Bedienungsanleitung Dell W03C

101 Seiten 8.13 mb
Download

Zur Seite of 101

Summary
  • Dell W03C - page 1

    Dell Vostro 360 Owner's Manual Regulatory Model W03C Regulatory Type W03C001 ...

  • Dell W03C - page 2

    Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Information in this publicati ...

  • Dell W03C - page 3

    Contents Notes, Cautions, and Warnings ..................................................................2 1 Working on Your Computer ......................................................................7 Before Working Inside Your Computer .............................................................................7 Recommended Tools ........... ...

  • Dell W03C - page 4

    9 Removing The Hard Drive Assembly ..................................................... 29 Installing The Hard Drive ................................................................................................. 31 10 Removing The Input/Output Panel ....................................................... 33 Installing The Input/Output Panel ... ...

  • Dell W03C - page 5

    21 Removing The Heatsink ......................................................................... 57 Installing The CPU Heatsink ............................................................................................ 58 22 Removing The Processor ...................................................................... 59 Installing The Processor ...

  • Dell W03C - page 6

    System Setup Options ..................................................................................................... 87 32 Diagnostic Error Messages .................................................................. 91 Diagnostic Beep Codes ................................................................................................... 92 ...

  • Dell W03C - page 7

    1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that ...

  • Dell W03C - page 8

    NOTE: The color of your computer and certain components may appear differently than shown in this document. To avoid damaging your computer, perform the following steps before you begin working inside the computer. 1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched. 2. Turn off your computer (see T ...

  • Dell W03C - page 9

    Click Start , then click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down . • In Windows XP: Click Start → Turn Off Computer → Turn Off . The computer turns off after the operating system shutdown process is complete. 2. Ensure that the computer and all attached devices are turned off. If your com ...

  • Dell W03C - page 10

    10 ...

  • Dell W03C - page 11

    2 Removing The Rear Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the screws that secure the rear cover. 3. Pry the cover away from the computer. 4. Lift the cover away from the computer. 11 ...

  • Dell W03C - page 12

    Installing The Rear Cover 1. Place the rear cover on the chassis. 2. Press down on the rear cover, until it clicks into place. 3. Replace the screws to secure the rear cover to the computer. 4. Follow the procedures in After Working Inside Your Computer 12 ...

  • Dell W03C - page 13

    3 Removing The Rear Stand 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the screws that secure the rear stand to the computer. 4. Pull the rear stand in an upwards direction and remove it from the chassis. 13 ...

  • Dell W03C - page 14

    Installing The Rear Stand 1. Align the rear stand into the chassis and ensure it clicks into place. 2. Tighten the screws to secure the rear stand to the computer. 3. Install the rear cover . 4. Follow the procedures in After Working Inside Your Computer 14 ...

  • Dell W03C - page 15

    4 Removing The Front Feet 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the screws that secure the left front foot. 4. Remove the left front foot. 5. Remove the screws that secure the right front foot. 15 ...

  • Dell W03C - page 16

    6. Remove the right front foot. Installing The Front Feet 1. Align the front feet to the bottom left and right of chassis. 2. Tighten the screws to secure the left and right front feet. 3. Install the rear cover . 4. Follow the procedures in After Working Inside Your Computer 16 ...

  • Dell W03C - page 17

    5 Removing The Rear Stand Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the screws that secure the top and the inside of the rear stand cover. 5. Lift up the rear stand cover and remove it from the computer. 17 ...

  • Dell W03C - page 18

    Installing The Rear Stand Cover 1. Align the rear stand cover on the chassis. 2. Tighten the screws to secure the outside and the inside of the rear stand cover. 3. Install the rear stand . 4. Install the rear cover . 5. Follow the procedures in After Working Inside Your Computer 18 ...

  • Dell W03C - page 19

    6 Removing The Rear I/O Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the screws that secure the rear I/O cover. 5. Pry the rear I/O cover loose from the chassis and lift it up. 19 ...

  • Dell W03C - page 20

    Installing The Rear Input/Output (I/O) Cover 1. Align and secure the rear I/O cover on the chassis. 2. Tighten the screws to secure the rear I/O cover in place. 3. Install the rear stand . 4. Install the rear cover . 5. Follow the procedures in After Working Inside Your Computer 20 ...

