Bedienungsanleitung Pelco MC3651H-2

12 Seiten 0.12 mb
Download

Zur Seite of 12

Summary
  • Pelco MC3651H-2 - page 1

    ® Installation/Operation MC3651H-2 Series DSP Monochr ome Camera C1985M-E (4/03) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150 International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120 ...

  • Pelco MC3651H-2 - page 2

    [ 2 ] Pelco Manual C1985M-E (4/03) Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installation personnel. 2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approve ...

  • Pelco MC3651H-2 - page 3

    Pelco Manual C1985M-E (4/03) [ 3 ] CAMERA LA YOUT Figure 1. Camera Layout INST ALLA TION Lens Mounting The camera can use a fixed iris, manual iris, or auto iris. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens. 1. C-Mount Lens Only - Rotate the back focus adjustment fully counterclockwise before install- in ...

  • Pelco MC3651H-2 - page 4

    [ 4 ] Pelco Manual C1985M-E (4/03) Power and Video Connections The MC3651H-2 camera is designed to operate from a 12 VDC or 24 V AC power supply . The power sup- ply connections are shown in Figure 1. The LED on the back panel of the camera indicates that power is connected. Use only a Class 2 isolated power supply . Power consumption is less than ...

  • Pelco MC3651H-2 - page 5

    Pelco Manual C1985M-E (4/03) [ 5 ] To connect the camera power and video: 1. Remove the cosmetic trim ring from the camera (refer to Figure 1). Thread cabling through the rear cover . 2. Connect the power cable to the two pin power connector on the back of the camera using the terminal block connector (provided). Refer to T able A for the recommend ...

  • Pelco MC3651H-2 - page 6

    [ 6 ] Pelco Manual C1985M-E (4/03) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video out- put level of 1V peak-to-peak). Switch the AGC ...

  • Pelco MC3651H-2 - page 7

    Pelco Manual C1985M-E (4/03) [ 7 ] Figure 5. Back Focus Adjustment BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring until the object is in focus. ...

  • Pelco MC3651H-2 - page 8

    [ 8 ] Pelco Manual C1985M-E (4/03) Figure 6. Default Settings OFF OFF OFF OFF AIV INT NOR OFF OFF OFF BLC AGC OPT ESC AID LL SHP LC DS1 DS2 ON PHASE LEVEL + - H L 1 2 3 4 5 6 7 8 9 10 00026 1 BLC - Back Light Compensation OFF (Default setting) - Disables the BLC mode. BLC - Enables the BLC mode. If a bright backlight is present the subjects in the ...

  • Pelco MC3651H-2 - page 9

    Pelco Manual C1985M-E (4/03) [ 9 ] 7 NOR/SHP - Sharpness NOR (Default setting) - Sets the camera to normal sharpness mode. SHP - Enables the Sharpness mode. Enhances picture detail by increasing the aperture gain of the camera, sharpening the edges in the picture. 8 LC - Long Line Compensation OFF (Default setting) - Disables the Long Line Compensa ...

  • Pelco MC3651H-2 - page 10

    [ 10 ] Pelco Manual C1985M-E (4/03) CAMERA SYNCHRONIZA TION (AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll, adjust the phase control by synchronizing, or line- locking, the cameras to one another . Use the phase pote ...

  • Pelco MC3651H-2 - page 11

    Pelco Manual C1985M-E (4/03) [ 11 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements MC3651H-2: 768 (H) x 494 (V) MC3651H-2X: 795 (H) x 596 (V) Sensing Area: 6 mm diagonally Synchronize System: INT/AC line lock Horizontal Resolution 570 TV lines Iris Control: Electronic/passive Minimum Illumination 0.0035 lux at f1.2 ...

  • Pelco MC3651H-2 - page 12

    [ 12 ] Pelco Manual C1985M-E (4/03) REVISION HISTOR Y Manual # Date Comments C1985M 10/00 Original version. C1985M-A 12/00 Added note for cosmetic trim ring. Revised switch setting illustration to depict default settings. C1985M-B 7/01 Added camera model MC3651H-2X. C1985M-C 6/02 Revised the lens connector wiring chart. C1985M-D 8/02 Revised the Di ...

Produzent Pelco Kategorie Digital Camera

Dokumente, die wir vom Produzenten des Geräts Pelco MC3651H-2 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pelco
- Bedienungsanleitungen MC3651H-2
- Produktkarten Pelco
- Informationsbroschüren
- oder Energieetiketten Pelco MC3651H-2
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pelco MC3651H-2.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pelco MC3651H-2, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pelco MC3651H-2. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pelco MC3651H-2 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pelco MC3651H-2, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pelco MC3651H-2 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pelco MC3651H-2 verständlich ist.

Eine gänzliche Bedienungsanleitung von Pelco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pelco MC3651H-2 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pelco MC3651H-2 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pelco MC3651H-2, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pelco MC3651H-2 - die uns die ersten Schritte während der Nutzung von Pelco MC3651H-2 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pelco MC3651H-2 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pelco MC3651H-2 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pelco MC3651H-2?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco MC3651H-2 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco MC3651H-2 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)