Bedienungsanleitung Honeywell RTH2310

24 Seiten 1.24 mb
Download

Zur Seite of 24

Summary
  • Honeywell RTH2310 - page 1

    69-2214EF-02 Quick Inst allation Guide RTH2310 Programmable Thermostat ...

  • Honeywell RTH2310 - page 2

    Quick Installa tion Guide 1 Installation is Easy Y our new thermostat has been designe d for fast an d easy installation. Just follo w the simple step-by-step instructions in the following pages.  Identify your system type.  Remove your old thermostat.  Identify the wires.  Mount the new wallplate.  Connect the wires.  If the wire ...

  • Honeywell RTH2310 - page 3

    RTH2310 Programmable Thermostat 2 This thermostat is compatible wi th the following systems: • Gas, oil or electric furnace • Central air condition er • a hot water system with or without pump • a millivolt system • a central heating and cooling system If you are not sure of your system type or if you have any other questio ns, call us to ...

  • Honeywell RTH2310 - page 4

    Quick Installa tion Guide 3 1) T urn power off at the h eating/cooling system. 2) Remove old thermostat, but leave wallplate with wires attached. MERCUR Y NOTICE : Do not put your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority for instructions regarding recycling and proper disposa ...

  • Honeywell RTH2310 - page 5

    RTH2310 Programmable Thermostat 4 If any wires are not attached to your old thermostat or are attached to a terminal marked C or C1 , they will not be connected to your new thermostat. Wrap the bare met al end of each of these wires with elec trical tape, so it cannot touch and short other wires. Disconnect wires and remov e the old wallpla te only ...

  • Honeywell RTH2310 - page 6

    Quick Installa tion Guide 5 1) Remove coverplate. 2) Loosen screw (the screw remains captive on wallplate). 3) Remove thermostat. 4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.  Mount New W allplate 4. ...

  • Honeywell RTH2310 - page 7

    RTH2310 Programmable Thermostat 6 1) Match each labeled wire with the terminal having the same letter . 2) Loosen the terminal screws using a screwdriver , insert the wires, then tighten the screws. 3) Push any excess wire back into the wall opening.  Connect Wires (typical wiring) 5. Remove jumper if you have both R and Rc wires. Labels don’t ...

  • Honeywell RTH2310 - page 8

    Quick Installa tion Guide 7 If a labeled wire does n ot match any terminal designation, see diagram below . Do not use C, X or B. Wrap bare end o f wire with electrical tape. If wires are connected to both Rh and Rc terminals, remove jumper (se e previous page).  Connect Wires (less common wiring) ...

  • Honeywell RTH2310 - page 9

    RTH2310 Programmable Thermostat 8 Set the Jumper J2, o n the back of the thermost at, if you have connected a wire to the G terminal .  Specify Furnace T ype 6. HG Leave the jumper in this factor y-set position if you ha ve a gas or oil furnace. HE Place the jumper to this position if yo u have an electric furnace. J2 jumper ...

  • Honeywell RTH2310 - page 10

    Quick Installa tion Guide 9 1) Pull out the battery cover . 2) Install the batteries as shown. Observe the polarity . 3) Reinstall the battery cover . Y ou will hea r a clicking sound. After the batteries are inst alled, the thermostat per- forms a series of tests for approximately 5 seconds. Afterwards, the screen displays the actual te mpera- tur ...

  • Honeywell RTH2310 - page 11

    RTH2310 Programmable Thermostat 10 1) Mount the thermostat on the wallplate. 2) T ighten the screw and install the coverplate. 3) T urn power back o n at the heating/cooling system.  Install thermostat 8. ...

  • Honeywell RTH2310 - page 12

    Quick Installa tion Guide 11 1) Press both and buttons simultaneously for 3 seconds to enter or exit the setup menu. 2) T o a dvance to the next function, briefly press both and bu ttons simultaneously . 3) T o chang e the setting, press the or button.  System Setup 9. DISPLA Y DESCRIPTION OPTIONS 1 T emperature display °C or °F Time display 1 ...

  • Honeywell RTH2310 - page 13

    Guide d’inst allation rapide RTH2310 Thermostat programmable 69-2214EF-02 69-2214F_A.fm Page 0 Frida y, February 19, 2010 8:35 AM ...

  • Honeywell RTH2310 - page 14

    Guide d’installa tion rapide 1 Installation facile V otre nouveau thermostat est conçu pour u n montage rapide et facile. Suivez les explications simples fournies dans les pages suivantes.  Identifier votre type de système.  Enlever l’ancien thermostat.  Identifier les fils.  Installer la nouvelle plaque murale.  Brancher les f ...

  • Honeywell RTH2310 - page 15

    Thermostat programmable R TH2310 2 Ce thermostat est comp atible avec les systèmes suivants : • fournaise électrique, au gaz ou au mazout • climatiseur central • système de chauffage à eau ch aude avec ou sans pompe • système millivolt • système de chauffage et de climatisation central Si vous n’êtes p as certain quel typ e de sy ...

