Bedienungsanleitung Stanley Black & Decker CT04

20 Seiten 1.02 mb
Download

Zur Seite of 20

Summary
  • Stanley Black & Decker CT04 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 58541 10-2014 V er . 4 USER MANUAL Safety , Operation and Maintenance CT04 HYDRAULIC CRIMPING T OOL ...

  • Stanley Black & Decker CT04 - page 2

    ...

  • Stanley Black & Decker CT04 - page 3

    CT04 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer . Please read the following warning. For the nearest authorized and certie ...

  • Stanley Black & Decker CT04 - page 4

    4 ► CT04 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker CT04 - page 5

    CT04 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs. ...

  • Stanley Black & Decker CT04 - page 6

    6 ► CT04 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA TOR. SEE OTHER SIDE 1. FAILURE TO USE H ...

  • Stanley Black & Decker CT04 - page 7

    CT04 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker CT04 - page 8

    8 ► CT04 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS 4-6 1 ...

  • Stanley Black & Decker CT04 - page 9

    CT04 User Manual ◄ 9 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity ...

  • Stanley Black & Decker CT04 - page 10

    10 ► CT04 User Manual 2. Loosen the 2 setscrews on the cylinder . 3. Turn the adapter until it stops: • Counter Clockwise (CCW) to change to closed center (creates gap) • Clockwise (CW) to change to open center (clos - es gap) 4. Tighten the two setscrews. DIE INST ALLA TION Each crimping head has two die holders: one station- ary and one mov ...

  • Stanley Black & Decker CT04 - page 11

    CT04 User Manual ◄ 1 1 • If the die load has been veried, select a set of dies to match the sleeve or connector to be crimped. TO INST ALL DIES ON KEARNEY “O” STYLE HEAD 1. Loosen the two die retainer screws (items ___ on the parts illustration). 2. Insert and center the dies. 3. Tighten the die retainer screws to lock the dies in place. ...

  • Stanley Black & Decker CT04 - page 12

    12 ► CT04 User Manual The hydraulic uid temperature should be at least 80 °F/27 °C for this test. CONNECT HOSES 1. Wipe all hose couplers with a clean, lint-free cloth before making connections. 2. Connect hoses from the hydraulic power source to the tool ttings or quick disconnects. It is good prac - tice to connect the return hose rs ...

  • Stanley Black & Decker CT04 - page 13

    CT04 User Manual ◄ 13 SHUTDOWN 1. Move the hydraulic system control valve to the OFF position. 2. Disconnect the hydraulic hoses from the tool - rst the input (supply) hose, then the output (return) hose. 3. Insert plugs in the hose ends, couplers or tool ports, as applicable. 4. Wipe the tool thoroughly with a clean dry cloth. 5. Clean any fo ...

  • Stanley Black & Decker CT04 - page 14

    14 ► CT04 User Manual NO TICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau - lic tools. Failure to do s ...

  • Stanley Black & Decker CT04 - page 15

    CT04 User Manual ◄ 15 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the grinder , always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the grinder as listed in the table. Use a owmeter known to b ...

  • Stanley Black & Decker CT04 - page 16

    16 ► CT04 User Manual Capacity ........................................................................................................................................ #6 - 4/0 Conductor Crimping Force .......................................................................................... 4.4 tons @ 1650 psi / 4000 kg @ 1 14 bar Pressure Range ...

  • Stanley Black & Decker CT04 - page 17

    CT04 User Manual ◄ 17 CT04 ILLUSTRA TION ...

  • Stanley Black & Decker CT04 - page 18

    18 ► CT04 User Manual ITEM NO. P ART NO. QTY DESCRIPTION 1 001 18 1 RET AINING RING 2 00144 12 HSHCS 3 07626 2 O-RING ■ 4 09330 1 O-RING ■ 5 00294 1 O-RING ■ 6 00360 1 O-RING ■ 7 00831 1 ROD WIPER■ 8 00936 1 ADAPTER 9 01259 1 O-RING ■ 10 01534 1 ROLL PIN 11 01608 4 STEEL BALL 12 01809 1 V AL VE SPOOL 13 01812 1 V AL VE SPOOL SCREW 14 ...

  • Stanley Black & Decker CT04 - page 19

    ...

  • Stanley Black & Decker CT04 - page 20

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 503-659-5660 / Fax 503-652-1780 www .stanleyhydraulics.com ...

Produzent Stanley Black & Decker Kategorie Crib Toy

Dokumente, die wir vom Produzenten des Geräts Stanley Black & Decker CT04 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Stanley Black & Decker
- Bedienungsanleitungen CT04
- Produktkarten Stanley Black & Decker
- Informationsbroschüren
- oder Energieetiketten Stanley Black & Decker CT04
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Stanley Black & Decker CT04.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Stanley Black & Decker CT04, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Stanley Black & Decker CT04. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Stanley Black & Decker CT04 ansehen.

Die komplette Bedienungsanleitung des Geräts Stanley Black & Decker CT04, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Stanley Black & Decker CT04 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Stanley Black & Decker CT04 verständlich ist.

Eine gänzliche Bedienungsanleitung von Stanley Black & Decker sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Stanley Black & Decker CT04 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Stanley Black & Decker CT04 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Stanley Black & Decker CT04, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Stanley Black & Decker CT04 - die uns die ersten Schritte während der Nutzung von Stanley Black & Decker CT04 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Stanley Black & Decker CT04 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Stanley Black & Decker CT04 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Stanley Black & Decker CT04?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Stanley Black & Decker CT04 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Stanley Black & Decker CT04 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)