Deutsch dropdown-ico

Bedienungsanleitung Cisco Systems AIRSAP1602IAK95

38 Seiten 1.31 mb
Download

Zur Seite of 38

Summary
  • Cisco Systems AIRSAP1602IAK95 - page 1

    G ETTING S TARTED G UIDE Cisco Aironet 1600 Series Access Points December , 2012 Revised: April 1 6, 2013 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructi ons 4 Unpacking 5 Configuratio ns 6 Access Point Ports and Connectors 7 Configuring the Access Point 8 Mounting the Access Point 9 Deploying the Access Poin t on the Wirel ...

  • Cisco Systems AIRSAP1602IAK95 - page 2

    2 1 About this Guide This Guide provides in structions on how to inst all and configure your Cisco Aironet 1600 Series Access Point. The 1600 Series Ac cess Point is referred to as the 160 0 series or the acce ss point in this document. 2 Introduction to the Access Point The 1600 series offers dual-band ra dios (2.4 GHz and 5 GHz) with in tegrated ...

  • Cisco Systems AIRSAP1602IAK95 - page 3

    3 • 802.11af/at – CDP (Cisco Discovery Protocol) • 2.4 GHz and 5 GHz 802.11n radios with the following features: – 3TX x 3RX – 2 spatial streams, 300 Mbps PHY rate – DPD (Digital Pre-Distortion) technology – Radio hardware is capable of explicit comp ressed beamforming (ECBF) per 802.11n standard 3 Safety Instructions T ranslated vers ...

  • Cisco Systems AIRSAP1602IAK95 - page 4

    4 War n in g Do not operate your wirel ess network device near u nshielded blasting caps or in an explosive environment unless the device has been mod ified to be especially qualified for such use. Statement 245B War n in g In order to comply wi th FCC radio frequency (RF) exposure limits, an tennas should be located at a minimum of 7.9 inches (20 ...

  • Cisco Systems AIRSAP1602IAK95 - page 5

    5 Step 3 V erify that you have rece ived the items listed below . If any item is missing or damaged, contact your Cisco representative or reseller for instructions. – The access point – Mounting bracket (optional; selected when you ordered the acce ss point) – Adjustable ceiling-rail clip (optional; se lected when you ordered the access point ...

  • Cisco Systems AIRSAP1602IAK95 - page 6

    6 Internal Antennas The 1602I model access p oints are configured with up to three dual-band inverted-F antennas and two 2.4-GHz/5-GHz dual-band radios. Each antenna covers both the 2.4 GHz and the 5 GHz bands with a single feed line. The basic features are as follows: • Dual-band inverted-F antenna for use in both th e 2.4-GHz and 5-GHz bands. ? ...

  • Cisco Systems AIRSAP1602IAK95 - page 7

    7 Figur e 1 Access P oint Por ts and Connections (t op) 1 Antenna connector A 3 Antenna connector C 2 Antenna connector B ...

  • Cisco Systems AIRSAP1602IAK95 - page 8

    8 Figur e 2 Access P oint LED Indicator (top) The ports and connections on the bottom of the access point are shown in Figure 3 . Figur e 3 Access P oint Por ts and Connections (bot tom) 1 LED indicator 1 272377 2 3 4 1 5 6 6 ...

  • Cisco Systems AIRSAP1602IAK95 - page 9

    9 7 Configuring the Access Point This section describes how to connect the access point to a wireless LAN controller . Because the configuration process takes plac e on the controller , see the Cisco Wireless LAN Controller Configuration Guide for additional information. This gu ide is available on Cisco.com. Note Cloud-enabled access points look f ...

  • Cisco Systems AIRSAP1602IAK95 - page 10

    10 Note CAPW A P support is provided in controller so ftware release 5.2 or later . However , your controller mu st be runn ing release 7.4.x. x or later to su pport 1600 series access points. Note Y ou cannot edit or query any ac cess poin t using the controller C LI if the name of the access point contains a space. Note Make sure that the control ...

  • Cisco Systems AIRSAP1602IAK95 - page 11

    11 Preparing the Access Point Before you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool) to determine the be st location to install your access point. Y ou should have the follow ing information about y our wireless network available: • Access point locations. • Access point mounti ...

  • Cisco Systems AIRSAP1602IAK95 - page 12

    12 Performing a Pre-Instal lation Configuration The following procedures ensure th at your access point installati on and initial op eration go as expected. A pre-installation configuration is also known as priming the access point . This procedure is optional. Note Performing a pre-installation configuration is an opti onal procedure. If your netw ...

