Bedienungsanleitung La Crosse Technology TX5U

28 Seiten 0.5 mb
Download

Zur Seite of 28

Summary
  • La Crosse Technology TX5U - page 1

    WS-7095U Wireless 433 MHz 24” Wall Hanging Wireless Weather Center Instruction Manual , 1 P  ...

  • La Crosse Technology TX5U - page 2

    2 TABLE OF CONTENTS Topic Page Inventory of Con tents/Addition al Equipment: 3 Quick Set-U p Guide: 3 Detailed Set-Up Guide Battery Installation: 4 LCD Screens: 5 Program Mode Function Buttons: 6 LCD Contrast: 6 12/24-hour Time Display: 6 Time Setting: 6-7 Time Zone Setting: 7 Date Setting: 7 Date Displa y: 7 Selecting ° F or ° C and Inches or Mi ...

  • La Crosse Technology TX5U - page 3

    3 INVENTORY OF CO NTENTS 1. WS-7095U—24” W all Hang ing Wireless Weather Center (Figure 1). 2. TX4U—Remote Therm o-Hygro (temperature-humidity) Sensor: includes a mounting brac ket/receptor, rain cover, t wo mounting scre ws, and adhesive tape (Fi gu re 2) . 3. TX5U—Rainf all Sensor: incl udes a base, rainfall collector, and two mounting sc ...

  • La Crosse Technology TX5U - page 4

    4 DETAILED SET-UP GUIDE I. BATTERY INSTALLATION Batteries will fit tightly. To avoid start-up problems, make sure th at th e batteries do not spring free. A. REMOTE THERMO-HYG RO SENSOR 1. Pull the cylindrical rain cover off the sensor. 2. Remove the battery cover (locat ed on the backsi de of the se nsor, above the mounting post and bracke t). Pre ...

  • La Crosse Technology TX5U - page 5

    5 C. WEATHER CENTER 1. Remove t he battery cover. To do this, place a solid object in the space provided at the l ower- central position of the battery cover (the cove r has whi t e writing on it) then push up and pull out on the batt e ry cove r. 2. Observe the correct polarity, and install three C batteries. 3. Replace the battery cove r. THE LCD ...

  • La Crosse Technology TX5U - page 6

    6 PROGRAM MODE The Program Mode is laid out in a ma nner that allows you to program each function separatel y, or you can foll ow the instructions en tirely to program the Weather Center. Complete programm ing is usually done for the initial set-up, and will require you to skip st ep 1 of each programming section (from section III to XII). The prog ...

  • La Crosse Technology TX5U - page 7

    7 4. Press the SET button t o confirm , and to advance to the Time setting m ode. IV. TIME SETTING Note: The default time, after battery installation is “12:00.” The Weather Center will begin to keep track of time after this. 1. Press the SET button three times to enter the Time setting mode. 2. The hour digit will flash in LCD 1. 3. Press the ...

  • La Crosse Technology TX5U - page 8

    8 VII. DATE DISPLAY SETTING 1. Press the SET button nine times to enter the Date Display setting mode. 2. The default “month/date/year” disp lay will flash in LCD 2. 3. Press the CH/+ button to togg le b etween the default setting and the “weekday/month/day” setting. 4. Press the SET button to c onfirm, and t o advance to select ° F or ° ...

  • La Crosse Technology TX5U - page 9

    9 X. DISPL AYING RELATIVE hPa/inHg OR ABSOLUTE hPa/inHg Note: Air pressure can be displayed in four different m easu r es: Relative hPa/inHg and Ab so lute hPa/inHg. Absolute settings give a tru e and real-ti me air press ure reading ( at user’s loc ation) that cannot be manually calibra ted. Rela tive air pressure is measured in relatio n to sea ...

  • La Crosse Technology TX5U - page 10

    10 XI. MANUALLY SETTING THE R ELATIVE AIR PRESSURE 1. Press the SET button thirteen times to enter the Manual Setting of the Relative Air Pressure mode. 2. The air pressure digits in LCD 4 will flash. Use the CH/+ button to set the appropriate Relative Ai r Pressure (check local weather service). 3. Press the SET button t o confi rm, and to advance ...

