Bedienungsanleitung Campbell Hausfeld WF2034

24 Seiten 0.56 mb
Download

Zur Seite of 24

Summary
  • Campbell Hausfeld WF2034 - page 1

    Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. IN970300AV 1 ...

  • Campbell Hausfeld WF2034 - page 2

    2 Wire Feed Arc Welder Always keep a fire extinguisher accessible while performing arc welding operations. ● Before starting or servicing any electric arc welder, read and understand all instructions. Failure to follow safety precautions or instructions can cause equipment damage and/or serious personal injury or death. ● All installation, main ...

  • Campbell Hausfeld WF2034 - page 3

    LOCATION Selecting the proper location can significantly increase performance, reliability and life of the arc welder. ● For best results locate the welder in an environment that is clean and dry. ● Store flux core wire in a clean, dry location with low humidity to preserve the flux wire coating. ● The use of an extension cord is not recommen ...

  • Campbell Hausfeld WF2034 - page 4

    Flux Core Wir e Installation Welding power is applied to the output terminals, feed roll, ground clamp, gun cable connection and welding wire even when the gun switch is not activated. Do not touch these parts when the welding machine is on. NOTE: Before installing welding wire, be sure that the diameter of the welding wire matches the contact tip ...

  • Campbell Hausfeld WF2034 - page 5

    Metal Heat Thickness Setting 5 Model WF2034 If heating, welding, or cutting materials that are galvanized, zinc plated, lead, or cadmium plated refer to the General Safety Information Section for instructions. Extremely toxic fumes are created when these metals are heated. 4. Connect the ground clamp to the work piece or workbench (if metal). Make ...

  • Campbell Hausfeld WF2034 - page 6

    WIRE TYPE AND SIZE The correct choice of wire type involves a variety of factors, such as welding position, work piece material type, thickness, and condition of surface to be welded. The American Welding Society, AWS, has set up certain requirements for each type of wire. The AWS classification for self-shielding wire (Gasless process) is a multi ...

  • Campbell Hausfeld WF2034 - page 7

    Model WF2034 W elding Guidelines (Continued) Figure 10 - Multiple Weld Passes PUSH VS PULL TECHNIQUE The type and thickness of the work piece dictates which way to point the gun nozzle. For thin materials (18 gauge and up), the nozzle should point out in front of the weld puddle and push the puddle across the workpiece. For thicker steel, the nozzl ...

  • Campbell Hausfeld WF2034 - page 8

    8 Wire Feed Arc Welder T r oubleshooting Chart - W elder Symptom Possible Cause(s) Corrective Action 1. Duty cycle exceeded 2. Poor ground clamp connection 3. Defective power switch 4. Blown breaker or fuse 1. Wrong size gun tip 2. Gun liner clogged or damaged 3. Gun tip clogged or damaged 4. Feed roller worn 5. Not enough tension Slag inside gun n ...

  • Campbell Hausfeld WF2034 - page 9

    9 Model WF2034 Heat Selector Switch Thermal Breaker T1 T2 S2 6 5 2 4 1 432 1 L2(N) L1 S4 Max Min White Black Green Ground M Gun T rigger S4 - Thermal Breaker To r c h _ _ + + AC to DC Converter (-) T o Work Clamp (+) WF2034 Wiring Diagram Limited 5-3-1 W arranty 1. Duration: The manufacturer warrants that it will repair, at no charge for parts or l ...

  • Campbell Hausfeld WF2034 - page 10

    10 Wire Feed Arc Welder For Replacement Parts, call 1-800-746-5641 Address parts correspondence to: The Campbell Group Attn: Parts Department 100 Production Drive Harrison, Ohio 45030 Please provide following information: - Model number - Serial number (if any) - Part description and number as shown in parts list 1 Torch assembly and hose WC601200A ...

  • Campbell Hausfeld WF2034 - page 11

    11 Glossary of W elding T erms AC or Alternating Current - electric current that reverses direction periodically. Sixty cycle current travels in both directions sixty times per second. Arc Length - the distance from the end of the electrode to the point where the arc makes contact with the work surface. Base Metal - the material to be welded. Butt ...

  • Campbell Hausfeld WF2034 - page 12

    Notes 12 Wire Feed Arc Welder Model WF2034 www.chpower.com ...

  • Campbell Hausfeld WF2034 - page 13

    Sírvase leer y guardar estas instrucciones.Lea con cuidado antes de tratar de armar, instalar, manejar o darle servicio al producto descrito en este manual. Protéjase Ud. y a los demás observando todas las reglas de seguridad. El no seguir las instrucciones podría resultar en heridas y/o daños a su propiedad.Guarde este manual como referencia. ...

  • Campbell Hausfeld WF2034 - page 14

    14 Sp NOTA: Ésto le indica cualquier información adicional sobre el producto o el uso adecuado del mismo. Siempre mantenga un extingidor de incendio accesible cuando esté soldando con arcos eléctricos. ● Antes de encender o darle servicio a las soldadoras eléctricas de arco, debe leer y comprender todas las instrucciones. Si no sigue las med ...