  • Dell W03C - page 21

    7 Removing The Optical Drive 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Disconnect the SATA cable from the optical drive. 4. Remove the screw that secures the optical drive to the chassis. 5. Slide the optical drive out of the computer. 21 ...

  • Dell W03C - page 22

    6. Remove the screws that secure the optical-drive holder. 7. Remove the holder from the optical-drive module . 22 ...

  • Dell W03C - page 23

    Installing The Optical Drive 1. Place the holder back on the optical drive and tighten the screw to secure the optical drive. 2. Slide the optical drive back into the computer. 3. Tighten the screw to secure the optical drive to the chassis. 4. Connect the SATA cable to the optical drive. 5. Install the rear cover . 6. Follow the procedures in Afte ...

  • Dell W03C - page 24

    24 ...

  • Dell W03C - page 25

    8 Removing The Memory Module 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Pry the memory cover and lift it up from the computer. 4. Pry the retention clips away from the memory module until it pops up. 5. Remove the memory module from its connector on the computer. 25 ...

  • Dell W03C - page 26

    6. Pry the retention clips away from the second memory module until it pops up. 7. Remove the second memory module from its connector on the computer. 26 ...

  • Dell W03C - page 27

    Installing The Memory Module 1. Insert the memory module into the memory socket. 2. Press the retention clips to secure the memory module in place. 3. Install the rear cover . 4. Follow the procedures in After Working Inside Your Computer 27 ...

  • Dell W03C - page 28

    28 ...

  • Dell W03C - page 29

    9 Removing The Hard Drive Assembly 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear I/O cover . 4. Remove the rear stand . 5. Remove the screw that secures the hard-drive bracket to the chassis. 6. Slide the hard-drive bracket towards the outside of the computer to release the tabs from ...

  • Dell W03C - page 30

    7. Disconnect the hard-drive cable from the hard drive. 8. Lift the hard-drive bracket out of the chassis. Remove the screws that secure the hard-drive cage to the hard drive. 9. Slide the hard drive out from the cage. 30 ...

  • Dell W03C - page 31

    Installing The Hard Drive 1. Slide the hard drive back into the cage. 2. Replace the screws to secure the hard drive to the hard-drive cage. 3. Slide and push the hard-drive bracket into the chassis to secure it. 4. Tighten the screw to secure the hard-drive bracket to the chassis. 5. Install the rear stand . 6. Install the rear I/O cover . 7. Inst ...

  • Dell W03C - page 32

    32 ...

  • Dell W03C - page 33

    10 Removing The Input/Output Panel 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the system board shield . 6. Remove the I/O panel away from the chassis. Installing The Input/Output Panel 1. Place the system board shield on the chassis ...

  • Dell W03C - page 34

    34 ...

  • Dell W03C - page 35

    11 Removing The System Board Shield 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the I/O panel . 6. Remove the screws that secure the system board shield. 7. Tilt the system board shield at an angle and remove it from the computer. 35 ...

  • Dell W03C - page 36

    Installing The System Board Shield 1. Place the system board shield on the chassis. 2. Tighten the screws to secure the system board shield. 3. Install the I/O panel . 4. Install the rear I/O cover . 5. Install the rear stand . 6. Install the rear cover . 7. Follow the procedures in After Working Inside Your Computer . 36 ...

  • Dell W03C - page 37

    12 Removing The WLAN Card 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the system board shield . 6. Disconnect the antenna cables from the WLAN card. 7. Remove the screw that secures the WLAN card and remove it from the computer. 37 ...

  • Dell W03C - page 38

    Installing The WLAN Card 1. Slide the WLAN card into its slot. 2. Tighten the screws to secure the WLAN card in place. 3. Connect the antenna cables according to the color code on the WLAN card. 4. Install the system board shield . 5. Install the rear I/O cover . 6. Install the rear stand . 7. Install the rear cover . 8. Follow the procedures in Af ...

  • Dell W03C - page 39

    13 Removing The Speakers 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the system board shield . 6. Disconnect the speaker cable from the system board. 7. Remove the screws that secure the right and left speakers. 39 ...

