-
National Instruments cFP-20xx - page 1
FieldPoint TM cFP-20 xx Quick Start Guide What Y ou Need to Get Set Up • cFP-20 xx LabVIEW RT controller • Mounting hardware (DIN rail, panel- mount, or rack-mount accessory) • I/O module(s) • cFP-BP- x backplane, connector blocks, cables • 11–30 V power supply • Accessories: Ethernet cable, number 2 Phillips screwdriver • PC runnin ...
-
National Instruments cFP-20xx - page 2
106 mm (4.18 in.) Cabling Clearance Min. 182 mm (7.18 in.) 4 slots = 246 mm (9.68 in.) 8 slots = 441 mm (17.4 in.) Cooling Outline 51 mm (2 in.) Cooling Outline 51 mm (2 in.) 127 mm (5.00 in.) Cabling Clearance Min. 165 mm (6.50 in.) Cooling Outline 51 mm (2 in.) All Around 4 slots = 246 mm (9.68 in.) 8 slots = 441 mm (17.4 in.) 2 cFP-20xx Quick St ...
-
National Instruments cFP-20xx - page 3
3 cFP-20xx Quick Start Guide © National Instruments Corporation Mounting the Backplane on a Panel A. Fasten the panel-mount plates to the back of the cFP-BP- x using a number 2 Phillips screwdriver and the 8-32 × 5/16 in. countersink screws shipped with the kit. B. Bolt or screw the panel-mount accessory to a panel. C. Connect the PE ground termi ...
-
National Instruments cFP-20xx - page 4
4 cFP-20xx Quick Start Guide ni.com Mounting the Backplane on a DIN Rail NI recommends DIN rail mounting for the cFP-BP-4 only . Use panel mounting or rack mounting for the cFP-BP-8. A. Fasten the DIN rail clip(s) to the cFP-BP- x using a number 2 Phillips screwdriver and the 8-32 × 5/16 in. countersink screws shipped with the clip(s). B. Insert o ...
-
National Instruments cFP-20xx - page 5
Mounting the Backplane in a Standard 19-in. Rack A. Fasten the rack-mount bracket to the back of the cFP-BP- x using the captive screws on the bracket. B. Bolt the rack-mount accessory to a standard 19-in. rack. C. Connect the PE ground terminal on the cFP-BP- x to safety ground. C C A A U U T T I I O O N N Disconnect power before removing the back ...
-
National Instruments cFP-20xx - page 6
6 cFP-20xx Quick Start Guide ni.com I I n n s s t t a a l l l l t t h h e e c c F F P P - - 2 2 0 0 x x x x C C o o n n t t r r o o l l l l e e r r o o n n t t h h e e B B a a c c k k p p l l a a n n e e A. Make sure that no power is connected to the controller or the backplane. B. Make sure that the cFP-20 xx controller is right side up with the N ...
-
National Instruments cFP-20xx - page 7
7 cFP-20xx Quick Start Guide © National Instruments Corporation I I n n s s t t a a l l l l I I / / O O M M o o d d u u l l e e s s o o n n t t h h e e B B a a c c k k p p l l a a n n e e A. Align the captive screws on the I/O module with the holes on the backplane. B. Press firmly to seat the I/O module on the backplane. C. Using a number 2 Phill ...
-
National Instruments cFP-20xx - page 8
8 cFP-20xx Quick Start Guide ni.com I I n n s s t t a a l l l l C C o o n n n n e e c c t t o o r r B B l l o o c c k k s s o o n n t t h h e e B B a a c c k k p p l l a a n n e e In order to connect I/O modules to input signals or to external loads, you need to install a cFP-CB- x connector block or other connectivity accessory for each I/O module ...
-
National Instruments cFP-20xx - page 9
C C o o n n n n e e c c t t t t h h e e c c F F P P - - 2 2 0 0 x x x x t t o o Y Y o o u u r r N N e e t t w w o o r r k k Connect the cFP-20 xx controller to an Ethernet network using the RJ-45 Ethernet port on the controller . Use a standard Category 5 Ethernet cable to connect the cFP-20 xx to an Ethernet hub, or use an Ethernet crossover cable ...
-
National Instruments cFP-20xx - page 10
10 cFP-20xx Quick Start Guide ni.com C. Use a separate power supply for each module that needs external power . D. Refer to the operating instructions for the power requirements of each I/O module. If a module requires external power , connect a power supply to the V and C inputs on the connector block for that module. If you want to power field I/ ...
