Bedienungsanleitung Stanley Black & Decker PG10

22 Seiten 1.57 mb
Download

Zur Seite of 22

Summary
  • Stanley Black & Decker PG10 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 65846 2/2015 V er . 6 USER MANUAL Safety , Operation and Maintenance PG10 HYDRAULIC PROFILE GRINDER ...

  • Stanley Black & Decker PG10 - page 2

    2 ► PG10 User Manual DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ _________ ___________ ___________ _________ ___________ _________ ___ I, the undersigned: Ich, der Unterzeichnende: Je soussi gné: El abajo firmante: lo so ...

  • Stanley Black & Decker PG10 - page 3

    PG10 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer . Please read the following warning. For the nearest authorized and certie ...

  • Stanley Black & Decker PG10 - page 4

    4 ► PG10 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker PG10 - page 5

    PG10 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Review them carefully before operating the tool and before per- forming general maintenance or repairs. ...

  • Stanley Black & Decker PG10 - page 6

    6 ► PG10 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA TOR. SEE OTHER SIDE 1. FAILURE TO USE H ...

  • Stanley Black & Decker PG10 - page 7

    PG10 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker PG10 - page 8

    8 ► PG10 User Manual HOSE RECOMMENDA TIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTR ...

  • Stanley Black & Decker PG10 - page 9

    PG10 User Manual ◄ 9 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity ...

  • Stanley Black & Decker PG10 - page 10

    10 ► PG10 User Manual PRE-OPERA TION PROCEDURES CHECK HYDRAULIC POWER SOURCE 1. Using a calibrated ow meter and pressure gauge, check that the hydraulic power source develops a ow of 7–10 gpm/26–38 lpm at 2200–2300 psi/152– 159 bar . 2. Make certain the hydraulic power source is equipped with a relief valve set to open at 2100–225 ...

  • Stanley Black & Decker PG10 - page 11

    PG10 User Manual ◄ 1 1 OPERA TING PROCEDURES 1. Observe all safety precautions. 2. Always start the grinder with the grinding wheel away from the work surface by turning the hand wheel counter clockwise to raise the wheel. 3. Move the hydraulic circuit control valve to the ON position. 4. Squeeze the trigger momentarily . If the grinder does not ...

  • Stanley Black & Decker PG10 - page 12

    12 ► PG10 User Manual 1. The gears and bearings in the ram, spindle, and housing assemblies should be regreased every 6 months or 500 hours. This procedure must be ac- complished by a trained technician. 2. After each servicing, measure the spindle speed (rpm – revolutions per minute) at 12 gpm/45 lpm in - put. The nominal speed is 4000, not to ...

  • Stanley Black & Decker PG10 - page 13

    PG10 User Manual ◄ 13 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system. • Always store the tool in a clean d ...

  • Stanley Black & Decker PG10 - page 14

    14 ► PG10 User Manual PROBLEM CAUSE SOLUTION Grinder does not run. Hydraulic power source not functioning. Check power source for proper ow and pressure (7–10 gpm/26–38 lpm @ 1500–2000 psi/ 105–140 bar . Couplers or hoses blocked. Locate and remove restriction. Hydraulic motor failure. Inspect and repair . Hydraulic lines not connected ...

  • Stanley Black & Decker PG10 - page 15

    PG10 User Manual ◄ 15 Wheel Capacity ............................................................. 6 in. dia. × 3 in. thk × 5/8-1 1 threaded arbor (T ype 6) U.S.A. Pressure Range................................................................................................................ 1000–2000 psi/70–140 bar Maximum Back Pressure..... ...

  • Stanley Black & Decker PG10 - page 16

    16 ► PG10 User Manual PG10 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker PG10 - page 17

    PG10 User Manual ◄ 17 PG10 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker PG10 - page 18

    18 ► PG10 User Manual ITEM P/N QTY DESCRIPTION 1 25294 2 HOSE ASSY 2 00713 2 DOWEL PIN 3 06854 1 IDLER SHAFT 4 25717 1 IDLER GEAR 5 00178 1 O-RING, 2-1/8 × 2-1/4 × 1/16 70D • 6 00669 1 QUAD RING • 7 19884 1 SEAL GLAND 8 25166 1 MOTOR SHAFT 9 00148 1 BEARING 10 00166 1 RET AINING RING 11 00120 8 CAPSCREW 12 01604 3 O-RING (INCL WITH ITEM 1) ...

  • Stanley Black & Decker PG10 - page 19

    PG10 User Manual ◄ 19 ITEM P/N QTY DESCRIPTION 88 03973 1 MALE COUPLING, P ARKER 47437 1 MALE COUPLING, AEROQUIP 89 25842 1 WRENCH (SHIPPED LOOSE) 90 17904 1 RET AINING RING 91 18008 2 SPRING WASHER 92 24819 1 SPRING 93 28914 1 FLOW CONTROL (PRE-SET) 94 00955 1 PIPE PLUG 95 24289 1 PLUG 96 0141 1 1 O-RING, .488 × .624 × .078 -906 • 97 20145 1 ...

  • Stanley Black & Decker PG10 - page 20

    20 ► PG10 User Manual ITEM P/N QTY DESCRIPTION 1 69915 1 SP ARK BARRIER SECONDARY 2 69899 1 GUARD WELDMENT 3 65202 1 SP ARK BARRIER 4 62402 1 SP ARK GUARD FRAME WELDMENT 5 2072 8 CAPSCREW 6 70743 9 F ABRIC SNAP 7 2395 9 CABLE TIE (NOT PICTURED) 69814 1 SP ARK GUARD ASSY (INCL ITEMS 3 & 4) 69820 1 SP ARK GUARD KIT (INCL ITEMS 1 THRU 7 SP ARK G ...

  • Stanley Black & Decker PG10 - page 21

    ...

  • Stanley Black & Decker PG10 - page 22

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Produzent Stanley Black & Decker Kategorie Grinder

Dokumente, die wir vom Produzenten des Geräts Stanley Black & Decker PG10 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Stanley Black & Decker
- Bedienungsanleitungen PG10
- Produktkarten Stanley Black & Decker
- Informationsbroschüren
- oder Energieetiketten Stanley Black & Decker PG10
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Stanley Black & Decker PG10.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Stanley Black & Decker PG10, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Stanley Black & Decker PG10. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Stanley Black & Decker PG10 ansehen.

Die komplette Bedienungsanleitung des Geräts Stanley Black & Decker PG10, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Stanley Black & Decker PG10 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Stanley Black & Decker PG10 verständlich ist.

Eine gänzliche Bedienungsanleitung von Stanley Black & Decker sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Stanley Black & Decker PG10 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Stanley Black & Decker PG10 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Stanley Black & Decker PG10, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Stanley Black & Decker PG10 - die uns die ersten Schritte während der Nutzung von Stanley Black & Decker PG10 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Stanley Black & Decker PG10 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Stanley Black & Decker PG10 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Stanley Black & Decker PG10?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Stanley Black & Decker PG10 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Stanley Black & Decker PG10 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)