Bedienungsanleitung Makita DCS230T

20 Seiten 1.1 mb
Download

Zur Seite of 20

Summary
  • Makita DCS230T - page 1

    Instruction Manual Important: Read this instruction manual carefully bef ore putting the chain saw int o operation and strictly obser v e the saf ety regulations! Only persons who hav e completed training in working from ele vat ed platf orm s (cherr y pic k ers, lifts), f rom platforms mounted on ladders or who are pro ficient in climbing with rop ...

  • Makita DCS230T - page 2

    2 Thank y ou for pur cha sing a MAKIT A pr oduct! Congratulations on choosing a MAKIT A chain s a w! We are confident that you will be satisfied with this moder n piece of equipment. The DCS230T and DCS232T (T ophandle) are very light and handy chain saws with the handles on the top. These models were dev eloped espe- cially for tree surgery and ca ...

  • Makita DCS230T - page 3

    3 Symbols Y ou will not ice the f ollowing symbols on the chain saw and i n the instruction manual: Read instr uction manual and follow the warning- and safety precautions! I/ST OP -switch (shor t-circuit switch) Chain brak e War nin g This saw is to be used by properly trained operators only . Stop engine! Fuel and oil mix ture P articular care an ...

  • Makita DCS230T - page 4

    4 SAFETY PRECA UTIONS CA UTION: This chain saw is designed especially for tree care and surgery . All work with this chain saw is to be carried out by pr operly trained persons only . O bserve all literature, procedures and recommendations from the rel- evant pr ofessional organisation. Failure to do so constitutes a high acci dent risk! W e recomm ...

  • Makita DCS230T - page 5

    5 Before starting work the chain saw must be checked f or perfect function and operating safety accor ding to the prescri ptions. Check especially the function of the chain br ake, the correct mounting of the guide bar , the correct shar pening and tightening of the chain, the firm m ounting of the sprocket guard, the easy motion of the throttle le ...

  • Makita DCS230T - page 6

    6 - The saw must be running whenev er y ou remov e the chain saw f rom the wood. - When performing several cuts the throttle lev er mus t be released in between. - Be careful when cutting splintery wood. Cut pieces of wood ma y be pulled along (risk of injuries). - When cutting with the upper edge of the guide bar , the chain saw ma y be pushed in ...

  • Makita DCS230T - page 7

    7 Fir st aid For the e vent of a possible accident, please make sure that a first aid kit is always immediately av ailab le close by . Immediately replace any items used from the first aid box. When calli ng for help, give t he fo ll owing inf ormation: - Place of the accident - What happened - Number of injured people - Kind of injuries - Y our na ...

  • Makita DCS230T - page 8

    8 Denomination of compo nents 1 Rear handle 2 Safety l ocking b utton (throttle loc k) 3 Throttle le ver 4 Hand guard (releas e for chain brake) 5 Chain 6 Guide bar 7 Guide bar case 8 Retaining nuts 9 Chain catch (safety device) 10 Sp ro cke t c o ve r 11 Muf fler 12 Spark plug 13 F ront grip (tubular handle) 14 Star ter grip 15 I/ST OP-swi tch (s ...

  • Makita DCS230T - page 9

    9 P o sition the guide bar (7). Lift the chain (9) over the sproc ket (10). Usi ng y our right hand, guide the chain into the top guide groov e (11) on the guide bar . Note that the cut ting edges along th e top of the chain must point in the direction of the arrow ! Pull the chain (9) around the nose (12) of the guide bar in the direction of the a ...

  • Makita DCS230T - page 10

    10 Chain brake The DCS230T and DCS232T come with an inertia chain brake as standard equipment. If kick- back occurs due to contact of the guide-bar tip wit h wood (see “SAFETY PRECAUTIONS”), the chain brake will stop the chain th rough iner tia if the kickback is sufficiently str ong. The chain will stop within a fraction of a second. The chain ...

