Deutsch dropdown-ico

Bedienungsanleitung Weider 831.153930f

35 Seiten 4.54 mb
Download

Zur Seite of 35

Summary
  • Weider 831.153930f - page 1

    USER'S MANUAL Visit our website at www .weiderfitness.com new products, prizes, fitness tips, and much more! Patent Pending CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. 831.153930 Serial No. Write the serial number in the space above for reference. ...

  • Weider 831.153930f - page 2

    2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBL Y . . . . . . . . . . . ...

  • Weider 831.153930f - page 3

    IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only . Do not use the weight system in ...

  • Weider 831.153930f - page 4

    4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 77 in. Width: 81 in. Length: 59 in. Squat Knee Rest Curl Pad Low Pulley Station High Pulley Station Lat Bar Swivel Carriage Adjustment Knob Butterfly Arm/Press Arm Leg Lever Seat Squat Arm Weight Stack Backrest Backrest W ARNING DECAL 1 W ARNING DECAL 2 (one on each side) W ARNING DECAL 2 Thank you f ...

  • Weider 831.153930f - page 5

    5 ASSEMBL Y Make sure that you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and masking tape. Note: Assembly will be more convenient if you have a socket set, a set of open-end ...

  • Weider 831.153930f - page 6

    1. Locate and open the parts bags labeled “FRAME ASSEMBL Y 1” and “FRAME ASSEMBL Y 2.” Press a 2” Square Inner Cap (105) into the open end of the Long Base (120). Insert eight 5/16” x 2 1/2” Carriage Bolts (1 10) up through the Long Base (120) and the Short Base (2) as shown. Note: It may be helpful to place tape over the heads of the ...

  • Weider 831.153930f - page 7

    4. Press a 1 1/2” Square Inner Cap (67) into the square tube on the Butterfly Upright (3). Slide the Butterfly Upright (3) onto the two indicated 5/16” x 2 1/2” Carriage Bolts (1 10) in the Short Base (2). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. 5. Press a 2” x 3” Inner C ...

  • Weider 831.153930f - page 8

    8 7. Press a 2” x 3” Inner Cap (58) into the top of the Squat Upright (4). Slide the Squat Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (1 10) in the Long Base (120). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt. Do not tight- en the Nylon Locknuts yet. Press a 2” x 3” Inner Cap (58) into the top o ...

  • Weider 831.153930f - page 9

    9 9. Attach a Roller (39) and two 5/16” W ashers (90) between the indicated set of holes in the Squat Slider (38) with a 5/16” x 3 1/2” Bolt (94), two 5/16” W ashers (90), and a 5/16” Nylon Locknut (86) as shown. Assemble the other three Rollers (39) to the Squat Slider (38) in the same manner . 10. Slide the Squat Slider (38) down onto t ...

  • Weider 831.153930f - page 10

    10 14. Open the parts bag labeled “ARM ASSEMBL Y .” Press three 1 1/2” x 2” Inner Caps (21) into the Leg Lever (10). Attach the Eyebolt (1 16) to the Leg Lever with a 3/8” W asher (91) and a 3/8” Nylon Jamnut (1 13). Lubricate a 3/8” x 2 1/2” Bolt (18) with grease. T urn the Leg Lever (10) so that the welded tab is on the indicated ...

  • Weider 831.153930f - page 11

    18. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Lubricate the 3/8” x 7” Bolt (30) with grease. Attach the Swivel Cage (76) to the Swivel Carriage (46) with the Bolt and a 3/8” Nylon Locknut (87). Locate the Swivel High Cable (74), which is 126 1/2” long and has a ball on one end and a threaded bolt on the ...

  • Weider 831.153930f - page 12

    12 20. Remove the preattached 3 1/2” Pulleys (78) from the Small Pulley Plates (31). Wrap the Swivel High Cable (74) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap (68) to the second set of holes from the top of the Small Pulley Plates (31) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure the Cable T ra ...

  • Weider 831.153930f - page 13

    13 24. Remove the preattached 3 1/2” Pulleys (78) from the Offset Double “U”-bracket (61). Wrap the Swivel Cable (17) around a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”- bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 25. Wrap the Swivel Cable (17) around a 3 1/2” Pulley (78). Atta ...