-
National Instruments cFP-20xx - page 11
I I n n s s t t a a l l l l S S o o f f t t w w a a r r e e o o n n t t h h e e H H o o s s t t P P C C A. Install the software packages you plan to use, such as LabVIEW , LabVIEW RT , Lookout, Measurement Studio, or LabWindows/CVI, before you install the FieldPoint software. The FieldPoint software installation installs the LabVIEW VIs and example ...
-
National Instruments cFP-20xx - page 12
12 cFP-20xx Quick Start Guide ni.com C. Click the + + sign next to I I A A S S e e r r v v e e r r w w i i t t h h O O P P C C in the left pane to expand the view . Right-click F F i i e e l l d d P P o o i i n n t t and select A A d d d d a a c c o o m m m m r r e e s s o o u u r r c c e e t t o o t t h h i i s s s s e e r r v v e e r r . The Comm ...
-
National Instruments cFP-20xx - page 13
G. Enter values on the Network Settings tab of the System Configuration dialog box, shown in the figure at right. If your network does not have a gateway server or DNS server , you should set those parameters to 0.0.0.0. • I I P P A A d d d d r r e e s s s s —The unique, computer-readable address of a device on your network. An IP address is ty ...
-
National Instruments cFP-20xx - page 14
14 cFP-20xx Quick Start Guide ni.com I. Enter an IP address for the T ime Server on the Servers tab of the System Configuration dialog box, shown in the figure at right. The time server is a networked computer that runs the National Instruments T ime Service installed by FieldPoint Explorer . Enter the IP address of the PC you are using. When you f ...
-
National Instruments cFP-20xx - page 15
15 cFP-20xx Quick Start Guide © National Instruments Corporation F F i i n n d d i i n n g g a a n n d d C C o o n n f f i i g g u u r r i i n n g g D D e e v v i i c c e e s s a a n n d d C C h h a a n n n n e e l l s s After you have configured the cFP-20 xx in FieldPoint Explorer , follow these steps to configure Compact FieldPoint devices and ...
-
National Instruments cFP-20xx - page 16
16 cFP-20xx Quick Start Guide ni.com C. T o configure the hardware settings of a particular I/O module, right-click the device name and select E E d d i i t t t t h h i i s s d d e e v v i i c c e e . The Device Configuration dialog box appears, as shown in the figure above. For output modules, you can choose settings for Watchdog Configuration. Re ...
-
National Instruments cFP-20xx - page 17
17 cFP-20xx Quick Start Guide © National Instruments Corporation D. Click C C h h a a n n n n e e l l C C o o n n f f i i g g u u r r a a t t i i o o n n to access the Channel Configuration dialog box, shown in the figure at right. Make your selections in this dialog box as follows: 1. Select the type of channel to show , then select the channel(s ...
-
National Instruments cFP-20xx - page 18
18 cFP-20xx Quick Start Guide ni.com ...
-
National Instruments cFP-20xx - page 19
19 cFP-20xx Quick Start Guide © National Instruments Corporation S S a a v v i i n n g g H H a a r r d d w w a a r r e e C C o o n n f f i i g g u u r r a a t t i i o o n n a a s s P P o o w w e e r r - - U U p p S S t t a a t t e e When you are satisfied with the hardware configuration of the FieldPoint system, you can save this configuration as ...
-
National Instruments cFP-20xx - page 20
20 cFP-20xx Quick Start Guide ni.com S S p p e e c c i i f f i i c c a a t t i i o o n n s s Network Network interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10BaseT and 100BaseTX Ethernet Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IEEE802.3 Communication rates . . . . . . . . . . . . . . . . ...
-
National Instruments cFP-20xx - page 21
21 cFP-20xx Quick Start Guide © National Instruments Corporation Physical Characteristics Screw-terminal wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 16–26 AWG copper conductor wire with 7 mm (0.28 in.) of insulation stripped from the end T orque for screw terminals . . . . . . . . . . . . . . . . . . . . . . 0.5–0.6 N ⋅ m (4.4 ...
-
National Instruments cFP-20xx - page 22
22 cFP-20xx Quick Start Guide ni.com Electromagnetic Compatibility CE, C-T ick, and FCC Part 15 (Class A) Compliant Emissions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 55011 Class A at 10 m FCC Part 15A above 1 GHz Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 61326-1:1997 + A1:1 ...
-
National Instruments cFP-20xx - page 23
ni.com Go to ni.com/support for the most current manuals, examples, and troubleshooting information. For telephone support in the United States, create your service request at ni.com/ask and follow the calling instructions or dial 512 795 8248. For telephone support outside the United States, contact your local branch office: United States 512 683 ...
Haben Sie eine Frage bezüglich National Instruments cFP-20xx?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit National Instruments cFP-20xx nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit National Instruments cFP-20xx hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.