  • Makita DCS230T - page 11

    11 Chain oil Use an oil with adhesive additiv e for lubricating the chain and gu ide bar . The adhesiv e additiv e pre v ents the oil from being fl ung off the chain too quickly . W e recomm end the us e of chain oil which is bio-degradable in order to protect the en vironment. The use of bio-degr ad able oi l may e ven be required by local regulat ...

  • Makita DCS230T - page 12

    12 T o ensure troublefree operation of the oil pump the oil guide groov e at the housing ( 2) and the oil inlet bore in t he guide bar (3) must be cleaned regularly . Chec king the chai n lubricat ion Nev er work with the chain sa w without sufficient chain l ubrication. Otherwise the serv ice lif e of the chain and guide bar will be reduced. Befor ...

  • Makita DCS230T - page 13

    13 Chec king the c hain b rake Do not work with the c hain saw without first c hecking the c hain brake! Star t the engine as described (make sure you ha ve a good foot ing, and place the chain saw on t he ground in such a wa y that the guide bar is free of contact). Grasp the tub ular handle firmly with one hand and hold the grip with the other . ...

  • Makita DCS230T - page 14

    14 All cutters must be sharpened to the same angle, 30° . Diff erent angles result in a roughly , irregu- larly ru nning chain, increase wear and tear and cause chain beakage . The 85° front rake of the cu tter results from the cu t depth of the round file . If the proper file is used in the right manner , the correct front rake will be obtained ...

  • Makita DCS230T - page 15

    15 Cleaning the g uide bar , lubricating th e sproc ket nose CA UTION: Protective g loves m ust be worn . Regularly inspect the bearing surfaces of the guide bar f or damage, and clean them with a suitab le tool. Sprocket nose type: If the sa w is used intensiv ely it will be necessar y to lubricate the retur n sprocket bearings regularly (once a w ...

  • Makita DCS230T - page 16

    16 Electr ode gap The electrode gap must be 0.6 – 0.7 mm. Cleaning th e inlet p ort of the cooling air Unscrew f o ur screws (2). Remove recoil star ter (3). Clean the inlet por t (4) and the cylinder fins. Cleaning th e muffl er CA U TION: If the en gine is hot there is a risk of burning. Wear pr otective glo ves. Remove the sprock et cov er (se ...

  • Makita DCS230T - page 17

    17 Instructions for periodic main tenance T o ensure long lif e, prev ent damage and ensur e the full functioning of the safety f eatures the follo wing maintenance must be pe rformed regularly . Guaran- tee claims can be recognized only if this wor k is performed r egular ly and prope rly . F ailure to per form the prescr ibed maintenan ce work ca ...

  • Makita DCS230T - page 18

    18 Guaran tee MAKIT A guarantees the highest quality and will theref ore reimburse all costs for repair by repl acement of damaged par ts resulti ng from mater ial or pro- duction f aults occurring within the guarantee per iod after purchas e. Please note that in some countries par ticu lar guarantee co nditions may e xist. If you hav e an y questi ...

  • Makita DCS230T - page 19

    19 ...

  • Makita DCS230T - page 20

    Makita Corporation Anjo Aichi Japan 884570 A5 ...

Produzent Makita Kategorie Chainsaw

Dokumente, die wir vom Produzenten des Geräts Makita DCS230T erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Makita
- Bedienungsanleitungen DCS230T
- Produktkarten Makita
- Informationsbroschüren
- oder Energieetiketten Makita DCS230T
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Makita DCS230T.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Makita DCS230T, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Makita DCS230T. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Makita DCS230T ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Makita DCS230T, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Makita DCS230T hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Makita DCS230T verständlich ist.

Eine gänzliche Bedienungsanleitung von Makita sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Makita DCS230T bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Makita DCS230T befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Makita DCS230T, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Makita DCS230T - die uns die ersten Schritte während der Nutzung von Makita DCS230T erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Makita DCS230T hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Makita DCS230T im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Makita DCS230T?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Makita DCS230T nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Makita DCS230T hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)