  • Dell W03C - page 40

    8. Remove the speakers from the computer. Installing The Speakers 1. Place the speakers on the chassis. 2. Tighten the screws to secure both the speakers in place. 3. Connect the speaker cable to the system board. 4. Install the system board shield . 5. Install the rear I/O cover . 6. Install the rear stand . 7. Install the rear cover . 8. Follow t ...

  • Dell W03C - page 41

    14 Removing The Middle Frame 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the front foot . 6. Remove the optical drive . 7. Remove the screws that secure the middle frame. 8. Pry the middle frame loose from the chassis. 41 ...

  • Dell W03C - page 42

    9. Remove the middle frame from the computer. Installing The Middle Frame 1. Place the middle frame on the chassis. 2. Secure the clips until all of them snap on to the chassis. 3. Tighten the screws to secure the middle frame. 4. Install the optical drive . 5. Install the front feet . 6. Install the rear I/O cover . 7. Install the rear stand . 8. ...

  • Dell W03C - page 43

    15 Removing The Touch-Control Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Disconnect the connector cables from the touch-control board. NOTE: The touch-control board and the cable are part of the display Panel assembly. 4. Remove the screws that secure the touch-control board. 43 ...

  • Dell W03C - page 44

    5. Lift the touch-control board from the chassis. Installing The Touch-Control Board 1. Place the touch-control board on the chassis. 2. Tighten the screws to secure the touch-control board. 3. Connect the connector cables into place on the touch-control board. 4. Install the rear cover . 5. Follow the procedures in After Working Inside Your Comput ...

  • Dell W03C - page 45

    16 Removing The Power-Switch Assembly 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the screw that secures the power-switch assembly to the chassis. 6. Disconnect the power-switch assembly from the system board. 45 ...

  • Dell W03C - page 46

    7. Disengage the cable from the chassis clips and remove the power-switch assembly. Installing The Power-Switch Assembly 1. Place the power-switch assembly on the chassis. 2. Connect the power-switch assembly cable to the system board and thread the cables into the chassis clips. 3. Tighten the screw that secures the power-switch assembly to the ch ...

  • Dell W03C - page 47

    17 Removing The Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the system board shield . 6. Pry the tabs that secure the coin-cell battery to the system board. 7. Remove the coin-cell battery from its socket. 47 ...

  • Dell W03C - page 48

    Installing The Coin-Cell Battery 1. Insert the coin-cell battery into the slot. 2. Install the system board shield . 3. Install the rear I/O cover . 4. Install the rear stand . 5. Install the rear cover . 6. Follow the procedures in After Working Inside Your Computer . 48 ...

  • Dell W03C - page 49

    18 Removing The Heatsink Fan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the system board shield . 6. Remove the screws that secure the fan to the chassis. 7. Disconnect the heatsink fan cable from the system board. 49 ...

  • Dell W03C - page 50

    8. Lift and remove the heatsink fan from the computer. Installing The Heatsink Fan 1. Install the heatsink fan on the chassis. 2. Tighten the screws to secure the heatsink fan to the chassis. 3. Connect the heatsink fan connector to its socket on the system board. 4. Install the system board shield . 5. Install the rear I/O cover . 6. Install the r ...

  • Dell W03C - page 51

    19 Removing The Converter Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the system board shield . 7. Disconnect the power cable from the system board. 8. Remove the white cable from the connector ...

  • Dell W03C - page 52

    9. Remove the screws that secure the converter board. 10. Lift up and remove the converter board from the computer. 52 ...

  • Dell W03C - page 53

    Installing The Converter Board 1. Install the screws to secure the converter board. 2. Insert the white cable into the connector on the converter board. 3. Install the system board shield . 4. Install the rear stand cover . 5. Install the rear I/O cover . 6. Install the rear stand . 7. Install the rear cover . 8. Follow the procedures in After Work ...

  • Dell W03C - page 54

    54 ...

  • Dell W03C - page 55

    20 Removing The CPU Fan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the system board shield . 7. Disconnect the CPU-fan cable. 8. Remove the screws that secure the CPU fan to the chassis. 55 ...

