Deutsch dropdown-ico

Bedienungsanleitung Biostar I945P-A7

38 Seiten 2.85 mb
Download

Zur Seite of 38

Summary
  • Biostar I945P-A7 - page 1

    I945P-A7 i FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These li mits are designed to provide reasonable protection against harmful interference in a residenti al installation. Thi s equi pment generates, uses and can radiate radi ...

  • Biostar I945P-A7 - page 2

    Table of Contents ii Chapter 1: In troducti on .......................................................... 1 1.1 Motherboard Features .......................................................... 1 1.2 Package Che cklist ................................................................ 6 1.3 Layout and Com ponents ....................................... ...

  • Biostar I945P-A7 - page 3

    I945P-A7 1 CHAPTER 1: INTRODUCTION 1.1 M OTHERBOARD F EATURES A. Hardware CPU Supports L G A 775. Supports Intel Pentium 4 processo r up to 3.8GHz. Supports Intel Pentium D p rocessor . Front Side Bus at the following frequency ranges:  533MT/s (133MHz Core Clock)  800MT/s (200MHz Core Clock)  1066MT/s (266MHz Core Clock) Supports Hyper-Th ...

  • Biostar I945P-A7 - page 4

    I945P-A7 2 System Memory Supports dua l channel DDR2 up to 8 banks. Support s DDR2 533 (26 6 MHz) / 667 (333MHz) for a theoretical maximum bandwidth of 10.7 GB/s. Supports 256 -Mb, 512-Mb, or 1G-Mb DDR technolog ies for x8 and x16 devices. Support s non-ECC DIMMs. Maximum DRAM sp ace i s up to 4GB. DIMM Socket Location DDR Module Total Memory Size ...

  • Biostar I945P-A7 - page 5

    I945P-A7 3 Serial ATA Controller integrate d in ICH7 R. Support s Serial A T A 2.0 specification. Dat a transfer rate up to 3GB/s. Support s 4 Serial A T A (SA T A) devices. - Intel Advanced Host Controller (AHCI). - Integrated RAID 0,RAID 1, and RAID 0+1 cap abilities (only for Rev 1.0). On Board High Definition Audio Codec Chip: REAL TEK ALC882. ...

  • Biostar I945P-A7 - page 6

    I945P-A7 4 Internal On-board I/O Connectors and Headers 1 IDE connector support s 2 hard disk devices. 1 front panel header suppo rts front pan el facilities. 1 CD-in connector support s 1 CD-ROM audio-in device. 1 front audio header support s front panel audio-out fun ction. 1 S/PDIF-out conne ctor support s digital audio-out function. 1 S/PDIF-in ...

  • Biostar I945P-A7 - page 7

    I945P-A7 5 6 audio p orts support 8 +2 channels audio-out facilities. (ALC882). C O M 1 PS/2 Keyboard PS/2 Mouse USB x2 Giga LAN USB x2 COM1 Parallel Center/Left Rear Side Line-in Line-out MIC-i n Notice for ALC882 Codec: 1. When connecting audio devic es into audio ports, the audio driver will auto-detect and pop-up the port func tion sel ection w ...

  • Biostar I945P-A7 - page 8

    I945P-A7 6 B. BIOS & Software BIOS Award legal BIOS. Supports APM1.2. Supports ACPI Supports USB Function. Software Support s W arpspeeder™, 9th T ouch™, WINFLASHE R™ an d FLASHER™. 1.2 P ACKAGE C HECKLIST FDD Cable X 1 HDD Cable X 1 User’s Manual X 1 Serial A T A Cable X 1 Fully Setup Driver CD X 1 Rea r I/O Panel for A TX Case X 1 U ...

  • Biostar I945P-A7 - page 9

    I945P-A7 7 1.3 L AYOUT AND C OMPONENTS DDR2_A1 DDR2_A 2 DDR2_B1 DDR2_B 2 FDD1 IDE1 PCI-Ex1_1 (for v1.0) PCI-Ex1_2 (for v1.0) PCI-Ex16 PCI1 PCI2 PCI3 JPANEL1 J1394A 1 (optional) J1394PWR1 (optional) JA TXPWR1 JCF AN1 JAT XPWR2 AUDIO1 (8+2 CH) JAUDIOF1 Super I/O JCI1 JCMOS1 SAT A1 SA T A3 SAT A2 SA T A4 Codec JCDIN1 JSPDI F_OUT 1 JSPDIF_ IN1 (optiona ...

