-
Bush Hog 2347 QT - page 1
OPERATION l l MAINTENANCE 1207 $4.00 50057986 M o d e l 2 3 4 7 Q T F r o n t E n d L o a d e r O p e r a t o r ’ s M a n u a l B U S H H O G ® ...
-
Bush Hog 2347 QT - page 2
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as well as ...
-
Bush Hog 2347 QT - page 3
TABLE OF CONTENTS SECTION/PARA PAGE Warranty .....................................................2 Dealer Preparation Check List ....................3 Safety Precautions ......................................4 Federal Laws & Regulations .......................6 I INTRODUCTION & DESCRIPTION ...........7 1-1 Introduction .................... ...
-
Bush Hog 2347 QT - page 4
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog war rants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for comm ...
-
Bush Hog 2347 QT - page 5
DEALER PREPARATION CHECK LIST 2347 QT LOADER BEFORE DELIVERING MACHINE - The following check list should be completed. Use the Operator’s Manual as a guide. o Machine properly assembled. o All safety decals readable. (See decal page) o All bolts tightened to torque specifications given in torque chart. o Machine operates properly. o Customer has ...
-
Bush Hog 2347 QT - page 6
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury. In addition to the design and c ...
-
Bush Hog 2347 QT - page 7
9. Use a piece of cardboard or wood rather than hands and wear eye protection when searching for hydraulic leaks. Escaping hydraulic oil under pressure can penetrate skin. If oil is injected into skin, it must be surgically removed within a few hours by a doctor or gangrene may result. 10. Before disconnecting hydraulic lines, relieve all hydraulic ...
-
Bush Hog 2347 QT - page 8
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-Steige ...
-
Bush Hog 2347 QT - page 9
SECTION I INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your Front End Loader has been carefully designed to give maximum service with minimum down time. This manual is provided to give you the necessary operating and maintenance instructions for keeping your front end loader in top operating con ...
-
Bush Hog 2347 QT - page 10
SERIES LOADER 2347QT A . M a x i m u m L i f t H e i g h t - M e a s u r e d a t P i v o t P i n 1 0 7 i n . B . M a x i m u m L i f t H e i g h t - U n d e r L e v e l B u c k e t 1 0 1 i n . C . C l e a r a n c e w i t h A t t a c h m e n t D u m p e d 4 5 ° 8 2 i n . D . R e a c h a t M a x i m u m H e i g h t 2 2 i n . E . M a x i m u m D u m ...
-
Bush Hog 2347 QT - page 11
SECTION II LOADER MOUNTING AND DISMOUNTING TRACTORS THAT HAVE MOVABLE AXLES MUST BE SET FORWARD IN THE LONG WHEELBASE POSITION AS SHOWN IN FIGURE 2-1 TO PREVENT EXCESSIVE LEVERAGE BEING EXERT- ED ON THE TRACTOR FRAME. FAILURE TO DO SO CAN RESULT IN PERSONAL INJURY AND EQUIPMENT DAMAGE. REFER TO TRACTOR OPERATOR’S MANUAL FOR ABOVE PROCEDURES AND S ...
-
Bush Hog 2347 QT - page 12
USE CAUTION WHEN MOUNTING LOADERS EQUIPPED WITH OPTIONAL CONTROL VALVE ON TRACTORS EQUIPPED WITH CANOPY. RAISING LOADER SUBFRAME TOO HIGH CAN PINCH HAND BETWEEN CONTROL HANDLE AND CANOPY CAUSING INJURY. WARNING D. With tractor at idle speed, carefully activate boom cylinders to raise/lower cross tube until it aligns with front bracket channel. E. D ...
-
Bush Hog 2347 QT - page 13
Figure 2-6 11 Cylinder Mounting Bushing 2-3 DISMOUNTING LOADER Dismount loader on firm, level ground to facilitate the next mounting. It is recommended that loader be stored in a dry place to prevent rusting. A. Observe the position of boom cylinder mount- ing bushing in relation to the subframe. (Figure 2-6) Remember this position to aid in aligni ...
-
Bush Hog 2347 QT - page 14
C. Lower boom until parking stands contact ground. D. Extend bucket cylinders until cutting edge of bucket is frimly on the ground. E. Remove pin from mounting bracket. F. Loosen nut securing cuffs to loader subframe. Remove pin securing cuff. Remove cuff. G. With tractor at idle speed, roll bucket back until subframe raises up off rear bracket. H. ...
-
Bush Hog 2347 QT - page 15
FILLING THE BUCKET Approach and enter the pile with a level bucket. Loaders with 1-lever control, ease lever back and toward you to lift and rollback the bucket. Loaders with 2-lever controls, ease both levers back to lift and rollback the bucket. The lift and rollback of the bucket will increase effi- ciency because... ...a level bucket throughout ...
-
Bush Hog 2347 QT - page 16
CARRYING THE LOAD Position the bucket as low as possible below the level of the tractor hood for maximum stability and visibility, whether the bucket is loaded or empty. Use extreme caution when operating the loader on a slope and keep the bucket as low as possible. This keeps the bucket and tractor center of gravity low and will provide maximum tr ...
-
Bush Hog 2347 QT - page 17
OPERATING WITH FLOAT CONTROL During hard surface operation, keep the bucket level and put the lift control in the float position to permit the bucket to float on the working surface. If hydraulic down pressure is exerted on the bucket, it will wear faster than normal. FLOAT The float will also prevent the mixing of surface material with stockpile m ...
