Bedienungsanleitung Audiovox CCS-100

19 Seiten 0.3 mb
Download

Zur Seite of 19

Summary
  • Audiovox CCS-100 - page 1

    ® CCS-100 CCS-100 CCS-100 CCS-100 CCS-100 ELECTR ELECTR ELECTR ELECTR ELECTR O O O O O NIC CRUISE CO NIC CRUISE CO NIC CRUISE CO NIC CRUISE CO NIC CRUISE CO NTR NTR NTR NTR NTR OL OL OL OL OL INST INST INST INST INST ALLA ALLA ALLA ALLA ALLA TI TI TI TI TI O O O O O N M N M N M N M N M ANUAL ANUAL ANUAL ANUAL ANUAL ...

  • Audiovox CCS-100 - page 2

    MANUAL PREPARED AND PROVIDED BY LITEON AUTOMOTIVE CORPORATION INDEX 1. Cruise Control Installation: ..................................................... Parts List ........................................................................... Throttle Connections......................................................... Wiring ........................ ...

  • Audiovox CCS-100 - page 3

    HOW THE CRUISE WORKS The Cruise Module makes "decisions" based upon speed,tachometer, and brake signal information. The control circuit interprets digital speed information from the car's engine control module (VSS) or Magnet Kit and ignition coil output. Brake information comes from the red and purple wires connected to the vehicle& ...

  • Audiovox CCS-100 - page 4

    CRUISE CONTROL M6 x 5/8" long hex head bolt ( 3 ) Servo Assembly ( 1 ) Tie Straps ( 10 ) 1/2" rubber bulkhead grommet ( 1 ) - 1 - - 4 - - 5 - Convoluted tubing ( 1 ) Vacuum hose reducing nipple ( 1 ) Assorted Vacuum T - Connectors Vacuum Hose - Short ( 1 ) Vacuum Hose - Long ( 1 ) - 6 - - 7 - - 8 - - 9 - - 10 - Main Wiring Harness ( 1 ) F ...

  • Audiovox CCS-100 - page 5

    #1 - BROWN - IGNITION POWER #2 - GREY - SPEED #3 - RED - BRAKE #4 - PURPLE - BRAKE #5 - (NOT USED) 1 2 3 4 5 6 7 ON OFF JUMPER LED MANUAL / AUTOMATIC TRANSMISSION SELECT WHEN INSTALLING THIS KIT INTO VEHICLES THAT HAVE A MANUAL TRANSMISSION, YOU MUST REMOVE THE BLACK JUMPER CONNECTOR LOCATED TO THE LEFT SIDE OF DIP SWITCH #1. NOTE: If the vehicle i ...

  • Audiovox CCS-100 - page 6

    Double fold to shorten Crimp with pliers Bend to clear Throttle Cable Throttle Arm Throttle Cable Bead Chain (#20) 3 Bead Connector (#27) UNDER HOOD INSTALLATION Connecting the Cruise Control Cable to the Throttle NOTE: Prior to attaching servo cable to throttle, locate an accessible area to mount the cruise control servo, but do not mount it. Leav ...

  • Audiovox CCS-100 - page 7

    FIG. 8 FIG. 9 FIG. 10 Snap-in Cable Anchor (#19) Module Cable MUST extend past Adaptor Three Bead Connector (#27) Throttle Clip (#26) Bead Chain (#20) Hex Nut & Lockwasher Bead Chain Eyelet Connector (#25) Tube Clamp Cable Anchor Point PEDAL PULL Carburetor Existing Sheet Metal Bracket ALTERNATE FLEX CABLE MOUNTING TECHNIQUE ALTERNATE FLEX CABL ...

  • Audiovox CCS-100 - page 8

    CAUTION ! ATTACH THE CRUISE CONTROL CABLE SO THAT IT PARALLELS THE EXISTING THROTTLE CABLE AS NEARLY AS POSSIBLE. WARNING ! AFTER ATTACHING THE CRUISE CONTROL CABLE TO THE VEHICLE’S THROTTLE, OPERATE THE THROTTLE MANUALLY ( FULL TRAVEL ) FROM BOTH UNDER HOOD AND ACCELERATOR PEDAL TO BE ABSOLUTELY SURE THAT NONE OF THE CABLE ATTACHMENT COMPONENTS ...

  • Audiovox CCS-100 - page 9

    Routing the Main Wiring Harness 1. Locate your vehicle by make, model, and engine size in the included Reference Manual in order to identify the location of the VSS and Tach connection locations. If your make and model cannot be located, then the Magnet Kit must be installed. Follow the installation instructions included in this manual. In all case ...

  • Audiovox CCS-100 - page 10

    1. Choose a flat location on the dashboard that is visible while driving. The location should be very accessible to the driver, allowing easy activation of the switch while operating the cruise control. A template has been provided to confirm that there is adequate space for mounting the switch in the selected location. (Fig.1) 2. After the locatio ...

