Bedienungsanleitung Western Telematic 12651

16 Seiten 0.15 mb
Download

Zur Seite of 16

Summary
  • Western Telematic 12651 - page 1

    RPB+ Remote Power Boot Switch Preliminary Draft May , 1996 User's Guide ...

  • Western Telematic 12651 - page 2

    ...

  • Western Telematic 12651 - page 3

    1. Introduction Network equipment sometimes "locks-up", making it impossible to communicate. The RPB+ Remote Power Boot Switch can switch AC power on 5 individually controlled plugs, allowing attached equipment to reset (re-boot). ASCII commands are sent to the RS-232 Control Port to select plugs, and specify On, Off, or Boot operations. ...

  • Western Telematic 12651 - page 4

    2. Unit Description 2.1. Front Panel As shown in Figure 1, the RPB+ front panel includes a series of LED indicators which function as follows: À POWER ON: Lights when AC Power is applied to the RPB+. Á DA T A INPUT : Flashes when ASCII commands are received at the Control Port. Â PLUG ON (Plug s1-5 ) : Lights when the corresponding plug is switc ...

  • Western Telematic 12651 - page 5

    2.2. Back Panel As shown in Figure 2, the RPB+ back panel includes the following items: À Switched AC Outlets (Plug s1-5 ) : For connection to up to five AC devices. Each outlet is capable of switching up to 15 Amps. The total for all five outlets must not exceed 15 Amps. Á SetUp Switches (RA TE): A bank of four DIP Switches which set the Control ...

  • Western Telematic 12651 - page 6

    3. Installation 3.1. SetUp Switches The SetUp Switches select the baud rate and Off T ime, and enable/disable the Password feature and Read Only Mode. If switch settings are changed while the unit is powered On, press the Default Button to re-read switches. The Default Button allows the user to change switch settings while power is on, without re-b ...

  • Western Telematic 12651 - page 7

    3.2.1. Connecting to a Modem When connecting directly to an external modem, use a standard A T to Modem cable. Make certain the modem is initialized at the same baud rate as the RPB+ (SetUp Switch 1). The modem must be placed in Auto-Answer mode, and set to answer in one ring. Please refer to the user ’ s guide for your external modem in order to ...

  • Western Telematic 12651 - page 8

    4. Start-Up / Configuration 1. Access the RPB+ Command Mode: The RPB+ is transparent to parity and will accept 7 or 8 bit characters, but will always answer back at 8 bits, no parity . Make certain your communications program (e.g. ProComm) is set for the appropriate baud rate, bits, and parity . It is also recommended to set the communications pro ...

  • Western Telematic 12651 - page 9

    b) Password: T o re-define the password (Default = [Enter] ), key in the new password (up to 8 characters) and press [Enter] . The password can include blank spaces and higher order ASCII characters. Note that the Backspace key will not function during password definition. c) Default (Power-Up Default): Allows the user to define default On/Off cond ...

  • Western Telematic 12651 - page 10

    4.1. The Power-Up Default String The Power-Up Default String allows the user to select default On/Off conditions for each switched AC outlet. When the RPB+ is powered up, or when the /D command (Set Defaults) is invoked, each outlet will be set according to the Default String. Note: · The Power-Up Default String includes five characters; each char ...

  • Western Telematic 12651 - page 11

    5. Operation The device connected to the Control Port must send ASCII characters at the same data rate as the RPB+. The unit accepts 8 bits no parity , or 7 bits even or odd parity , but will always answer back at 8 bits, no parity . Access the RPB+ Command Mode as described in Section 4, Step 1. When the "RPB+>" prompt appears, the us ...

  • Western Telematic 12651 - page 12

    6. Set Plugs to Default: T o set all plugs to the Power-Up Defaults, type /D [Enter] . Note that if the Default String includes missing or invalid characters, the /D command will not function. 7. Exit: T o exit from command mode, type /X [Enter] . Note: When the /n ON/OFF/BOOT command is invoked, the port ( n ) must be specified by number . The Por ...

  • Western Telematic 12651 - page 13

    Appendix A: Specifications Switched Power Plugs: 5 code-selectable AC plugs rated 15 amps max. Each. T otal switched power for all plugs not to exceed 15 amps. Unit initially powers up to ON condition. RS232 Port: DB9 Connector: A 9 Pin Male connector wired in a DTE configuration. Pin Signal I/O Coding: Asynchronous. 7-8 bits, any parity Data Rate: ...

  • Western Telematic 12651 - page 14

    Customer Service Customer Service hours are from 8:00 AM to 5:00 PM, PST , Monday through Friday . When calling, please be prepared to give the name and make of the unit, its serial number and a description of its symptoms. If the unit should need to be returned for factory repair it must be accompanied by a Return Authorization number from Custome ...

  • Western Telematic 12651 - page 15

    ...

  • Western Telematic 12651 - page 16

    · · · · ...

Produzent Western Telematic Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts Western Telematic 12651 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Western Telematic
- Bedienungsanleitungen 12651
- Produktkarten Western Telematic
- Informationsbroschüren
- oder Energieetiketten Western Telematic 12651
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Western Telematic 12651.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Western Telematic 12651, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Western Telematic 12651. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Western Telematic 12651 ansehen.

Die komplette Bedienungsanleitung des Geräts Western Telematic 12651, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Western Telematic 12651 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Western Telematic 12651 verständlich ist.

Eine gänzliche Bedienungsanleitung von Western Telematic sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Western Telematic 12651 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Western Telematic 12651 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Western Telematic 12651, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Western Telematic 12651 - die uns die ersten Schritte während der Nutzung von Western Telematic 12651 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Western Telematic 12651 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Western Telematic 12651 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Western Telematic 12651?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Western Telematic 12651 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Western Telematic 12651 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)