  • Biostar I945P-A7 - page 10

    I945P-A7 8 Pin Cap CHAPTER 2: HARDWARE INSTALLATION 2.1 I NSTALLING C ENTRAL P ROCESS ING U NIT (CPU) CPU1 Codec C O M 1 Step 1: Pull the lever sideways a way from the socket and then raise the lever up to a 90-degree angle. Special Notice: Remove Pin Cap before installation, and make good preservation for future use. Wh en the CPU is removed, cove ...

  • Biostar I945P-A7 - page 11

    I945P-A7 9 Step 2: Look for the black cut edg e on socket, and the white dot on CPU should point forwards this black cut edge. The CPU will fit only in the correct orientation. S tep 2-1: S tep 2-2: Step 3: Hold the CPU do wn firmly , and then close the lever to complete the installation. Step 4: Put the CPU Fan on the CPU a nd buckle it. Connect t ...

  • Biostar I945P-A7 - page 12

    I945P-A7 10 2.2 FAN H EADERS These fan headers support cooling-fan s built in the computer . The fan cable and connector may be different a ccordi ng to the fan manufacturer . Connect the fan cable to the connector while mat ching the black wire to pin#1. JCFAN1: CPU Fan Header Pin Assignment 1 Ground 2 Power 3 FAN RPM rate sense 14 JCF AN1 Code c ...

  • Biostar I945P-A7 - page 13

    I945P-A7 11 2.3 I NSTALLING S YSTEM M EMORY DDR2_A1 DDR2_A2 DDR2_B1 DDR2_B2 Codec C O M 1 1. Unlock a DIMM slot by pressing the ret aining clip s outward. Align a DIMM on the slot such that the not ch on the DIMM ma tches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retainin g chip snap back in place an d ...

  • Biostar I945P-A7 - page 14

    I945P-A7 12 2.4 C ONNECTORS AND S LOTS FDD1: Floppy Disk Connector The motherboard provides a st andard floppy disk connector that supports 36 0 K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector su ppo rts the provide d floppy drive rib bon cables. 1 2 34 33 Code c C O M 1 IDE1: Hard Disk Connector (IDE2 and IDE3 are optional.) The m ...

  • Biostar I945P-A7 - page 15

    I945P-A7 13 PCI-Ex16: PCI-Express x16 Slot - PCI-Express 1.0a compliant. - Maximum theoretical realized bandwid th of 4GB/s simultaneousl y per direction, for an aggregate of 8GB /s totally . PCI-Ex1_1/PCI-Ex1_2: PCI-Express x1 slots (Only for Rev 1.0) - PCI-Express 1.0a compliant. - Data transfer band width up to 250MB/s per di rection; 500MB/s in ...

  • Biostar I945P-A7 - page 16

    I945P-A7 14 PCI1~PCI3: Peripheral Component Interconnect Slots This motherboard is equip ped with 3 st andard PCI slo t s. PCI st and s for Peripheral Component Interconnect, and it is a bu s st andard for expansion cards. This PCI slot is desig nated as 32 bit s. PCI3 PCI2 PCI1 Code c C O M 1 ...

  • Biostar I945P-A7 - page 17

    I945P-A7 15 CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 H OW TO S ETUP J UMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened Pin closed Pin1-2 closed 3.2 D ETAIL S ET TINGS JATXPWR1: ATX Po wer Connector This connector allows us ...

  • Biostar I945P-A7 - page 18

    I945P-A7 16 JATXPWR2: ATX Po wer Connector By connecting this connector , it will provide +12V to CPU power circuit. Pin Assignment 1 +12V 2 +12V 3 Ground 3 4 1 2 Code c C O M 1 4 Ground JSPDIF_OUT 1: Digital Audio- out Connector This connector allows user to connect the PCI bracket SPDIF output hea der. Pin Assignment 1 +5V 2 SPDIF_OUT 1 3 Code c ...

