Bedienungsanleitung KTI Networks 221TX/3

23 Seiten 0.32 mb
Download

Zur Seite of 23

Summary
  • KTI Networks 221TX/3 - page 1

    24 Installation Guide 10/100 Fast Ethernet Adapters DOC.991105-KF221TX/3-K P/N:750-0132-001 KF-221TX/3 ...

  • KTI Networks 221TX/3 - page 2

    25  1999, KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transforma- tion) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from t ...

  • KTI Networks 221TX/3 - page 3

    23 TRADEMARKS Ethernet is a registered trademark of Xerox Corp. NetW are is a registered trademark of Novell Inc. Intel, Microsoft, T oshiba are trademarks of their respective holders. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the fo ...

  • KTI Networks 221TX/3 - page 4

    21 T able of Contents 1. Introduction 1.1 Adapter Features .............................................................. 1 1.2 Connectors and LEDs ........................................................ 2 2. Wake on LAN T echnology .................................................................................................. 4 3. Installing t ...

  • KTI Networks 221TX/3 - page 5

    1 1. Introduction The 10/100BASE-TX Fast Ethernet PCI Adapter is a 32-bit LAN adapter for use in personal computers with PCI computer bus slots. This adapter is a dual-speed adapter and features one RJ-45 connec- tor for either a 10 Mbps IEEE 802.3 or a 100 Mbps IEEE 802.3u Ethernet network connection over unshielded twisted-pair (UTP) cable. The a ...

  • KTI Networks 221TX/3 - page 6

    2 1.2 Connectors and LEDs Figure 1-1 shows the important components on the adapter . No. Components Description 1 Intel 21 143 LAN controller 2 J P 2 3-Pin Wake on LAN (WOL) connector 3 J P1 PME setting jumper 4 U 5 Remote boot ROM socket 5 Bracket PCI adapter bracket Figure 1-1 Components on the Adapter ...

  • KTI Networks 221TX/3 - page 7

    3 Figure 1-2 shows the connector and LEDs on the bracket. No. Components Description 1 10/100 Mbps This RJ-45 connector requires UTP network connector cable for 10Mbps or 100 Mbps connection. 2 100Mb Link LED This LED lights when 100 Mbps connection is selected and active. 3 10Mb Link LED This LED lights when 10 Mbps connection is selected and acti ...

  • KTI Networks 221TX/3 - page 8

    4 2. W ake on LAN T echnology The adapter is an ACPI-compliant network adapter that supports the following features: _ Power management interface _ Remote wake-up (R WU) ACPI ( Advanced Configuration and Power Management Interface) ACPI is a key element in Operating System Directed Power Man- agement. It is a specification developed by Intel, Micro ...

  • KTI Networks 221TX/3 - page 9

    5 WOL Installation The adapter features : 1. One LAN controller which can support PCI power manage- ment interface and function. 2. One 3-Pin W ake on LAN (WOL) connector (JP2) 3. One PME setting jumper (JP1) 4. One W ake on LAN (WOL) cable The 3-pin WOL connector (JP2) provides an interface to the sys- tem motherboard for auxiliary power and Power ...

  • KTI Networks 221TX/3 - page 10

    6 3. Installing the Adapter This chapter describes how to install the Fast Ethernet PCI adapter in a PCI computer and how to connect the adapter to the network. Before installing the adapter, you need the following:  A computer system that is compliant with the PCI specifica- tions version 2.0 or later .  An available PCI bus master slot in t ...

  • KTI Networks 221TX/3 - page 11

    7 5 . Insert the adapter into the slot and secure the screw (see Figure 3-1). 6. Install the WOL cable, if necessary . Refer to 3.2 for the details. 7. Replace the computer cover and reconnect all previously connected cables. Figure 3-1 Inserting the Adapter into the PCI Slot 3.2 Installing W ake on LAN Cable Follow the steps to install the W ake o ...

  • KTI Networks 221TX/3 - page 12

    8 Figure 3-2 PME Jumper JP1 Setting 4. Locate the 3-Pin WOL connector on the system motherboard. 5. Plug one end of the WOL cable to the 3-Pin WOL connector of the adapter . 6. Plug the other end of the WOL cable to the 3-Pin WOL connector on the system motherboard. Figure 3-3 Installing WOL Cable ...

  • KTI Networks 221TX/3 - page 13

    9 3.3 Connecting to the Network The rear bracket of the Fast Ethernet adapter contains one RJ-45 connector . The connector is used for either 100Mbps 100BASE- TX connection or 10Mbps 10BASE-T connection. The adapter can sense the connection speed and switch to appropriate operation automatically . Figure 3-4 Network Connector RJ-45 Pin Assignment S ...

