Bedienungsanleitung Apple Power Mac 073-0841

16 Seiten 0.5 mb
Download

Zur Seite of 16

Summary
  • Apple Power Mac 073-0841 - page 1

    073-0841 Re v . A  Power Mac G4 Cube Optical Drive Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Written and video instructions cov ering customer-installable par ts are av ailab le at http://www .info .apple.com/inst ...

  • Apple Power Mac 073-0841 - page 2

    Power Mac G4 Cube Optical Drive - 2 Removing the Computer Cor e Fr om the Enclosur e W arning: Always shut do wn y our computer before opening it to a v oid dama ging its internal components or causing injury . After y ou shut do wn the computer , the internal components can be very hot. Let the computer cool down bef ore continuing. 1 Place your c ...

  • Apple Power Mac 073-0841 - page 3

    Power Mac G4 Cube Optical Drive - 3 6 T ur n the computer upside down, and push do wn on the latch to release it. Allow the latch to extend completely. (Figure 2) Figure 2 7 Gently pull the core from the computer enclosure and place the core on a soft cloth. (Figure 3) Figure 3 Latch Extended Latch Core Enclosure ...

  • Apple Power Mac 073-0841 - page 4

    Power Mac G4 Cube Optical Drive - 4 Removing the T op Plate Assembly 1. Press the latch in, and tur n o v er the core so the pow er button f aces up . 2. Remov e the f our corner screws that secure the top plate to the f our v er tical posts . 3. Remov e the f our scre ws on the two sides . (The two scre ws that align with the v er tical plates are ...

  • Apple Power Mac 073-0841 - page 5

    Power Mac G4 Cube Optical Drive - 5 4. Lift out the LED cov er that is fitted o v er the pow er button LED . Set the LED co v er aside f or installation on the top plate assemb ly . (Figure 5) Figure 5 5. Carefully lift up the top plate and disconnect the ke y ed connector (J1 on the logic board). (Figure 6) Figure 6 ...

  • Apple Power Mac 073-0841 - page 6

    Power Mac G4 Cube Optical Drive - 6 Removing the Installed Optical Dri ve Note: The procedure is the same whether the optical dr iv e is a CD-R W or a D VD-ROM drive . 1. Grasp the top of the side panel, and slide it up and a wa y to clear the f our tabs on the inner side of the panel. (Figure 7) Figure 7 2. Mov e the AirP or t Card antenna cable o ...

  • Apple Power Mac 073-0841 - page 7

    Power Mac G4 Cube Optical Drive - 7 3. Using a magnetized scre wdriver , remov e the two scre ws from the side of the drive . Repeat on the other side. (Figure 9) Figure 9 ...

  • Apple Power Mac 073-0841 - page 8

    Power Mac G4 Cube Optical Drive - 8 4. W arning: If the optical drive case is squeezed too tightly, the laser lens could be damaged. When handling the drive case, touch only the outer edges of the case. Holding the drive case by the corner, pull the drive up about half way and disconnect the ATA ribbon cable. Then, using pliers, grasp the power cab ...

  • Apple Power Mac 073-0841 - page 9

    Power Mac G4 Cube Optical Drive - 9 6. Disconnect the board from the drive b y removing the tw o screws . Then pull the board off of the drive . (Figure 11) W arning: If the optical drive case is squeezed too tightly, the laser lens could be damaged. When handling the drive case, touch only the outer edges of the case. Figure 11 Installing the Repl ...

  • Apple Power Mac 073-0841 - page 10

    Power Mac G4 Cube Optical Drive - 10 2. Install the connector board on the replacement optical drive , and secure it to the driv e with the two scre ws. (Figure 13) Figure 13 3. Holding the optical drive case b y one corner , position the drive o v er the chassis so the labeled panel f aces out and the connector board is at the bottom of the drive ...

  • Apple Power Mac 073-0841 - page 11

    Power Mac G4 Cube Optical Drive - 11 5. Install the screws , b ut do not tighten until all f our are in place. Do not ov ertighten. 6. Close the AirP or t Card door and secure the antenna cable (and AirP or t Card). 7. Star ting with the two bottom tabs , attach the side panel as shown. Ensure all f our tabs engage and no cables get caught. (Figure ...

  • Apple Power Mac 073-0841 - page 12

    Power Mac G4 Cube Optical Drive - 12 Replacing the T op Plate Assembly 1. With the top plate assembly in hand, connect the cab le from the top plate to the J1 connector on the logic board. (Figure 17) W arning: To prevent damage to the power board, ensure the keyed connector fits into the J1 connector as shown. Figure 17 ...

  • Apple Power Mac 073-0841 - page 13

    Power Mac G4 Cube Optical Drive - 13 2. Install the LED cov er o v er the pow er button LED on the top plate assemb ly . 3. P osition the top plate assembly ov er the core . Ensure that the four metal tabs align with the f our slots in the top plate, and the D VD-ROM panel tuc ks in under the lip of the top plate. (Figure 18) Figure 18 4. Star ting ...

  • Apple Power Mac 073-0841 - page 14

    Power Mac G4 Cube Optical Drive - 14 Replacing the Computer Cor e in the Enclosur e 1. Make sure that the po wer b utton gask et is secured inside the recessed area of the computer enclosure. (Figure 19) Figure 19 Caution: If the power button gasket is not centered correctly in the shell, the computer might not power up. Make sure the power button ...

  • Apple Power Mac 073-0841 - page 15

    Power Mac G4 Cube Optical Drive - 15 2 Holding the core by the latch, insert the core into the enclosure. (Figure 20) Note: The core fits into the enclosure only one way. Position the core so the ports are toward the back of the enclosure. Figure 20 3 With a flat hand, press down on the latch until it loc ks into place . Fir mly press the core to ...

  • Apple Power Mac 073-0841 - page 16

    Power Mac G4 Cube Optical Drive - 16 4 T ur n y our computer upright and reconnect all cables. 5 Restar t your computer . W arning: Never turn on your computer unless all of its internal and e xternal parts are in place and it is closed. Operating the computer when it is open or missing parts can damage your computer or cause injury .  Apple Com ...

Produzent Apple Kategorie Personal Computer

Dokumente, die wir vom Produzenten des Geräts Apple Power Mac 073-0841 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Apple
- Bedienungsanleitungen Power Mac 073-0841
- Produktkarten Apple
- Informationsbroschüren
- oder Energieetiketten Apple Power Mac 073-0841
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Apple Power Mac 073-0841.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Apple Power Mac 073-0841, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Apple Power Mac 073-0841. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Apple Power Mac 073-0841 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Apple Power Mac 073-0841, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Apple Power Mac 073-0841 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Apple Power Mac 073-0841 verständlich ist.

Eine gänzliche Bedienungsanleitung von Apple sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Apple Power Mac 073-0841 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Apple Power Mac 073-0841 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Apple Power Mac 073-0841, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Apple Power Mac 073-0841 - die uns die ersten Schritte während der Nutzung von Apple Power Mac 073-0841 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Apple Power Mac 073-0841 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Apple Power Mac 073-0841 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Apple Power Mac 073-0841?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Apple Power Mac 073-0841 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Apple Power Mac 073-0841 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)