Bedienungsanleitung Zanussi ZGF 642

18 Seiten 0.15 mb
Download

Zur Seite of 18

Summary
  • Zanussi ZGF 642 - page 1

    2 GAS HOB MODEL ZGF 642 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance ...

  • Zanussi ZGF 642 - page 2

    3 Important Safety Infor mation You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 521313 Installation ● This hob must be installed by qualified personnel, according to the manufacturer ’ s instructions and to the relevant British Standards. ● Any gas ...

  • Zanussi ZGF 642 - page 3

    4 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V oltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications Guide to Use the instructions The following symbols will be found in the text to guide you throughout ...

  • Zanussi ZGF 642 - page 4

    5 1. Hob Top 2. Auxiliary Burner 3. Semi-rapid Burners 4. Rapid Burner 5. Control knob for front left burner (auxiliary) 6. Control knob for back left buner (semi-rapid) 7. Control knob for back right burner (semi-rapid) 8. Control knob for front right burner (rapid) 1 3 4 5 6 7 8 Description of the Hob INSTALLATION Any gas installation must be car ...

  • Zanussi ZGF 642 - page 5

    6 HOB BURNERS T o light a burner , turn the relevant knob anticlockwise to maximum position and push down the knob to ignite. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically . T o ensu ...

  • Zanussi ZGF 642 - page 6

    7 Befor e any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing ...

  • Zanussi ZGF 642 - page 7

    8 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORT ANT: If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a char ge will be made even if the appliance is under guarant ...

  • Zanussi ZGF 642 - page 8

    9 Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929929 Y our call will be routed to your local Service Force Centre. For further details, please see the accompanying Customer Care Booklet. ZANUSSI GUARANTEE CONDITIONS W e, Zanussi, undertake that if, within 24 months ...

  • Zanussi ZGF 642 - page 9

    10 OVERALL DIMENSIONS W idth: 580 mm. Depth: 510 mm. Height: 72 mm. W eight: 12 Kg. CUT OUT DIMENSIONS W idth: 560 mm. Depth: 480 mm. Thickness: 30 mm. Ignition HT Spark Spark Generator Ispra Control's BF 50046-06 , 220-240V 0.6 V A T 120 Spark Gap Fixed Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Fr ont Left Burner (auxiliar ...

  • Zanussi ZGF 642 - page 10

    11 Important safety requir ements 650 mm 420 mm 420 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 420 mm 100 mm 420 mm 50 mm 55 mm 50 mm I CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE FO 0813 FO 0812 700 mm This hob must be installed in accordance with the Gas Saf ...

  • Zanussi ZGF 642 - page 11

    12 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow It is important to install the elbow correctly , with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. FO 0814 Gas Connection Connection to the gas supply should be with either r ...

  • Zanussi ZGF 642 - page 12

    13 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 FO 0199 a Fitting the Hob into the w orktop Carry out the building in of the hob as follows: • put the seals supplied with the hob on the edges of the cut out, as shown in the diagram, taking care that the seals meet without overlapping; • plac ...

  • Zanussi ZGF 642 - page 13

    14 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 240V 50 ...

  • Zanussi ZGF 642 - page 14

    15 W iring Diagram 1. TAPS IGNITOR SWITCHES 2. IGNITOR UNIT 1 2 L N 0 220 240 1 2 3 4 ...

  • Zanussi ZGF 642 - page 15

    16 Fault Finding Pr eliminar y Electrical Systems Check A. EAR TH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and ...

  • Zanussi ZGF 642 - page 16

    17 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro ...

  • Zanussi ZGF 642 - page 17

    18 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished ...

  • Zanussi ZGF 642 - page 18

    19 A: Removal Of Hob Top 1. Remove all control knobs, pan supports, burner caps and burner crowns. 2. Remove 2 screws for each burner . 3. Remove 4 fixing screws from the pan support hinges, and remove the hinges from the hob. 4. Lift hob top at the rear and remove it from the hob. B: Removal Of the Hob Taps (Isolate Electrical Supply) 1. Follow th ...

Produzent Zanussi Kategorie Range

Dokumente, die wir vom Produzenten des Geräts Zanussi ZGF 642 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Zanussi
- Bedienungsanleitungen ZGF 642
- Produktkarten Zanussi
- Informationsbroschüren
- oder Energieetiketten Zanussi ZGF 642
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Zanussi ZGF 642.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Zanussi ZGF 642, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Zanussi ZGF 642. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Zanussi ZGF 642 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Zanussi ZGF 642, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Zanussi ZGF 642 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Zanussi ZGF 642 verständlich ist.

Eine gänzliche Bedienungsanleitung von Zanussi sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Zanussi ZGF 642 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Zanussi ZGF 642 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Zanussi ZGF 642, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Zanussi ZGF 642 - die uns die ersten Schritte während der Nutzung von Zanussi ZGF 642 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Zanussi ZGF 642 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Zanussi ZGF 642 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Zanussi ZGF 642?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Zanussi ZGF 642 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Zanussi ZGF 642 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)