  • La Crosse Technology TX5U - page 11

    11 FEATURES & OPERATIONS I. MOON PHASE The Moon Phases, and their corres p onding dates and tide lev els, appear in LCD 2. While viewing LCD 2 in the normal display mo d e, the current moon phase, corresp ond ing tide level, an d cu rrent date are all displayed. There are 8 visible Moon Phases th at will show in the LCD: The Weather C enter is ...

  • La Crosse Technology TX5U - page 12

    12 every moon phase and its begi nni ng dates until the year 2020 (wrapping aro und to 1998). Note: The Moon Phase f eatures allow for the discovery of dates of specific moon phases. Hypo thetica lly, if the date of the next full moon were desired ( and the current moon phase was not a f ull moon), simply press the MOON butto n, press th e CH/+ but ...

  • La Crosse Technology TX5U - page 13

    13 Note: The time and date will automatically and simultaneously appear in their respective LCD’s fo r all following steps in this section. 2. Press the MIN/MAX button a second time. The flashing mi nimum temperature in LCD 3 s hifts to flash the recorde d maximum temperature. 3. Press the MIN/MAX button a third time. In LCD 6 the Current Outdoor ...

  • La Crosse Technology TX5U - page 14

    14 , 1 Comfort Level Indicator Sunny— indicates that th e w eather is expected to impro ve (not that the weather will be sunny). Sun with Clou ds— indicates that the weather is ex pected to be fair (not that the weather will be sunn y with clouds). Clouds with Rain — indicates that the weather is e xpected to get worse (not that the weather w ...

  • La Crosse Technology TX5U - page 15

    15 the indoor humidity. The indicator will display a “happy -face” when the temperature is between 68 ° F and 79 ° F (20 ° C and 25.9 ° C), and the humidity is between 45% and 64%. A “sad-face” will be displayed when the temperature and humidity are outside t he mentioned ra nges. If the humidity is below 45% the word “DRY” will app ...

  • La Crosse Technology TX5U - page 16

    16 air pressure has a risi ng trend, and the weather s hould improve. If the bars are dropping (l ower on the rig ht than the left) then t he air pressure has a falling trend, and th e weathe r sho uld worsen. B. RAINFALL HISTORY The bar graph will also display the rainfall histor y; th is mode is indicated by the appearance of the word “RAIN” ...

  • La Crosse Technology TX5U - page 17

    17 The bar graph displays the columns sequ entially from “0” to “7” until all columns are sho wing. Then th ey are h idden again, and th e sequential display is repeated. It is possible to read each column, one at a tim e—simulta neously dis playing the numeric measurement for that column direc tl y under the bar graph. To do this: 1. Pre ...

  • La Crosse Technology TX5U - page 18

    18 VI. RESETTING RAINFALL INFORMATION A. RAINFALL QU ANTIT Y TOTALS Resetting the Rainfall Quantity To tals will clear the numeric data held under “TOTAL,” “1h,” and “24h ,” resetting all to 0.00 (appearing in LCD 5). From any selected normal display mode: 1. Press and hold the RAIN button fo r 3 sec o nds . 2. Resetting will automatica ...

  • La Crosse Technology TX5U - page 19

    19 C. HARD RESET OF EEP ROM WEATHER CENTER MEMORY Note: This is to be used if there are problems with tran smission, or if the rainfall hi story bar g raph needs to be cleared. 1. Remove the batteries and wait 30 seconds. (This will also reset the Rainfall Quantity Totals). 2. Checking the polarity, install batteries. 3. During the brief 2 seconds ...

  • La Crosse Technology TX5U - page 20

    20 A. SET-UP OF MULTIPLE SENSORS Note: The first sens or signal that t he Weather Center receives is automatic al l y assi g ne d as the “boxed #1.” The 2 nd to be received is the “boxed #2,” and the 3 rd is the “boxe d #3.” 1. It is necessary to remove the batteries from all units currently in operation. 2. Remove the battery cove rs t ...

  • La Crosse Technology TX5U - page 21

    21 I. THE TX4U—REMOTE TH ERMO-HYGRO SENSOR The TX4U—R emote Therm o-Hygro Se nsor can be mounte d in two way s: • with the use of screws or, • using the a dhesive tape. A. MOUNTING WITH THE SCREWS 1. Remove the mounting bracket/r eceptor from the packagi ng. 2. Place the mounting bracket over the desire d m ounting surface. Through the 2 sc ...