  • Dell W03C - page 56

    9. Peel the tape sealing the CPU fan to the heat sink and remove the CPU fan from the system. Installing The CPU Fan 1. Install the screws to secure the CPU fan to the chassis. 2. Secure the tape sealing the CPU fan to the heatsink. 3. Connect the CPU fan connector to the system board. 4. Install the system board shield . 5. Install the rear stand ...

  • Dell W03C - page 57

    21 Removing The Heatsink 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the system board shield . 7. Remove the CPU fan . 8. Remove the screw that secures the heatsink to the chassis, and remove the scre ...

  • Dell W03C - page 58

    Installing The CPU Heatsink 1. Place the CPU heatsink into the chassis. 2. Tighten the screws to secure the CPU heatsink to the system board, and also tighten the screw that secures the heatsink to the chassis. 3. Install the CPU fan . 4. Install the system board shield . 5. Install the rear stand cover . 6. Install the rear I/O cover . 7. Install ...

  • Dell W03C - page 59

    22 Removing The Processor 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the system board shield . 7. Remove the CPU fan . 8. Remove the CPU heatsink . 9. Press the release lever down and then move it ou ...

  • Dell W03C - page 60

    Installing The Processor 1. Insert the processor into the processor socket. Ensure the processor is properly seated. 2. Lower the processor cover. 3. Press the release lever down and then move it inward to secure it with the retention hook. 4. Install the CPU heatsink . 5. Install the CPU fan . 6. Install the system board shield . 7. Install the re ...

  • Dell W03C - page 61

    23 Removing The System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the system board shield . 7. Remove the CPU fan . 8. Remove the CPU heatsink . 9. Remove the memory module . 10. Remove the WLA ...

  • Dell W03C - page 62

    15. Lift the system board out of the chassis and remove it from the computer. Installing The System Board 1. Align the system board to the chassis and place it on the chassis. 2. Install the screws that secure the system board to the chassis. 3. Connect the cables to the system board. 4. Install the processor . 5. Install the coin-cell battery . 6. ...

  • Dell W03C - page 63

    11. Install the rear stand cover . 12. Install the rear I/O cover . 13. Install the rear stand . 14. Install the rear cover . 15. Follow the procedures in After Working Inside Your Computer . 63 ...

  • Dell W03C - page 64

    64 ...

  • Dell W03C - page 65

    24 Removing The Tempan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear stand cover . 5. Remove the rear I/O cover . 6. Remove the middle frame . 7. Remove the hard drive cage and the hard drive . 8. Remove the optical drive . 9. Remove the system board shield ...

  • Dell W03C - page 66

    19. Unthread the cables from the chassis clips. 20. Slide the tempan out from the chassis and remove it. 66 ...

  • Dell W03C - page 67

    Installing The Tempan 1. Place the tempan on the chassis. 2. Thread the cables back in their place and ensure they are secured into the chassis clips. 3. Tighten the silver and the black screws that secure the tempan to the chassis. 4. Install the touch control board . 5. Install the power switch assembly . 6. Install the converter board . 7. Insta ...

  • Dell W03C - page 68

    68 ...

  • Dell W03C - page 69

    25 Removing The Speaker Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear stand cover . 5. Remove the rear I/O cover . 6. Remove the front foot . 7. Remove the middle frame . 8. Remove the optical drive . 9. Remove the speakers . 10. Remove the screws tha ...

  • Dell W03C - page 70

    Installing The Speaker Cover 1. Place the speaker cover on the chassis. 2. Tighten the screws to secure the speaker cover to the chassis. 3. Install the speakers . 4. Install the optical drive . 5. Install the middle frame . 6. Install the front feet . 7. Install the rear I/O cover . 8. Install the rear stand . 9. Install the rear cover . 10. Follo ...

  • Dell W03C - page 71

    26 Removing The Front Bezel 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the middle frame . 7. Remove the system board shield . 8. Remove the hard drive cage and the hard drive . 9. Remove the optical ...

  • Dell W03C - page 72

    Installing The Front Bezel 1. Place the front bezel on the chassis. 2. Hold the assembly together. 3. Tighten the screws to secure the front bezel to the display panel. 4. Install the speaker cover . 5. Install the speakers . 6. Install the tempan . 7. Install the system board . 8. Install the CPU heatsink . 9. Install the CPU fan . 10. Install the ...