  • Cisco Systems AIRSAP1602IAK95 - page 13

    13 Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco Prime Infrastructure procedures as described in the appropriate Cisco wireless LAN controller guide. a. Make sure that access points have Layer 3 conne ctivity to the Cisco wireless LAN controller Management I ...

  • Cisco Systems AIRSAP1602IAK95 - page 14

    14 Note If the access point remains in this mode for more than five minutes, the access point is unable to find the Master Cisc o wireless LAN contro ller. Check the connection betwee n the access point and the Cisco wirele ss LAN controller and be sure that they are on the same subnet. c. If the access point shuts down, check the power source. d. ...

  • Cisco Systems AIRSAP1602IAK95 - page 15

    15 8 Mounting the Access Point Cisco Aironet 1600 series access points can be mo unted in severa l configurations, including on a suspended ceiling, on a hard ceiling or wall , on an electrical or n etwork box, and above a su spended ceiling. Click this URL to browse to comp lete access point mounting instructions: http://www.cisco.com/en/US/docs/w ...

  • Cisco Systems AIRSAP1602IAK95 - page 16

    16 10 Troubleshooting If you experience difficulty getti ng your access point installed and running, lo ok for a solution to your problem in this guide or in additional access po int documentation. These, and other documents, are available on Cisco.com. Guidelines for Using Cisco Ai ronet Lightweigh t Access Points Keep these guidelines in mind whe ...

  • Cisco Systems AIRSAP1602IAK95 - page 17

    17 Figur e 5 Access P oint LED Location The access point status LED indicates va rious conditions and are described in Table 1 . 1 Status LED T a ble 1 LED Status Indicati ons Message Ty p e Status LED Message Meaning Boot loader status sequence Blinking green DRAM memory test in progress DRAM memory test OK Board initialization in progress Initial ...

  • Cisco Systems AIRSAP1602IAK95 - page 18

    18 Troubleshooting the Ac cess Point Join Process Access points can fail to join a controller for many reasons: a R ADIUS auth orization is pending; self-signed certificat es are not enabled on the cont roller; the access point’ s and controller’ s regulatory domains don’ t match, a nd so on. Operating status Blinking amber Software upgrade i ...

  • Cisco Systems AIRSAP1602IAK95 - page 19

    19 Controller software enables you to configure the a cce ss points to send all CAPW AP-related errors to a syslog server . Y ou do not need to enable any de bug command s on the controller because all of the CAPW A P error messages ca n be viewed from the syslog server itself. The state of the access point is not maintained on the controller u nti ...

  • Cisco Systems AIRSAP1602IAK95 - page 20

    20 Y ou can configure the syslog server for access points and view th e access point join information only from the controller CLI. A detailed explanation of th e join process is on Cisco.com at the following URL: http://www.Cisco.com/en/US/products/ps6366/products_tech_note09 186a00808f8599.shtml 11 Declarations of Conformity and Regulatory Inform ...

  • Cisco Systems AIRSAP1602IAK95 - page 21

    21 This device complies with Part 15 rules. Operation is subject to the followin g two conditions: 1. This device may not cause harmful interferenc e, and 2. This device must accept any interference received, incl uding interference that may cause undesired operation. This device operates in the 5150-5250MHz and 54 70-5725MH z bands and is therefor ...

  • Cisco Systems AIRSAP1602IAK95 - page 22

    22 VCCI Statement for Japan War n in g This is a Class B product based on the standard of the V oluntary Control Council for Interf erence from Information T echnology Equipment (VCCI). If thi s is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the inst ...

  • Cisco Systems AIRSAP1602IAK95 - page 23

    23 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interf erence when operating Cisc o Aironet access points in Japan. These guidelines are p rovided in both Japanese and English. Japanese Translation English Translation This equipment operates in the same frequency band width as industria ...

  • Cisco Systems AIRSAP1602IAK95 - page 24

    24 Statement 371—Power Cable and AC Adapter English Translation When installing th e product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the ? ...

  • Cisco Systems AIRSAP1602IAK95 - page 25

    25 This device complies with Class B Limits of Industry Canada. Operatio n is subject to the follo wing two conditions: 1. This device may not cause harmful interferenc e, and 2. This device must accept any interference received, incl uding interference that may cause undesired operation. Cisco Aironet Access Points are cert ified to the requiremen ...

  • Cisco Systems AIRSAP1602IAK95 - page 26

    26 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC ...

  • Cisco Systems AIRSAP1602IAK95 - page 27

    27 The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure ref e rred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed. ...