  • La Crosse Technology TX5U - page 22

    22 II. THE TX5U—RAI NFALL SENSOR The Rainfall Sensor can be mounted in two ways: • simply placing it in a desired location, or • mounting it to surface with the provided screws. Ensure that the Rain fall Sen sor is completely horizontal and stab le. 1. Rotate the rainfall collector separating it from the base. 2. There are t wo cylindri cal h ...

  • La Crosse Technology TX5U - page 23

    23 2. Install f our mounti ng screws (not i ncluded) into a wall within transmissi on range— leaving approximately 3/16 of an i nch (5mm ) extended from the wall for the center s crews, and 11/16 of a n inch (18mm) extended from the wall for the two out er screws. 3. Place the Weather Center onto the scre ws, usin g the hanging holes on th e back ...

  • La Crosse Technology TX5U - page 24

    24 MAINTENAN CE AND CA RE • Extreme tem peratures, vib rations, an d shock sh ould be av oided to preve nt damage to the units. • Clean displays an d units with a soft, da mp cloth. Do not use sol vents or scouring agen ts—th ey may mark and damage the displays an d casings. • Do not submerge in wa ter. • Immediatel y remove all l ow powe ...

  • La Crosse Technology TX5U - page 25

    25 SPECIFICATIONS Weather Center—rec ommended operating te mperature: 32 ° F to 122 ° F (0 ° C to 50 ° C). LCD contrast: 16 levels (0-15). Moon phase time span: 29 Dec. 98 to 10 Jan. 2020. Temperature measuring range Indoor: 14 ° F to 140 ° F with 0.2 ° F resolution. (-9.9 ° C to 59.9 ° C with 0.1 ° C resol ution). “OFL” displayed i ...

  • La Crosse Technology TX5U - page 26

    26 Outdoor humidity: Every 10 seconds for the first 12 minutes, then ev er y 5 minutes . Rain quantity: Every 10 second s for the first 12 minutes, then ev er y 5 minutes . Sensor readin g update Outdoor temperature: Every 1 minut e. Outdoor hum idity: Every 1 minut e. Rain quantity upd ate (Rain Gaug e): Updates every tip of the bu cket. Depending ...

  • La Crosse Technology TX5U - page 27

    27 WARRANTY INFORMA TION La Crosse Technolog y, Ltd pr ovides a 1- year limited warranty on this product against manufacturing defects in materia ls a nd workmanship. This limited warranty begins o n the origin al date of purchas e, is valid only on products purchased and used in North Amer i ca and only to the original pur chaser of this product. ...

  • La Crosse Technology TX5U - page 28

    28 This warranty gives you spec ific leg al rights. You may also have other rights specific to your State. Some States do no allo w the exclusi on of cons equential or incidental damages theref or e the above exclusion of limit ation may not apply to you. For warranty work, technical support, or information contact: La Crosse Technolog y 2809 Losey ...

Produzent La Crosse Technology Kategorie Portable Radio

Dokumente, die wir vom Produzenten des Geräts La Crosse Technology TX5U erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen La Crosse Technology
- Bedienungsanleitungen TX5U
- Produktkarten La Crosse Technology
- Informationsbroschüren
- oder Energieetiketten La Crosse Technology TX5U
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung La Crosse Technology TX5U.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen La Crosse Technology TX5U, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen La Crosse Technology TX5U. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts La Crosse Technology TX5U ansehen.

Die komplette Bedienungsanleitung des Geräts La Crosse Technology TX5U, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von La Crosse Technology TX5U hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von La Crosse Technology TX5U verständlich ist.

Eine gänzliche Bedienungsanleitung von La Crosse Technology sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von La Crosse Technology TX5U bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von La Crosse Technology TX5U befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich La Crosse Technology TX5U, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts La Crosse Technology TX5U - die uns die ersten Schritte während der Nutzung von La Crosse Technology TX5U erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit La Crosse Technology TX5U hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von La Crosse Technology TX5U im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich La Crosse Technology TX5U?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit La Crosse Technology TX5U nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit La Crosse Technology TX5U hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)