  • Biostar I945P-A7 - page 19

    I945P-A7 17 J1394A1 (o pt ional): Hea d er for 1 394 Firewire Port at Front Panel Pin Assignment 1 A+ 2 A- 3 Ground 4 Ground 5 B+ 6 B- 7 +12V 8 +12V 9 Key 1 2 9 10 Code c C O M 1 10 Ground J1394PWR1 (opt iona l): Power So urce for 1394 Firewire Port This header allows user to connect the digital image device, like DV , D8, or V8, etc. 1 3 Pin 1-2 C ...

  • Biostar I945P-A7 - page 20

    I945P-A7 18 4 Right channel input ...

  • Biostar I945P-A7 - page 21

    I945P-A7 19 JAUDIOF1: F ront Panel Au dio Header This header allo ws user to connect the front audio o utput cable with the PC front panel. It will disable the output on back panel audio connectors. With High Definition A udio Codec: ALC882 Pin Assignment 1 Mic (L) 2 Ground 3 Mic (R) 4 PRESENCE 5 Headphone (R) 6 Jack 1 SENSE 7 Jack Detection 8 Conn ...

  • Biostar I945P-A7 - page 22

    I945P-A7 20 JKBV1: Power Source Header fo r PS/2 Keyboard and Mouse 1 3 Pin 1-2 Cl ose +5V for PS/2 key board and mouse. 1 3 Code c C O M 1 1 3 Pin 2-3 c lose PS/2 keyboard and mouse are powered by +5V st andby voltage. Note: In order to support this function “Power-on system via keyboard and mouse”, “JKBV1” jumper cap should be placed on P ...

  • Biostar I945P-A7 - page 23

    I945P-A7 21 SATA1~SATA4: Seri al ATA Co nnect ors The motherboard has a PCI to SA T A Controller w ith 4 channels SA T A interface, it satisfies the SA T A 2.0 spec and with transfer rate of 3Gb/s. Pin Assignment 1 Ground 2 TX+ 3 TX- 4 Ground 5 RX- 6 RX+ SA TA4 SA TA1 SA TA2 SA TA3 1 7 4 Code c C O M 1 7 Ground JPANEL1: Fr ont Panel Hea der This 24 ...

  • Biostar I945P-A7 - page 24

    I945P-A7 22 JCMOS1: Clear CMOS Header By placing the jumper on pin2-3, it allo ws user to restore the BIOS safe setting and the CMOS data, please carefully follow the proced ures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 3 Code c C O M 1 1 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. Remo ...

  • Biostar I945P-A7 - page 25

    I945P-A7 23 CHAPTER 4: USEFUL HELP 4.1 A WARD BIOS B EEP C ODE Beep Sound Meaning One long beep followed by t wo short beeps Video card not found or video card memory bad High-low siren soun d CPU overheated System will shut down automatically One Short beep when system boot-up No error found during POST Long beeps every other seco nd No DRAM detec ...

  • Biostar I945P-A7 - page 26

    I945P-A7 24 B. CPU Overheated If the system shutdown aut omatically aft er po wer on system for seconds, that means the CPU prot e ction function ha s been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double che ck: 1. Th ...

  • Biostar I945P-A7 - page 27

    I945P-A7 25 4.3 T ROUBLESHOOTING Probable Solution 1. No power to the system at all Power light don’t illuminate, fan inside power supply does not turn on. 2. Indicator light on keyboard does not turn on. 1. Make sure power cable is securely plugged in. 2. Replace cable. 3. Contact technical support. System inoperative. Keyboard lig hts are on, p ...

  • Biostar I945P-A7 - page 28

    I945P-A7 26 CHAPTER 5: DUAL VIDEO FUNCTION Note: Dual Video Function is only for Rev 1.0. 5.1 R EQUIREMENT S Only Windows XP supp orts Dual V ideo function. T wo identical graphics cards that are NVIDIA certified. The graphics card driver should support NVIDIA SLI technology . The power supply unit must provide at least the minimum power required b ...

  • Biostar I945P-A7 - page 29

    I945P-A7 27 F r o n t v i e w S i d e v i e w S tep 5: T o securely fix the connector between two graphics cards, a retention bracket must be inst alled. S tep 5-1: Remove any of the brac ket cover between the two graphics cards. S tep 5-2: Align and insert the retention b racket into th e slot and the n fix it with a screw . Notice: 1. Make sure t ...

