses. These combine th e sends from each channel, mixing them to separate outputs on the rear of the mixer. Since they are independent of the main outputs t hey can provide additional sources for foldback, effects processors or ex t ra loudspeaker ‘fil ls’. ...
-
SoundCraft Spirit Folio 4 - page 17
STEREO INPUT CHANNE LS 13-2 0 STEREO INPUT L & R These i nputs accept 3-pole ‘A’ gauge (TRS) jacks. Use t hese inputs for sources such as keybo a rds, d rum mac hines, sy nths, tape machi nes or as re turn s from processi n g un it s. The inputs are BALANCED for l ow noise and immunit y from i nterf erence, but you can use UNBALANCED source ...
-
SoundCraft Spirit Folio 4 - page 18
This send can be pre- fade and used in the same way as Aux Sends 1 & 2 for Foldback or as a Monitor feed, but for Effect s it is more appropriate for the Aux Send to fade up and down with the fader (PO S T-FADE). A M aster Section AUX3 PRE switch allows you to sw i tch all channel Aux 3 sends f rom pre- to post-fade acros s the whole mixer as r ...
-
SoundCraft Spirit Folio 4 - page 19
Just like the P FL switches on the channels, you can monitor the AUX 1-4 outputs by pressing the latching AFL switch. This rout es the AUX out put signal to the MO NITOR or P HONES, rep lacing any existing signal (norm ally the Monitor receives e i ther MI X or the Tape Ret urn, depending on the position of the MIX switch - see bel ow). The RIGHT P ...
-
SoundCraft Spirit Folio 4 - page 20
The three colour PPM Bargraph Meters normally fol low the Monitor selection to show the level of the S t ereo MIX outputs or 2-T rack Tape Ret urns, giving y ou a constant warning of exc essive peaks in the signal which might cause overloading. Alternatively they may be switc hed t o monitor a choice of Group or Auxiliary output s, the Stereo Retur ...
-
SoundCraft Spirit Folio 4 - page 21
STEREO PUBLIC ADDRESS In this basic PA Set-up, v arious sources are connec ted to the inputs, microphones to Mic inputs and keyboards etc. to L ine inputs. Note that som e gu itars will not produce suff icient level for a direct connect ion, and will requi re a Direct In j ection (DI ) box connected via the microphone input . The output is taken fr ...
-
SoundCraft Spirit Folio 4 - page 22
PUBLIC ADDRESS - STEREO + SIDE F I L L OR CENTRE F E ED In this second example an additional side fill or cent re speaker cluster is driven from Aux 7 & 8, Aux 4 or Aux 3 switched to Post -fade, with individual rotary fader contro l. Aux 7 & 8 woul d be ideal, since a Group can also feed these Aux sends if required. The individual channel A ...
-
SoundCraft Spirit Folio 4 - page 23
STEREO RECORDING The console m ay be used for 2-T rack or basic m ul titrac k recording, l ive or in the stud i o. T he set up is s i mi lar to the previous ex amples, but w i th the Mix L/ R Output feeding a 2-Track Tape M achine. T he tape out puts are brought back to the console for monitoring via t he 2-Track Tape Returns. Aux 1, 2 or 3 (global ...
-
SoundCraft Spirit Folio 4 - page 24
4-Track Reco rd ing The console m ay also be used for 4- T r ack recording. T he set up i s sim i lar to the previous examp l e, but with a 4-track recor der fed from the Group Outputs and brought back for monitoring via 4 line inputs. In this case a compressor /limiter is shown applied to one o f the mic channels via the insert. 23 ...
-
SoundCraft Spirit Folio 4 - page 25
AFL (After Fade Liste n) a function t hat allows the ope rator to mo nitor the post -fa de signa l in a cha nnel indep endent ly of the main mix. Balance the rela tive levels of the left and r ight c hann els of a stereo s ignal. Balanced a method of aud io conne ction which ‘balanc es’ the signal bet wee n two wires and a scre en which ca rrie ...
-
SoundCraft Spirit Folio 4 - page 26
(Measured 20Hz - 20kHz RMS) Ω (inc. No ise @ 1kHz) (@ 1kHz, typical) Ω 25 ...
-
SoundCraft Spirit Folio 4 - page 27
1 19.37 (4.70") 777.00 (30.59") 470.00 (18.50") 124.00 (4.88") 17.00 (0.67") 410.00 (16.14") Ω Ω Ω 26 ...
-
SoundCraft Spirit Folio 4 - page 28
3 1 2 MONO INPUT CHANNEL STEREO INPUT CHANNEL STEREO RETURNS ▲ ▲ ➚ ➚ ➚ ➚ MASTER SECTION SY STE M BLOCK DIAGRAM 27 ...
Haben Sie eine Frage bezüglich SoundCraft Spirit Folio 4?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit SoundCraft Spirit Folio 4 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit SoundCraft Spirit Folio 4 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.