  • KTI Networks 221TX/3 - page 14

    10 10 Mbps Connection For 10BASE-T Ethernet networks, the Fast Ethernet adapter uses Category 3, 4, or 5 UTP cable. T o establish a valid 10 Mbps connec- tion, the cable must be connected to a 10BASE-T hub. Connect the network cable as follows: 1. Make sure that the plug on the cable is wired appropriately for a standard 10BASE-T adapter . 2. Align ...

  • KTI Networks 221TX/3 - page 15

    11 100 Mbps Connection For 100BASE-TX Fast Ethernet networks, the adapter supports Category 5 UTP cabling. T o establish a valid 100 Mbps connection, the cable must be connected to a 100BASE-TX hub. 1. Make sure that the plug on the cable is wired appropriately for a standard 100BASE-TX adapter . 2. Align the RJ-45 plug on the end of the UTP cable ...

  • KTI Networks 221TX/3 - page 16

    12 4. Network Driver Installation After making the connection to the network, you must install the adapter network driver in order to connect the Fast Ethernet adapter to your network operating system. 4.1 Driver Information The adapter driver media contains the latest versions of the network drivers available when the adapter is shipped from the f ...

  • KTI Networks 221TX/3 - page 17

    13 In addition to the basic drivers, more updated information and driv- ers may be included in the driver media after this guide is published. Please refer to the README.DOC file first for the latest informa- tion before you install any drivers. 4.2 BIOS Setup Before installing the driver, it is recommended to run the system BIOS setup utility to ...

  • KTI Networks 221TX/3 - page 18

    14 4.3 Installation for Windows 98 System After the driver installation for Windows 98, there are some simple methods to check the installation is proper or not as follows: 1. Check Device Manager in System Properties window Figure 4-1 Device Manager ...

  • KTI Networks 221TX/3 - page 19

    15 The adapter name shown in Device Manager should be "KF221TX Fast Ethernet PCI Adapter". The installation is proper if there is no "?" or "!" mark ahead of the adapter line. 2. If you are using TCP/IP protocol, you can use Ping command under DOS mode to check the adapter itself. The command is >ping 127.0.0.1 Figu ...

  • KTI Networks 221TX/3 - page 20

    16 5. LED Indicators Each Fast Ethernet adapter has three LEDs, as shown in Figure 1-2. 5.1 Interpretations The interpretations of the LEDs are: 100Mb LED indicates an active 100Mbps connection is established. O n : Good connection between adapter and 100BASE-TX device Off : No active connection Blink: Not applicable 10Mb LED indicates an active 10 ...

  • KTI Networks 221TX/3 - page 21

    17 Appendix A1. Specifications Network std.: 10 Mb psIEEE 802.3 10BASE-T Ethernet 100 Mbps IEEE 802.3u 100BASE-TX Fast Ethernet Speed : Auto-sense, auto-negotiation, 10Mbps, 100Mbps Duplex : Auto-negotiation, Half-duplex and full-duplex Bus Interface: PCI 2.0 or later Network Cable: 10Mbps Category 3, 4, or 5 UTP (100 meters) 100Mbps Category 5 UTP ...

  • KTI Networks 221TX/3 - page 22

    18 A.2 Auto-negotiation Function The adapter is equipped with an auto-negotiation function. Auto- negotiation is a negotiation procedure between two connected de- vices. Both devices must be auto-negotiation capable. The proce- dure decides the best operation modes that can be used for the data transfer operation between two connected devices. The ...

  • KTI Networks 221TX/3 - page 23

    19 A.3 Installing Remote Boot ROM Before you can use the remote boot function, you have to setup the remote boot service on the file server and install the remote boot ROM onto the adapter . T o install the boot ROM, make sure the notch of the boot ROM is in the same direction as the notch of the socket on the adapter . The remote boot ROM socket i ...

Produzent KTI Networks Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts KTI Networks 221TX/3 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen KTI Networks
- Bedienungsanleitungen 221TX/3
- Produktkarten KTI Networks
- Informationsbroschüren
- oder Energieetiketten KTI Networks 221TX/3
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung KTI Networks 221TX/3.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen KTI Networks 221TX/3, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen KTI Networks 221TX/3. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts KTI Networks 221TX/3 ansehen.

Die komplette Bedienungsanleitung des Geräts KTI Networks 221TX/3, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von KTI Networks 221TX/3 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von KTI Networks 221TX/3 verständlich ist.

Eine gänzliche Bedienungsanleitung von KTI Networks sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von KTI Networks 221TX/3 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von KTI Networks 221TX/3 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich KTI Networks 221TX/3, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts KTI Networks 221TX/3 - die uns die ersten Schritte während der Nutzung von KTI Networks 221TX/3 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit KTI Networks 221TX/3 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von KTI Networks 221TX/3 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich KTI Networks 221TX/3?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit KTI Networks 221TX/3 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit KTI Networks 221TX/3 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)