  • Biostar I945P-A7 - page 30

    I945P-A7 28 CHAPTER 6: WARPSPEEDER™ 6.1 I NTRODUCTION [W arpS peeder™], a new powerful co ntrol utility , features three user-friendly functions inclu ding Overclock Manager , Overvolt age Manager , and Hardware Monitor . With the Overclock Manager , users can easily adjust the frequency they prefer or they can get the best CPU perf ormance wit ...

  • Biostar I945P-A7 - page 31

    I945P-A7 29 6.3 I NSTALLATION 1. Execute the setup execution file, and the n the following dialo g will pop up. Please click “Next” button and follow the default proce dure to install. 2. When you see the following dialog in setup pro ced ure, it means setup is completed. If the “Launch the W arpS peeder T ray Utility” checkbox is checked, ...

  • Biostar I945P-A7 - page 32

    I945P-A7 30 6.4 [W ARP S PEEDER ™] INCLUDES 1 TRAY ICON AND 5 PANELS 1. Tray Icon: Whenever the T ray Icon utility is l aunched, it will display a little tray icon on the right side of Windows T askb ar . This utility is responsible for conveniently invoking [W arpS peeder™] Utility . Y ou can use the mo use by clicking the left button in order ...

  • Biostar I945P-A7 - page 33

    I945P-A7 31 2. Main Panel If you click the tray icon, [W ar pS peeder™] utility will be invoked. Please refer to the following figure; the utility’ s first window you will see is Main Panel. Main Panel contains features as follows: a. Display the CPU S pee d, CPU external cloc k, Memory clock, AGP clock, and PCI clock information. b. Cont ain s ...

  • Biostar I945P-A7 - page 34

    I945P-A7 32 3. Voltage Panel Click the V oltage button in Main Panel, the button will be highlighte d and the V oltage Panel will slide out to up as the following figure. In this panel, you can decide to increa se CPU core voltage a nd Memory voltage or not. The default setting is “No”. If you want to get the best performance of overclockin g, ...

  • Biostar I945P-A7 - page 35

    I945P-A7 33 4. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to lef t as the following figure. Overclock Panel contains the these features: a. “–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3 MHz button”: provide user the ability to do real-ti ...

  • Biostar I945P-A7 - page 36

    I945P-A7 34 c. “Auto-overclock button”: Us er can click this button and [W arpS peeder™] will set the best and st able pe rformance and frequency automatically . [W arpS peeder™] utility will execute a series of testing until system fail. Then system will do fail-safe reboot by using W atchdog function. After reboot, the [W arpS peeder™] ...

  • Biostar I945P-A7 - page 37

    I945P-A7 35 6. About Panel Click the “about” button in Main Panel, the button will be highlig hted and the About Panel will slide out to up as the following figure. In this panel, you can get model name and det ail information in hint s of all the chipset that are related to overclocking. Y ou can also get the mainboard’s BIOS mo del and the ...

  • Biostar I945P-A7 - page 38

    I945P-A7 36 Note: Because the overclock, overvolt ag e, and hardware monitor featu re s are controlled by several separate chip set, [W arpS peeder™] divide these features to separate panels. If one chip set is not on board, the correlative button in Main p anel will be di sabled, but will not interfere other panels’ functions. Thi s pro pe rty ...

Produzent Biostar Kategorie Motherboard

Dokumente, die wir vom Produzenten des Geräts Biostar I945P-A7 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Biostar
- Bedienungsanleitungen I945P-A7
- Produktkarten Biostar
- Informationsbroschüren
- oder Energieetiketten Biostar I945P-A7
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Biostar I945P-A7.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Biostar I945P-A7, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Biostar I945P-A7. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Biostar I945P-A7 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Biostar I945P-A7, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Biostar I945P-A7 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Biostar I945P-A7 verständlich ist.

Eine gänzliche Bedienungsanleitung von Biostar sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Biostar I945P-A7 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Biostar I945P-A7 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Biostar I945P-A7, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Biostar I945P-A7 - die uns die ersten Schritte während der Nutzung von Biostar I945P-A7 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Biostar I945P-A7 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Biostar I945P-A7 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Biostar I945P-A7?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Biostar I945P-A7 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Biostar I945P-A7 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)