  • Dell W03C - page 73

    27 Removing The Low-Voltage Differential Signaling (LVDS) Cable 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the middle frame . 7. Remove the system board shield . 8. Remove the hard drive cage and the ...

  • Dell W03C - page 74

    16. Disconnect the LVDS cable from its connector and remove it from the computer. Installing The Low-Voltage Differential Signaling (LVDS) Cable 1. Connect the LVDS cable to its connector. 2. Secure the plastic tape that connects the LVDS cable to the chassis. 3. Install the tempan . 4. Install the system board . 5. Install the CPU heatsink . 6. In ...

  • Dell W03C - page 75

    10. Install the middle frame . 11. Install the rear stand cover . 12. Install the rear I/O cover . 13. Install the rear stand . 14. Install the rear cover . 15. Follow the procedures in After Working Inside Your Computer . 75 ...

  • Dell W03C - page 76

    76 ...

  • Dell W03C - page 77

    28 Removing The Display Panel NOTE: The touch-control board and the cable are a part of the Display Panel assembly. 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the middle frame . 7. Remove the system ...

  • Dell W03C - page 78

    Installing The Display Panel NOTE: While replacing the Display Panel, remove the display brackets from the old Display Panel assembly and install it on the new Display Panel Assembly. 1. Install the screws for both the railings that connect to the display panel. 2. Attach the front bezel and the LVDS cable back to the display panel. 3. Install the ...

  • Dell W03C - page 79

    29 Removing The Webcamera 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the middle frame . 7. Remove the system board shield . 8. Remove the hard drive cage and the hard drive . 9. Remove the optical dr ...

  • Dell W03C - page 80

    Installing The Webcamera 1. Place the webcamera on the chassis. 2. Tighten the screws to secure the webcamera to the chassis. 3. Connect the webcamera cable to the system board after installation. 4. Install the tempan . 5. Install the front bezel . 6. Install the speaker cover . 7. Install the speakers . 8. Install the system board . 9. Install th ...

  • Dell W03C - page 81

    30 Removing The Antenna 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the rear cover . 3. Remove the rear stand . 4. Remove the rear I/O cover . 5. Remove the rear stand cover . 6. Remove the middle frame . 7. Remove the system board shield . 8. Remove the hard drive cage and the hard drive . 9. Remove the optical driv ...

  • Dell W03C - page 82

    18. Remove the screws that secure each antenna. 19. Lift up the antennae with its cables. 82 ...

  • Dell W03C - page 83

    Installing The Antenna 1. Place both the antennae on the chassis. 2. Install the screws to secure each of the antennae. 3. Install the securing tape onto each of the antennae. 4. Route the cables into the chassis clips. 5. Install the tempan . 6. Install the speaker cover . 7. Install the speakers . 8. Install the system board . 9. Install the CPU ...

  • Dell W03C - page 84

    84 ...

  • Dell W03C - page 85

    31 System Setup Overview System Setup allows you to: • change the system configuration information after you add, change, or remove any hardware in your computer. • set or change a user-selectable option such as the user password. • read the current amount of memory or set the type of hard drive installed. Before you use System Setup, it is r ...

  • Dell W03C - page 86

    Options List — Appears on the left side of the System Setup window. The field lists features that define the configuration of your computer, including installed hardware, power conservation, and security features. Scroll up and down the list with the up- and down-arrow keys. As an option is highlighted, the Options Field displays the option' ...

  • Dell W03C - page 87

    System Setup Options Main The Main tab lists out the primary hardware features of the computer. The table below defines the function of each option. System Information Displays the computer model number. BIOS Version Displays the BIOS revision. System Date Re-sets the date on the computer's internal calendar. System Time Re-sets the time on th ...

  • Dell W03C - page 88

    Advanced The Advanced tab allows you to set various functions that affect the performance of the computer. The table below defines the function of each option and its default value. CPU Configuration Multi Core Support Displays the number of active cores. Default: All Limit CPUID Value Enable or disable the Limit CPUID Value feature. Default: Enabl ...

  • Dell W03C - page 89

    Power Management AC Recovery Allows the computer to restore the AC power Loss. Default: Power Off Remote Wake up Allows the computer to be remotely turned on. Default: Enabled Auto Power On Enable or disable the computer to power on automatically. Default: Disabled Post Behavior NumLock Key Enable or disable the NumLock State light during POST. Def ...