-
Bush Hog 2347 QT - page 18
PEELING AND SCRAPING BACKFILLING 6” Us e a sl igh t buc ket ang le, tr ave l for war d, and hol d the li ft c on tro l fo rw ard to s ta rt t he c ut . Ma ke a sho rt , an gl e cu t a pp rox im ate ly 6” de ep an d b re ak- ou t c lea nl y. With the bucket level, start a cut at the notch approx- imately 2” deep. Hold the depth by feathering t ...
-
Bush Hog 2347 QT - page 19
Leave dirt in the bucket because dumping on each pass wastes time. Operate at right angles to the ditch. Take as big a bite as the tractor can handle without lugging down. DITCH SOIL PILE Leave dirt which drifts over the side of the bucket for final clean-up. Pile dirt on the high side for easier backfilling on a slope. HANDLING LARGE HEAVY OBJECTS ...
-
Bush Hog 2347 QT - page 20
3-4 FORK LIFT OPERATION WARNING TO AVOID SERIOUS INJURY OR DEATH: H H NE VER LIFT LARGE ROUND HAY BALES OR OTHER LOADS ON THE FORK LIFT ATTACHMENT THAT C O U L D R O L L B A C K O N T O T R A C - TOR OPERATOR AREA. H H NE VER USE FORK LIFT ATTACH- MENT TO LIFT OR SUPPORT PEOPLE. H H TRA NSPORT LOADS LOW AND SLOW. H H AV OID CONTACT WITH POWER LINES ...
-
Bush Hog 2347 QT - page 21
SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower machine to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. All bolts should be torqued as recommend- ed in torque chart unless otherwise indicated. BEFORE EACH USE 1 . Inspect hydraulic lines and fit ...
-
Bush Hog 2347 QT - page 22
TABLE 4-1 TROUBLESHOOTING PROCEDURES PROBLEM POSSIBLE CAUSE REMEDY Loader slow and/or will not dump. Hydraulic oil to heavy. Change to proper oil. Oil filter plugged. Clean or replace filter. Hydraulic pump worn. Repair or replace pump. Oil line restricted or leaking. Check all hoses and tubes for leaks, damage or restrictions. Replace damaged or r ...
-
Bush Hog 2347 QT - page 23
SECTION V ASSEMBLY 1. Do not lift heavy parts or assemblies. Use crane, jack, tackle, fork trucks, or other mechanical devices. 2 Select an area for assembly that is clean and free of any debris which might cause persons working on the assembly to trip. 3. Arrange parts to be assembled neatly in the work area and have tools or other mechanical assi ...
-
Bush Hog 2347 QT - page 24
F. Connect hydraulic hoses to loader as shown in Figure 5-3. If optional hydraulic valve is used, refer to paragraphs 5-2 and 5-3 for valve and stand assembly instructions. G. Install cuffs, pins, washers, bolts, and nuts as shown. (Figure 5-4) Figure 5-3 Tractor Hydraulic Kit Straight Adaptor 1/2” NPT to 3/4” JIC 3/4”- 16 JIC Threads (4) Hos ...
-
Bush Hog 2347 QT - page 25
5-2 OPTIONAL HYDRAULIC VALVE STAND ASSEMBLY (Figure 5-5) A. Attach mounting plate to loader frame using two 5/8 x 6-1/2” bolts, flatwashers, lockwashers and nuts. Note that this plate may be rotated 180° to allow three different mounting tube heights. B. Attach mounting bracket to plate using two 1/2 x 1-1/2” bolts, lockwashers and nuts. C. At ...
-
Bush Hog 2347 QT - page 26
5-3 OPTIONAL HYDRAULIC VALVE PLUMBING INSTRUCTIONS D. Remove open center plug. E. Install the closed center plug furnished with valve. Note: When converting to closed center con- figuration open center plug is removed from v alve and installed in sleeve of closed center plug assem- bly. F. Install valve operational decal on valve shield. A. Mount v ...
-
Bush Hog 2347 QT - page 27
IMPORTANT When loader hydraulics are disconnected from tractor hydraulics, hoses A & B must be connected to complete tractor hydraulic circuit. FAILURE TO DO THIS WILL CAUSE SERIOUS DAMAGE TO TRACTOR HYDRAULIC SYSTEM. Power Beyond Plug To Pressurized Return Inlet To Sump Inlet (Use Long Hose Here) To Pressure Inlet B C A These hoses to be furni ...
-
Bush Hog 2347 QT - page 28
Mainframe Eccentric Nut Frame Assembly Long Spear Short Spears 26 5-6 BALE SPEAR OPTION Insert long spear into top of frame and fasten with eccentric nut as shown. Tapered side of nut must be against frame. Torque nut to 470 -505 ft./lbs. Insert short spears into tubes at bottom of frame and tight- en lock bolts. 1/2 X 1-1/2” Bol t 3/8” U-Bolt ...
-
Bush Hog 2347 QT - page 29
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damages can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more infor ...
-
Bush Hog 2347 QT - page 30
B O L T D I A M E T E R W R E N C H ( I N . ) “ B ” A N D S A E S A E S A E S I Z E ( I N . ) “ A ” T H R E A D S I Z E G R A D E 2 G R A D E 5 G R A D E 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37) 9/16 3/8 - 16 UNC 20 (2 ...
-
Bush Hog 2347 QT - page 31
P.O. Box 1039 l l Selma, AL 36702-1039 Telephone (334) 874-2700 l l www.bushhog.com ...
Haben Sie eine Frage bezüglich Bush Hog 2347 QT?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bush Hog 2347 QT nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bush Hog 2347 QT hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.