  • Weider 831.153930f - page 14

    14 29. Wrap the Lat Cable (88) around a 3 1/2” Pulley (78). Attach the Pulley and a Long Cable T rap (102) to the T op Frame (6) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Jamnut (1 13). Make sure the Cable T rap is turned to hold the Cable in the groove of the Pulley . 33. Wrap the Butterfly Cable (69) over a “V”-pulley (55). Atta ...

  • Weider 831.153930f - page 15

    15 35 36 38 37 34. Remove the preattached 3 1/2” Pulleys (78) from the Double “U”-bracket (62). Wrap the Butterfly Cable (69) under a 3 1/2” Pulley (78). Attach the Pulley to the Double “U”-bracket (62) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 35. Wrap the Butterfly Cable (69) over a “V”-pulley (55). Attac ...

  • Weider 831.153930f - page 16

    16 41. Remove the preattached 3 1/2” Pulley (not shown) from the “U”-bracket (64). Attach the end of the Leg Lever Cable (75) to the “U”-bracket (64) with a 1/4” W asher (97) and a 1/4” Nylon Locknut (34). Note: Do not completely tighten the Locknut; it should be threaded only two turns onto the end of the Cable. 42. Locate the Swivel ...

  • Weider 831.153930f - page 17

    17 45. Wrap the Swivel Low Cable (72) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 46. Route the Swivel Low Cable (72) under the indicat- ed stack of Weights (44). Wrap the Swivel Low Cable (72) under a 3 1/2” Pulley (78). Atta ...

  • Weider 831.153930f - page 18

    18 49. Wrap the Swivel Low Cable (72) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley . 51. Locate the Squat Cable (7 ...

  • Weider 831.153930f - page 19

    19 53. Wrap the Squat Cable (73) under a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap to the sec- ond set of holes from the top in the indicated brack- et on the Long Base (120) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley . 54. W ...

  • Weider 831.153930f - page 20

    20 57. Attach the Seat (16) to the Seat Frame (8) with two 1/4” x 3/4” Screws (1 14), a 1/4” x 2 1/2” Screw (99), and a 1/4” W asher (97). 58. Attach the Butterfly Backrest (15) to the Butterfly Upright (3) with four 1/4” x 3/4” Screws (1 14). 59. Wet one end of the Squat Arm (32) with soapy water . Slide a Short Pad (20) onto the Squ ...

  • Weider 831.153930f - page 21

    21 61 61. Unscrew the Adjustment Knob (1 15) and remove it from the Squat Bracket (37). T urn the Squat Backrest (35) so that the four screw holes are clos- er to the bottom of the Squat Backrest than the top. Attach the Squat Backrest to the Squat Bracket with four 1/4” x 3/4” Screws (1 14). Reattach the Adjustment Knob to the Squat Bracket. T ...

  • Weider 831.153930f - page 22

    22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises. IMPOR- T AN T : When attaching the lat bar , row bar , or handle, make sure that the attachments are in the correct starting posi ...

  • Weider 831.153930f - page 23

    23 ADJUSTING THE SQUA T ARM OR SWIVEL CARRIAGE T o adjust the height of the Squat Arm (32), first turn the Adjustment Knob (1 15) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position. Engage the Handle into one of the holes in the Squat Slider (no ...

  • Weider 831.153930f - page 24

    HIGH PULLEY (lbs.) 14 25 38 48 61 68 80 96 101 11 2 122 LOW PULLEY (lbs.) 14 25 36 44 60 70 80 91 104 111 122 LEG LEVER (lbs.) 22 35 53 67 91 111 122 148 160 184 190 BUTTERFL Y ARM (lbs.) 17 26 36 45 54 63 71 80 91 100 108 PRESS ARM (lbs.) 24 39 55 70 89 104 11 8 136 154 167 187 SQUA T ST A TION (lbs.) 59 87 11 6 136 170 192 203 223 239 254 270 SWI ...

  • Weider 831.153930f - page 25

    25 TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when ...

  • Weider 831.153930f - page 26

    26 CABLE DIAGRAMS The cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia- grams on this page and the following page show the proper routing of the cables. The numbers in the diagrams show the routes of the cables. Use the diagrams to make sure that the cables have been assembled correctly . IM ...