  • Audiovox CCS-100 - page 11

    Figure 1 Drill 1/4" Dia. holes, (2 places). Carefull y cut-out along dotted lines and place on selected area. DASH BOARD TEMPLA TE Use a file or razor knife to remo ve the material between the 2 holes. Figure 3 CONTROL SWITCH CONNECTIONS CR UISE CONTR OL Figure 2 RED CONNECT OR 1 2 3 4 GREEN BR O WN YELLO W A CCEL ON OFF SET COAST RES DA S H C ...

  • Audiovox CCS-100 - page 12

    ROAD TESTING THE CRUISE CONTROL Be sure to fully test all functions of your new cruise control on a level surface away from predestrian and vehicle traffic. While travelling 35 M.P.H. turn switch on , then press Set button. Unit will engage when Set button is released. To disengage, tap on brake or turn switch off - cruise will disengage. Follow sa ...

  • Audiovox CCS-100 - page 13

    TROUBLE SHOOTING WIRING - 10 PIN CONNECTOR Note : If the brown, green, or yellow wires do not test properly, proceed immediately to the testing of the 4 pin control switch testing. P O S WIRE COLOR FUNCTION 9 Black Always continuity to ground 3 Red Always + 12 VDC 1 Brown + 12 VDC with Ignition switch and cruise control switch ON. O VDC with Igniti ...

  • Audiovox CCS-100 - page 14

    M M M M M A A A A A GNET KIT GNET KIT GNET KIT GNET KIT GNET KIT INST INST INST INST INST ALLA ALLA ALLA ALLA ALLA TI TI TI TI TI O O O O O N N N N N MAGNET AND SPEED SENSOR COIL INSTALLATION The magnets, along with the speed sensor coil provide pulses to calculate road speed for the cruise control. When the drive shaft rotates, the magnets attache ...

  • Audiovox CCS-100 - page 15

    Step 6: While rotating the shaft, carefully snap one wire into one set of magnet slots. Loosely wrap the wire to hold it in place. Snap the second wire into the remaining slots making sure the ends are nearly opposite the first wire, as shown in Figure 4 or 11. Step 7: Carefully pull wires tight, and twist with a pair of pliers, pulling down as you ...

  • Audiovox CCS-100 - page 16

    INST ALLA TION - REAR WHEEL DRIVE VEHICLES EXISTING CABLE OR BRA CKET ON VEHICLE CABLE TIE PULL TIGHT DRILL 3/16" DIA HOLES IN FLOOR P AN OF VEHICLE DRIVE SHAFT 12" MAX. DIST ANCE FROM U-JOINT 1/2" POSITION SPEED SENSOR HORIZONT ALL Y T O ALLOW FOR UP AND DO WN MO TION OF DRIVESHAFT VEHICLE FLOOR CLEARANCE 3/8" F ABRICA TED BRAC ...

  • Audiovox CCS-100 - page 17

    INST ALLA TION - FRONT WHEEL DRIVE VEHICLES TRANSMISSION AXLE HOUSING 3/8" DRILL OR FILE BRA CKET T O FIT EXISTING BOL T WIRES AND MA GNET DIA. OF MOUNTING SURF A CE RIGHT FRONT AXLE ONL Y 1/2" 3/8" Figure 6 Figure 7 Figure 1 1 Figure 8 Figure 9 MA GNET MA GNET Figure 10 -15- ...

  • Audiovox CCS-100 - page 18

    -16- AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned pro ...

  • Audiovox CCS-100 - page 19

    Audiovox Corp., 150 Marcus Blvd., N.Y. 11788 Form No.128-4540C ...

Produzent Audiovox Kategorie Automobile Accessories

Dokumente, die wir vom Produzenten des Geräts Audiovox CCS-100 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Audiovox
- Bedienungsanleitungen CCS-100
- Produktkarten Audiovox
- Informationsbroschüren
- oder Energieetiketten Audiovox CCS-100
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Audiovox CCS-100.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Audiovox CCS-100, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Audiovox CCS-100. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Audiovox CCS-100 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Audiovox CCS-100, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Audiovox CCS-100 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Audiovox CCS-100 verständlich ist.

Eine gänzliche Bedienungsanleitung von Audiovox sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Audiovox CCS-100 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Audiovox CCS-100 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Audiovox CCS-100, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Audiovox CCS-100 - die uns die ersten Schritte während der Nutzung von Audiovox CCS-100 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Audiovox CCS-100 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Audiovox CCS-100 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Audiovox CCS-100?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Audiovox CCS-100 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Audiovox CCS-100 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (1)

Руслан

как произвести установку (например игры) на карте памяти, чтоб данные не перенести на основную память.