Bedienungsanleitung Stanley Black & Decker CO25

20 Seiten 2.06 mb
Download

Zur Seite of 20

Summary
  • Stanley Black & Decker CO25 - page 1

    CO25 HYDRAULIC CUT -OFF SA W USER MANUAL Safety , Operation and Maintenance © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 34962 2-2015 V er-14 ...

  • Stanley Black & Decker CO25 - page 2

    2 ► CO25 User Manual DECLARATION OF CONFORMITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORMITA Hydraulic Tools _______ _________ _____ _________ ________ _________ ________ _________ ______ I, the undersigned: Ich, der Unterzeichnende: Je soussi gné: El abajo firmante: lo so t ...

  • Stanley Black & Decker CO25 - page 3

    CO25 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer . Please read the following warning. For the nearest authorized and certie ...

  • Stanley Black & Decker CO25 - page 4

    4 ► CO25 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker CO25 - page 5

    CO25 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Review them carefully before operating the tool and before per- forming general maintenance or repairs. ...

  • Stanley Black & Decker CO25 - page 6

    6 ► CO25 User Manual • Never carry the tool or put it down while the wheel is rotating. Make sure it is completely stopped before moving your position or set the tool down. • Do not operate the tool with the wheel guard removed. • Keep the handles dry , clean and free of oil at all times. • Operate the tool in well ventilated areas only . ...

  • Stanley Black & Decker CO25 - page 7

    CO25 User Manual ◄ 7 The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory . Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use. SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TI ...

  • Stanley Black & Decker CO25 - page 8

    8 ► CO25 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker CO25 - page 9

    CO25 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS 4-6 1 ...

  • Stanley Black & Decker CO25 - page 10

    10 ► CO25 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max. uid temp ...

  • Stanley Black & Decker CO25 - page 11

    CO25 User Manual ◄ 1 1 PREOPERA TION PROCEDURES CHECK THE POWER SOURCE Careful inspection of the tool and hydraulic system before st ar tu p i s important for safe, reliable operation of the tool. 1. Using a calibrated owmeter and pressure gauge, check that the hydraulic power source develops a ow of 7–9 gpm (26–34 lpm) at 2000 psi (140 ...

  • Stanley Black & Decker CO25 - page 12

    12 ► CO25 User Manual If excessive vibration or any other defect is detected, stop the tool immediately and determine the cause. Do not use the tool until the problem is corrected. GENERAL OPERA TION HANDHELD CONFIGURA TION: 1. Whenever possible, clamp or hold down the work and support it securely on both sides of the cut. 2. Press the safety cat ...

  • Stanley Black & Decker CO25 - page 13

    CO25 User Manual ◄ 13 PERIODIC MAINTENANCE For maximum performance and reliability of the tool, peri- odically check the following components. THRUST COLLAR AND INSIDE/OUTSIDE COLLAR INSPECTION Periodically inspect the thrust collar for damage when you remove the cut-off wheel (refer to Cutof f Wheel Replace- ment). 1. Remove the key and thrust c ...

  • Stanley Black & Decker CO25 - page 14

    14 ► CO25 User Manual CUT OFF WHEEL REPLACEMENT 1. Move the hydraulic system control valve to the Off posi- tion. 2. Disconnect the hydraulic hoses from the tool (rst the input (supply) hose, then the output (return) hose). 3. Install the inside collar and blotter , rotate the collar to align the slot in the collar with the pin on the thrust c ...

  • Stanley Black & Decker CO25 - page 15

    CO25 User Manual ◄ 15 NO TICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all couplers are wiped clean before connection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydraulic tools. Failure to do so may ...

  • Stanley Black & Decker CO25 - page 16

    16 ► CO25 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diag- nosing faults in operation of the wrench, always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the tool as listed in the following table. Use a ow meter kn ...

  • Stanley Black & Decker CO25 - page 17

    CO25 User Manual ◄ 17 Wheel Capacity ............................................................................................................................................. 14-inch/15.6 cm Weight .................................................................................................................................................. ...

  • Stanley Black & Decker CO25 - page 18

    18 ► CO25 User Manual For Parts to Handle Extension Kit, See Accessories on Page 17 D C B A D C B A 1 3 4 5 6 7 8 1 2 3 4 5 6 7 8 2 NOTES: HYDRAULIC TOOLS NOTE: ALL DIMENSIONS ARE GIVEN IN INCHES AND DEFINE THE FINISHED PART. TOLERANCES AND SURFACE ROUGHNESS IS SPECIFIED BELOW (EXCEPT AS NOTED): WEIGHT: LBS 49.0 SCALE: 0.500 DRAWN BY: MATERIAL CO ...

  • Stanley Black & Decker CO25 - page 19

    CO25 User Manual ◄ 19 • Denotes Part in Seal Kit Item No. Part No. Qty Description 1 001 12 1 QUAD RING* 2 00175 4 O-RING* 3 00563 1 ROLL PIN 4 00720 1 SETSCREW 5 00772 1 WOODRUFF KEY 7 01594 2 WASHER 8 01604 2 O-RING* 9 01714 1 HEX JAM NUT CCW (RH) 03012 1 HEX JAM NUT CW (LH) 10 02649 3 HANDLE BAR RET AINER 11 02654 1 HANDLE BAR 12 02688 8 CAP ...

  • Stanley Black & Decker CO25 - page 20

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Produzent Stanley Black & Decker Kategorie Saw

Dokumente, die wir vom Produzenten des Geräts Stanley Black & Decker CO25 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Stanley Black & Decker
- Bedienungsanleitungen CO25
- Produktkarten Stanley Black & Decker
- Informationsbroschüren
- oder Energieetiketten Stanley Black & Decker CO25
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Stanley Black & Decker CO25.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Stanley Black & Decker CO25, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Stanley Black & Decker CO25. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Stanley Black & Decker CO25 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Stanley Black & Decker CO25, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Stanley Black & Decker CO25 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Stanley Black & Decker CO25 verständlich ist.

Eine gänzliche Bedienungsanleitung von Stanley Black & Decker sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Stanley Black & Decker CO25 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Stanley Black & Decker CO25 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Stanley Black & Decker CO25, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Stanley Black & Decker CO25 - die uns die ersten Schritte während der Nutzung von Stanley Black & Decker CO25 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Stanley Black & Decker CO25 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Stanley Black & Decker CO25 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Stanley Black & Decker CO25?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Stanley Black & Decker CO25 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Stanley Black & Decker CO25 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)