Bedienungsanleitung Genie 1000

14 Seiten 1.85 mb
Download

Zur Seite of 14

Summary
  • Genie 1000 - page 1

    SilentMax ™ 1000 Includes INTELLICODE ® 2 Remote Control. Safe-T-Beam ® System must be installed to close door. For use only with residential sectional or one piece overhead garage doors. Homelink ® and Car2U ® compatible. For Answers and Assistance: 1.800.354.3643 or visit www.geniecompany.com WARNING: To reduce the risk of injury to persons ...

  • Genie 1000 - page 2

    THIS P AGE LEFT BLANK ...

  • Genie 1000 - page 3

    T ABLE OF C ONTENTS Section .............................................................. Page Safety Information 2 .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Instructions .2 Safety Features / Opener Features .3 G - 1 etting Started Overvie ...

  • Genie 1000 - page 4

    SAFET Y FEA TURES Safe-T-Beam® (STB) Non-Contact Reversing S ystem Puts an in visible beam across the door opening. The door stops and reverses to the full open position if anything th passes rough the beam. LED indicator lights on the powerhead and on the STBs p rovide a self diagnostic code if an operational problem exists. Safe-T-Rev erse® Con ...

  • Genie 1000 - page 5

    4 ©2011 The Genie Company 9/2011 SET PROGRAM Open Tr a v e l ROUND LED Indicator F acing Garage Door Close Tr av e l Button O VERVIEW OF PO WERHEAD C ONTROLS This section describes the simple programming functions. Use this page to familiarize yourself with the buttons and LED indicators used to program the opener . NO TE: These and buttons are fo ...

  • Genie 1000 - page 6

    ©2011 The Genie Company 9/2011 5 W ARNING s Make sure door way is in view and clear of obstacles and people to a void injury or damage to proper ty . s DO NOT operat e this unit from wall console before LIMITS and FORCE a re set. Severe damage to the opener can occur. s The bullet MUST be engaged to carriage BEFORE setting limit s. See Installatio ...

  • Genie 1000 - page 7

    ©2011 The Genie Company 9/2011 6 PROGRAMMING REMOTES to New Intellicode® 2 Openers. All type remotes program in the same way. Bring remote(s) to powerhead location. For Car2U® and HomeLink®, park car outside the garage with the ignition key in the “ACCESSORY” position. Each button must be programmed individually following steps below. NOTE: ...

  • Genie 1000 - page 8

    7 ©2011 The Genie Company 9/2011 IntelliCode® 1 or 2 wireless keypad Door moves. (To verify memory is cleared—try to operate the garage door using one of your remote devices. The opener should not respond.) Both LEDs OFF confirms communication is established with operator . Round LED BL UE then OFF , Long LED FLASHING PROGRAM SET Press & ho ...

  • Genie 1000 - page 9

    8 ©2011 The Genie Company 9/2011 s With the door closed , pull release handle DOWN and let go to release door carriage assembly f rom drive system. s R s Raise and lower the door manually—it should move freely and smoothly. ’d n a t e e f 4 o t 3 y l e t a m i x o r p p a y l l a u n a m r o o d e s i a let go. – Door should r ...

  • Genie 1000 - page 10

    9 ©2011 The Genie Company 9/2011 CORRECTIVE MAINTENANCE TO ENGAGE , PULL DOWN AND TOWARD POWERHEAD . CHECK THE RED BLOCK IS IN THE UP POSITION. THEN LET GO. TO DISENGAGE , PULL DOWN AND TOWARD DOOR . CHECK RED BLOCK IN THE DOWN POSITION. THEN LET GO. DOOR DOOR DISENGAGING AND ENGAGING CARRIAGE CHANGE LIGHT BULBS W ARNING s When replacing light cov ...

  • Genie 1000 - page 11

    ©2011 The Genie Company 9/2011 10 ADJUSTMENT GUIDE - FORCE SETTINGS F orce settings are pre-programmed at the factory and "learned" during the Open/Close Limit settings steps. For normal use, these settings should not need adjustment with this unit. Howev er , conditions possibly requiring adjustment are: Doors with very stiff weather se ...

  • Genie 1000 - page 12

    11 ©2011 The Genie Company 9/2011 REFERENCE - CIRCUIT WIRING DIA GRAM FOR HELP-1-800-35-GENIE OR WWW .GENIECOMP ANY .COM Opener circuit wiring diagram. This wiring diagram is for reference only . Opening C over Ma y Cause Electric Shock. Disconnect pow er from opener prior to remo ving cov er . 1 2 3 4 5 6 12 3 76 POWER CORD CONNECTOR WHITE BLACK ...

  • Genie 1000 - page 13

    Opener does NO T run from wall console . s Check power source , – Plug a lamp into outlet used for powerhead . If lamp works, power source is OK. – If not, check fuse or circuit breaker . s If power is OK, – Check connections at powerhead terminals and at wall console. – Limits must be set with door arm connected to door . s Check ...

  • Genie 1000 - page 14

    13 ©2011 The Genie Company 9/2011 TROUBLESHOO TING GUIDE - POWERHEAD LEDs FOR HELP-1-800-35-GENIE OR WWW .GENIECOMP ANY .C OM P owerhead LED P ossible Problem Solution Round LED Long LED OFF OFF Normal operation None required No response from unit Check power supply Contact a trained door system technician ON/RED/ STEADY ON/RED/ STEADY Limits NO T ...

Produzent Genie Kategorie Garage Door Opener

Dokumente, die wir vom Produzenten des Geräts Genie 1000 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Genie
- Bedienungsanleitungen 1000
- Produktkarten Genie
- Informationsbroschüren
- oder Energieetiketten Genie 1000
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Genie 1000.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Genie 1000, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Genie 1000. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Genie 1000 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Genie 1000, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Genie 1000 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Genie 1000 verständlich ist.

Eine gänzliche Bedienungsanleitung von Genie sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Genie 1000 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Genie 1000 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Genie 1000, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Genie 1000 - die uns die ersten Schritte während der Nutzung von Genie 1000 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Genie 1000 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Genie 1000 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Genie 1000?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Genie 1000 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Genie 1000 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)