Bedienungsanleitung Husqvarna LTH1742T

32 Seiten 1.09 mb
Download

Zur Seite of 32

Summary
  • Husqvarna LTH1742T - page 1

    03002 L TH1742T L TH1742TWIN Operator's Manual ...

  • Husqvarna LTH1742T - page 2

    2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine. • ...

  • Husqvarna LTH1742T - page 3

    3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or ...

  • Husqvarna LTH1742T - page 4

    4 PRODUCT SPECIFICA TIONS Gasoline Capacity 1.5 Gallons and type: Unleaded Regular Oil T ype (API-SG-SL): SAE 10W -30 (above 32°F) SAE 5W -30 (below 32°F) Oil Capacity: W/Filter: 60.8 oz Spark Plug: Champion RCJ8Y (Gap: .030") Ground Speed (MPH): Forward: 5.2 Reverse: 2.9 Charging System: 14 Amps Battery: AMP/HR: 28 MIN. CCA: 230 CASE SIZE: ...

  • Husqvarna LTH1742T - page 5

    5 UNAS SEMBLED P ARTS Steering Wheel (1) W asher Seat (1) Seat Steering Boot Steering Extension Shaft Steering Wheel Adapter Keys (2) K eys Slope Sheet (1) Oil Drain T ube F or Future Use (1) He x Bolt (1) He x Bolt (1) 5/16 Lock W asher (1) Large Flat W asher Steering Wheel Inser t (1) Hood Scoop ...

  • Husqvarna LTH1742T - page 6

    6 AS SEMBL Y Y our new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. T o ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely . Use the correct tools as necessary to insure proper tightness. BEFORE REMOVING TRACTOR FROM SKID ...

  • Husqvarna LTH1742T - page 7

    7 AS SEMBL Y Fig. 3 INST ALL SEA T (See Figs. 2 and 3) • Remove bolt and flat washer se cur ing seat to cardboard packing and set aside for as sem bly of seat to tractor . Remove the cardboard packing and discard. • Connect switch to seat. • Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan. Fi ...

  • Husqvarna LTH1742T - page 8

    8 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING? ...

  • Husqvarna LTH1742T - page 9

    9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVERS ...

  • Husqvarna LTH1742T - page 10

    10 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the safety standards of the American National Stand ...

  • Husqvarna LTH1742T - page 11

    11 OPERA TION 00155 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op- erating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. HOW T ...

  • Husqvarna LTH1742T - page 12

    12 OPERA TION TO MOVE FORWARD AND BACK WARD (See Fig. 10) The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake. • Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed. K L Fig. 10 TO ...

  • Husqvarna LTH1742T - page 13

    13 OPERA TION Fig. 13 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERA TING) 0 2 8 2 8 TO TRANSPORT (See Fig. 14) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po si tion. F ree wheel control is located at the rear drawbar of tractor . • Raise attachm ...

  • Husqvarna LTH1742T - page 14

    14 OPERA TION BEFORE ST ARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped, from the factory , already filled with sum mer weight oil. • Check engine oil with tractor on level ground. • Unthread and remove oil fill cap/dipstick; wipe oil off. Reinsert the dipstick into the tube and rest oil fill cap on the tube ...

  • Husqvarna LTH1742T - page 15

    15 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om- mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de vel- op ...

  • Husqvarna LTH1742T - page 16

    16 MAINTENANCE LUBRICA TION CHART T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery . 1 , ...

  • Husqvarna LTH1742T - page 17

    17 MAINTENANCE 02 54 5 MANDREL ASSEMBL Y BL ADE TRAILING EDGE UP BL ADE BOL T CENTER HOLE ST AR TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad j ...

  • Husqvarna LTH1742T - page 18

    18 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission ...

  • Husqvarna LTH1742T - page 19

    19 CLEANING • Clean engine, battery , seat, finish, etc. of all foreign matter . • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep wate ...

  • Husqvarna LTH1742T - page 20

    20 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key . • Make sure the blades and all moving parts have completely stopped. ? ...

  • Husqvarna LTH1742T - page 21

    21 SERVICE AND ADJUSTMENTS • A TT ACH FRONT LINK (E) - W ork from left side of trac- tor . Insert rod end of link assembly through front hole in tractor front suspension bracket (F). • Insert end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spring (J). E F H J Fig. 24 • Install belt onto electric clutch ...

  • Husqvarna LTH1742T - page 22

    22 SERVICE AND ADJUSTMENTS • If adjustment is necessary , see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT -TO-BACK ADJUSTMENT (See Figs. 29 & 30) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adj ...

  • Husqvarna LTH1742T - page 23

    23 SERVICE AND ADJUSTMENTS Fig. 32 TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 31) The mower blade drive belt may be replaced without tools. P ark the tractor on level surface. Engage parking brake. BEL T REMOV AL - • Remove mower from tractor (See “TO REMOVE MOW ER” in this section of this manual). • Work belt off both mandrel pulleys a ...

  • Husqvarna LTH1742T - page 24

    24 Fig. 34 SERVICE AND ADJUSTMENTS Fig. 33 0 0663 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer - ing wheel and reassemble per instructions in the Assembly section of this ...

  • Husqvarna LTH1742T - page 25

    25 SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBL Y (See Fig. 35) • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Grasp hood at sides, tilt toward engine and lift off of tractor . • T o replace, reverse above procedure. Fig. 35 02778 HEADLIGHT WIRE CONNECTOR HOOD TO REPL ACE HEADLIGHT BULB • Raise ...

  • Husqvarna LTH1742T - page 26

    26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Husqvarna LTH1742T - page 27

    27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter . 5. Clean/replace air filter . 6. Dirty fuel filte ...

  • Husqvarna LTH1742T - page 28

    28 TROUBLESHOOTING POINTS Engine continues to run 1. F aulty operator -safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department. engaged Poor cut - uneven 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade ...

  • Husqvarna LTH1742T - page 29

    29 SERVICE NOTES ...

  • Husqvarna LTH1742T - page 30

    30 SERVICE NOTES ...

  • Husqvarna LTH1742T - page 31

    31 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Husqvarna LTH1742T - page 32

    532 41 73-88 Rev . 2 02.25.09 SR Printed in the U.S.A. ...

Produzent Husqvarna Kategorie Lawn Mower

Dokumente, die wir vom Produzenten des Geräts Husqvarna LTH1742T erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Husqvarna
- Bedienungsanleitungen LTH1742T
- Produktkarten Husqvarna
- Informationsbroschüren
- oder Energieetiketten Husqvarna LTH1742T
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Husqvarna LTH1742T.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Husqvarna LTH1742T, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Husqvarna LTH1742T. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Husqvarna LTH1742T ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Husqvarna LTH1742T, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Husqvarna LTH1742T hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Husqvarna LTH1742T verständlich ist.

Eine gänzliche Bedienungsanleitung von Husqvarna sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Husqvarna LTH1742T bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Husqvarna LTH1742T befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Husqvarna LTH1742T, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Husqvarna LTH1742T - die uns die ersten Schritte während der Nutzung von Husqvarna LTH1742T erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Husqvarna LTH1742T hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Husqvarna LTH1742T im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Husqvarna LTH1742T?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Husqvarna LTH1742T nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Husqvarna LTH1742T hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)