  • Weider 831.153930f - page 27

    27 Leg Lever Cable (75) Swivel Low Cable (72) 1 1 3 2 4 5 6 7 9 2 3 4 1 2 3 4 5 8 Swivel Cable (17) ...

  • Weider 831.153930f - page 28

    Part No. 190959 R1 102A Printed in Canada © 2002 Sears, Roebuck and Co. FULL 90 DA Y W ARRANTY For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this SEARS WEIGHT SYSTEM EXERCISER, contact the nearest SEARS Service Center throughout the United States and SEARS will repair or replace the WEIGHT SYS ...

  • Weider 831.153930f - page 29

    Note: Assembly is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , and 4) seat assembly . The hardware for each stage is packaged in separate bags. W AIT UNTIL YOU BEGIN EACH ASSEMBL Y ST AGE TO OPEN THE P ARTS BAG LABELED FOR THA T ASSEMBL Y ST AGE. This chart is provided to help you identify the small parts used ...

  • Weider 831.153930f - page 30

    1" Round Inner Cap (29) 1 1/2" x 2” Inner Cap (21) 2" Square Inner Cap (105) 1 1/2" Square Inner Cap (67) 2" x 3” Inner Cap (58) 2" x 2 1/2” Inner Cap (125) ...

  • Weider 831.153930f - page 31

    Cable Clip (83) 3 1/2" Pulley (78) (Not shown to scale) "V" Pulley (55) (Not shown to scale) 4 1/2" Pulley (1 19) (Not shown to scale) 3/8" x 3 3/4" Bolt (122) 3/8" x 6 1/2" Bolt (95) 5/16" W asher (90) 5/16" x 3 3/4" Bolt (92) 5/16" x 3 1/2" Bolt (94) 1/2" Nut (1 18) 3/8" N ...

  • Weider 831.153930f - page 32

    3/8" x 2" Bolt (100) 3/8" x 1 3/4" Bolt (93) 3/8" x 1" Bolt (13) #10 x 1" Screw (14) 3/8" x 2 1/2" Bolt (18) 5/16" x 2 3/4" Bolt (85) 3/8" x 2 3/4" Bolt (101) 3/8" x 3" Bolt (107) 3/8" x 3 1/4" Bolt (96) 5/16" x 3/4" Button Head Screw (51) 5/16" x 2 ...

  • Weider 831.153930f - page 33

    81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE ...

  • Weider 831.153930f - page 34

    P ART LIST—Model No. 831.153930 R1 102A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 1/2” W asher 2 1 Short Base 3 1 Butterfly Upright 4 1 Squat Upright 5 1 Swivel Upright 6 1 T op Frame 7 1 Butterfly T op Frame 8 1 Seat Frame 9 1 Seat Upright 10 1 Leg Lever 1 1 1 Curl Pad 12 1 Curl Po ...

  • Weider 831.153930f - page 35

    4 6 5 7 3 2 8 9 10 12 16 109 109 19 19 20 20 21 21 20 11 6 21 23 24 25 26 27 27 28 29 29 28 32 33 33 111 111 35 37 38 39 39 40 40 40 42 42 43 43 47 45 44 45 44 48 48 49 50 50 11 4 11 4 52 52 55 55 56 57 57 57 58 54 54 21 60 60 64 11 5 67 68 102 69 69 70 70 72 72 73 74 17 75 75 78 11 9 78 78 78 78 78 102 102 78 79 36 36 36 80 81 82 83 78 11 9 11 9 7 ...

Produzent Weider Kategorie Home Gym

Dokumente, die wir vom Produzenten des Geräts Weider 831.153930f erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Weider
- Bedienungsanleitungen 831.153930f
- Produktkarten Weider
- Informationsbroschüren
- oder Energieetiketten Weider 831.153930f
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Weider 831.153930f.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Weider 831.153930f, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Weider 831.153930f. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Weider 831.153930f ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Weider 831.153930f, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Weider 831.153930f hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Weider 831.153930f verständlich ist.

Eine gänzliche Bedienungsanleitung von Weider sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Weider 831.153930f bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Weider 831.153930f befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Weider 831.153930f, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Weider 831.153930f - die uns die ersten Schritte während der Nutzung von Weider 831.153930f erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Weider 831.153930f hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Weider 831.153930f im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Weider 831.153930f?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Weider 831.153930f nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Weider 831.153930f hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)