  • Campbell Hausfeld WF2034 - page 15

    Safe Handling of Compressed Gases in Cylinders CGA Pamphlet P-1, — Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202 Cutting And Welding Processes NFPA Standard 51B, — National Fire Protection Association, Batterymarch Park, Quicy, MA 02269 Safe Practices For Occupational And Educational Eye And Face Prote ...

  • Campbell Hausfeld WF2034 - page 16

    2. Para desactivarle el seguro al carre- te, oprímalo y gírelo en sentido contrario a las agujas del reloj 1/4 . Ahora puede sacarle la perilla, el resorte y el separador. 3. Afloje el tornillo que le suministra tensión al alambre en el mecanismo. Ésto le permite meter con la mano el alambre en la pistola. 4. Coloque el carrete de alambre en el ...

  • Campbell Hausfeld WF2034 - page 17

    17 Modelo WF2034 soldadores de la oscuridad adecuada según las especificaciones dadas a continuación, ropa resistente al fuego, guantes de cuero para soldar y protección para los pies. El alambre para soldadura está cargado siempre cuando la soldadora está encendida - esté el gatillo oprimido o no. Si piensa calentar soldar o cortar materiale ...

  • Campbell Hausfeld WF2034 - page 18

    18 Sp Soldadora Con Arco Con Alambre Continuo Instrucciones para Soldar General Esta línea de soldadoras utiliza el proceso de soldadura por arco eléctrico con fundente (sin gas). La soldadura se debe proteger contra contaminantes en el aire mientras se esté derritiendo. Pa- ra soldar con un alambre con fundente revestido se utiliza un alambre c ...

  • Campbell Hausfeld WF2034 - page 19

    19 Sp Modelo WF2034 Figura 9 - Pasos Cubierta Relleno Raíz Instrucciones para Soldar (Continuaci ó n) TECNICA USADA PARA SOLDAR El tipo de material y el grosor de la pieza que va a soldar determinan la dirección en que debe colocar la boquilla de la pistola. Para soldar materiales delgados (de calibre 18 o mayores) debe colocar la boquilla en fr ...

  • Campbell Hausfeld WF2034 - page 20

    20 Sp DIAGNOSTICO Diag ó stico de A ver í as-Soldadora Problema Posible(s) Causa(s) Acci ó n a Tomar 1. Excedio el ciclo de trabajo 2. La pinza de conexión a tierra está mal conectada 3. El interruptor está dañado 4. El cortacircuito se activó o el fusible está quemado 1. La boquilla de la pistola es de un tamaño incorrecto 2. El forro de ...

  • Campbell Hausfeld WF2034 - page 21

    1. Duraci ó n: El fabricante garantiza que reparará, sin costo alguno por repuestos o mano de obra la soldadora o la pistola o los cables que estén dañados bien en material o mano de obre, durante los siguientes periodos después de la compra original: Por 5 años: El transformador y rectificador de la soldadora Por 3 años: Toda la soldadora ( ...

  • Campbell Hausfeld WF2034 - page 22

    1 Ensamblaje del soplete y manguera WC601200AJ 1 2 Cuerpo del soplete (piezas posterior y delantera) WC600401AV 1 3 Accesorio del forro WC600403AV 1 4 Boquilla WT502100AJ 1 5 Interruptor del gatillo WC600402AV 1 6 Tuerca de torsión del soplete WC600404AV 1 7 Pinza (no incluye el cordón) WC100000AV 1 8 Cable para soldar 8 AWG (6 pies, 1,83 metros) ...

  • Campbell Hausfeld WF2034 - page 23

    23 Glosario de terminolog í a usada por soldador es CA o Corriente Alterna - corriente eléctrica que cambia de dirección periódicamente. Corriente de 60 ciclos se desplaza en ambas direcciones 60 veces por segundo. Longitud del Arco - la distancia entre el extremo del electrodo y el punto de contacto con la superficie de trabajo. Metal B á sic ...

  • Campbell Hausfeld WF2034 - page 24

    Notas Soldadora Con Arco Con Alambre Continuo Modelo WF2010 ...

Produzent Campbell Hausfeld Kategorie Welder

Dokumente, die wir vom Produzenten des Geräts Campbell Hausfeld WF2034 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Campbell Hausfeld
- Bedienungsanleitungen WF2034
- Produktkarten Campbell Hausfeld
- Informationsbroschüren
- oder Energieetiketten Campbell Hausfeld WF2034
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Campbell Hausfeld WF2034.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Campbell Hausfeld WF2034, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Campbell Hausfeld WF2034. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Campbell Hausfeld WF2034 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Campbell Hausfeld WF2034, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Campbell Hausfeld WF2034 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Campbell Hausfeld WF2034 verständlich ist.

Eine gänzliche Bedienungsanleitung von Campbell Hausfeld sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Campbell Hausfeld WF2034 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Campbell Hausfeld WF2034 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Campbell Hausfeld WF2034, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Campbell Hausfeld WF2034 - die uns die ersten Schritte während der Nutzung von Campbell Hausfeld WF2034 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Campbell Hausfeld WF2034 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Campbell Hausfeld WF2034 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Campbell Hausfeld WF2034?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Campbell Hausfeld WF2034 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Campbell Hausfeld WF2034 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)