  • Honeywell RTH2310 - page 16

    Guide d’installa tion rapide 3 1) Mettre le système de chauffage /climatisation hors tension. 2) Enlever l’ancien thermostat, mais pas la plaque murale et les fils qui y sont reliés. A VIS SUR LE MERCURE : Ne pas jeter votre ancien thermostat aux ordures s’il contient une ampoule de mercure. Communiquer avec le service de gestion des déche ...

  • Honeywell RTH2310 - page 17

    Thermostat programmable R TH2310 4 Si des fils ne sont p as branchés aux bornes de l’ancien thermostat ou sont branchés à une b orne marquée C ou C1 , ils ne seront pas branchés au nouveau thermos tat. Recouvrir le bout dénudé de chaque fil non utilisé de ruban isolant, pour éviter qu’ils se touchent et causent des court-circuit s avec ...

  • Honeywell RTH2310 - page 18

    Guide d’installa tion rapide 5 1) Retirer le couvercle. 2) Dévisser la vis de fixation (elle reste captive sur la plaque murale). 3) Retirer le thermostat. 4) Marquer et percer des trous de fixation (ou utiliser les trous existant). Insérer les chevilles d'ancrage. Passer les fils par l'ouverture de la plaque murale et fixer la plaque ...

  • Honeywell RTH2310 - page 19

    Thermostat programmable R TH2310 6 1) Associer chaque fil étique té à la borne ayant la même lettre. 2) Dévisser les vis des bornes avec un tournevis, insérer les fils et resserrer les vis. 3) Repousser les fils en trop dans le mur .  Branchement (typique) 5. Enlever le cavalier si vous avez les fils R e t Rc. Les étiquettes ne correspond ...

  • Honeywell RTH2310 - page 20

    Guide d’installa tion rapide 7 Si un fil étiqueté ne correspon d pas à aucune borne, voir le diagramme ci-dessous. Ne pas utiliser C, X ou B. Enrouler le bout dénudé du fil avec du ruban isolant. Si des fils sont reliés aux bornes Rh et Rc, enlever le cavalie r (voir la page précéden te).  Branchement (moins commun) 69-2214F_A.fm Page ...

  • Honeywell RTH2310 - page 21

    Thermostat programmable R TH2310 8 La position du cavalier J2, à l'endos du thermostat, est important si vous avez branché u n fil à la borne G .  Préciser le type de fournaise 6. HG Laisser le cavalier dans cette position si vous avez une fournais e à gaz ou au mazout . HE Placer le cavalier dans cette position si vous avez une fourna ...

  • Honeywell RTH2310 - page 22

    Guide d’installa tion rapide 9 1) Retirer le couvercle du compartiment à piles. 2) Installer les piles tel qu'illustré. Observer la polarité. 3) Remettre le couvercle en place. Un d éclic se fera entendre. Une fois les piles installées, le thermo stat ef fectue une série de tests, qui dure enviro n 5 secondes. Par la suite, l'écr ...

  • Honeywell RTH2310 - page 23

    Thermostat programmable R TH2310 10 1) Placer le thermostat sur la plaque murale. 2) Serrer la vis et placer le couvercle. 3) Mettre le système de chauffage/climatisation sous tension.  Installer le thermostat 8. 69-2214F_A.fm Page 10 Friday, February 19, 2010 8:35 AM ...

  • Honeywell RTH2310 - page 24

    Guide d’installa tion rapide 11 1) Appuyer simultanémen t sur les boutons et buttons pendant 3 secondes pour entr er dans le menu ou en sortir . 2) Pour passer à la fonct ion suivante, appuyer simultanément et brièvement sur les boutons et . 3) Pour modifier le réglage, app uyer sur le bouton ou .  Réglage du système 9. AFFICHAGE DESCRI ...

Produzent Honeywell Kategorie Thermostat

Dokumente, die wir vom Produzenten des Geräts Honeywell RTH2310 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Honeywell
- Bedienungsanleitungen RTH2310
- Produktkarten Honeywell
- Informationsbroschüren
- oder Energieetiketten Honeywell RTH2310
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Honeywell RTH2310.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Honeywell RTH2310, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Honeywell RTH2310. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Honeywell RTH2310 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Honeywell RTH2310, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Honeywell RTH2310 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Honeywell RTH2310 verständlich ist.

Eine gänzliche Bedienungsanleitung von Honeywell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Honeywell RTH2310 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Honeywell RTH2310 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Honeywell RTH2310, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Honeywell RTH2310 - die uns die ersten Schritte während der Nutzung von Honeywell RTH2310 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Honeywell RTH2310 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Honeywell RTH2310 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Honeywell RTH2310?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Honeywell RTH2310 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Honeywell RTH2310 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)