  • Dell W03C - page 90

    90 ...

  • Dell W03C - page 91

    32 Diagnostic Error Messages If the computer has an issue or error, it may display a System Message that will help the user identify the cause and action needed to resolve the issue. If the message received is not listed in the following examples, see the documentation for either the operating system or the program that was running when the message ...

  • Dell W03C - page 92

    Diagnostic Error Messages Description • Enter system setup and ensure that the boot sequence information is correct. No timer tick interrupt A chip on the system board might be malfunctioning or motherboard failure USB over current error Disconnect the USB device. The USB device needs more power for it to function properly. Use an external power ...

  • Dell W03C - page 93

    Beep Description Failure Coverage Super I/O chip failure Keyboard controller test failure. 4 RAM Read/Write failure Memory failure 5 RTC Power Fail CMOS battery failure 6 Video BIOS Test Failure Video card failure 7 CPU Failure CPU Diagnostic Power LED Codes Power LED Power State OFF Power is off or the system is in an S4 (hibernate) or S5 (Powered ...

  • Dell W03C - page 94

    94 ...

  • Dell W03C - page 95

    33 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer. System Information System Chipset I ...

  • Dell W03C - page 96

    Video Video Type: Integrated Intel HD / HD 2000 / HD 3000 graphics (depending on processor type) Discrete NVIDIA GeForce GT 525M Video Memory: Integrated up to 384 MB of shared video memory Discrete up to 1 GB Display Type 23 inches HD WLED Dimensions Height 312.50 mm (12.30 inches) Width 533.70 mm (21.01 inches) Diagonal 584.20 mm (23 inches) Maxi ...

  • Dell W03C - page 97

    Communication Wireless internal wireless local area network (WLAN), WiFi, and Bluetooth Expansion Bus Bus type PCIE2.0 Bus speed 5.0 Gb/s Expansion Cards Mobile PCI Express Module WLAN & TVT Mini PCIE Module Drives Externally accessible one 5.25 inch drive bay Internally accessible one 3.5 inch SATA drive bay External Connectors Audio: Left Pan ...

  • Dell W03C - page 98

    System Board Connectors System fan one 3–pin GPU Fan (with discrete GPU) Processor LGA 1155–pin CPU Socket Control Lights And Diagnostic Lights Power light • White light — Solid white light indicates power-on state • Amber light — The computer is in sleep/ standby mode or there might be an issue with the system board or the power supply ...

  • Dell W03C - page 99

    AC Adapter Height 25.40 mm (1.00 inch) 30.00 mm (1.18 inches) Width 154.70 mm (6.10 inches) 155.00 mm (6.10 inches) Depth 76.20 mm (3.00 inches) 76.20 mm (3.00 inches) Temperature range: Operating 0 °C to 40 °C (32 °F to 104 °F) Storage –40 °C to 70 °C (–40 °F to 158 °F) Physical Height 430.00 mm (16.93 inches) Width 568.00 mm (22.36 in ...

  • Dell W03C - page 100

    Environmental Non-Operating 40 G for 22 ms with a change in velocity of 240 inches/s (609 cm/s) Altitude: Operating –15.20 m to 3048 m (–50 ft to 10,000 ft) Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 as defined by ISA-S71.04–1985 100 ...

  • Dell W03C - page 101

    34 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be avai ...

Produzent Dell Kategorie Personal Computer

Dokumente, die wir vom Produzenten des Geräts Dell W03C erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Dell
- Bedienungsanleitungen W03C
- Produktkarten Dell
- Informationsbroschüren
- oder Energieetiketten Dell W03C
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Dell W03C.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Dell W03C, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Dell W03C. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Dell W03C ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Dell W03C, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Dell W03C hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Dell W03C verständlich ist.

Eine gänzliche Bedienungsanleitung von Dell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Dell W03C bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Dell W03C befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Dell W03C, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Dell W03C - die uns die ersten Schritte während der Nutzung von Dell W03C erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Dell W03C hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Dell W03C im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Dell W03C?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Dell W03C nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Dell W03C hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)