  • Cisco Systems AIRSAP1602IAK95 - page 28

    28 This device also conforms to the EMC requirem ents of the Medical Devices Directi ve 93/42/EEC. Note This equipment is intended to be used in a ll EU and EF T A co untries. Outdoor use may be restricted to certain frequencie s and/or may require a license fo r operation. For more details, contact Cisco Corporate Compliance. For 1600 series acces ...

  • Cisco Systems AIRSAP1602IAK95 - page 29

    29 As such the systems are desi gned to be operated as to avoid contact with the antennas by the end user . It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of th e user o ...

  • Cisco Systems AIRSAP1602IAK95 - page 30

    30 This Device Meets the In dustry Canada Guidelines for Exposure to Radio Waves The 1600 series device includes a radio transmi tter an d receiver . It is designed not to exceed the limits for exposure to radio waves (radio frequency electrom agnetic fields) as referenced in Heal th Canada Safety Code 6. The guidelines include a substantial safe t ...

  • Cisco Systems AIRSAP1602IAK95 - page 31

    31 • United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk • Cellular T elecommunications Association at this U RL: www.wow-com.com • The Mobile Manufacturers Forum a t this URL: www.mmfai.org Administrative Rules for Cisco Ai ronet Access Points in Taiwan This section provides administrative rules for oper ating ...

  • Cisco Systems AIRSAP1602IAK95 - page 32

    32 English Translation Administrative Rules for Low- power Radio-Frequency Devices Article 12 For those low-power radio-frequenc y devices that have alr e ady recei ved a type -approval , compani es, business units or users should not change its freque ncies, increase its power or change its original features and functions. Article 14 The operation ...

  • Cisco Systems AIRSAP1602IAK95 - page 33

    33 English Translation Low-power Radio-frequency Devices T echn ical Specifications Operation of Cisco Aironet Access Points in Brazil This section contains special information for oper ation of Cisco Aironet access points in Brazil. Access Point Models AIR-SAP1602I-E-K9 AIR-SAP1602E-E-K9 AIR-CAP1602I-E-K9 AIR-CAP1602E-E-K9 AIR-CLD1602I-E-K9 Regula ...

  • Cisco Systems AIRSAP1602IAK95 - page 34

    Figur e 6 Brazil Regulat ory Inf ormation Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e nã o po de causar interferência a sistemas operando em caráter primário. English Translation This equipment operates on a ...

  • Cisco Systems AIRSAP1602IAK95 - page 35

    35 12 Access Point Specifications Table 2 lists the technical speci fications for 1600 series acc ess points. T able 2 A ccess Point Specifications Category Specification Dimensions (LxWxD) 8.68 x 8.68 x 1.84 in. (22.04 x 22.0 4 x 4.67 cm) W eight 1.9 lbs (0.86 kg) Operating temperatures AP1602E: -4 to 122 degrees F (-20 to 50 degrees C) AP1602I: 3 ...

  • Cisco Systems AIRSAP1602IAK95 - page 36

    36 13 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitti ng a service request, and gathering additional information, see the monthly What’ s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation, at: http://www .cisco.com/en/US/docs/genera ...

  • Cisco Systems AIRSAP1602IAK95 - page 37

    37 ...

  • Cisco Systems AIRSAP1602IAK95 - page 38

    Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco .com/go/trademarks . Third-party trad emarks mentioned are the p roperty of their respec tive owners. The use of th e word partn er does not i m ply a partners ...

Produzent Cisco Systems Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts Cisco Systems AIRSAP1602IAK95 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco Systems
- Bedienungsanleitungen AIRSAP1602IAK95
- Produktkarten Cisco Systems
- Informationsbroschüren
- oder Energieetiketten Cisco Systems AIRSAP1602IAK95
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Systems AIRSAP1602IAK95.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Systems AIRSAP1602IAK95, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Systems AIRSAP1602IAK95. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Systems AIRSAP1602IAK95 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Systems AIRSAP1602IAK95, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Systems AIRSAP1602IAK95 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Systems AIRSAP1602IAK95 verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Systems AIRSAP1602IAK95 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Systems AIRSAP1602IAK95 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Systems AIRSAP1602IAK95, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Systems AIRSAP1602IAK95 - die uns die ersten Schritte während der Nutzung von Cisco Systems AIRSAP1602IAK95 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Systems AIRSAP1602IAK95 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Systems AIRSAP1602IAK95 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Systems AIRSAP1602IAK95?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Systems AIRSAP1602IAK95 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Systems AIRSAP1602IAK95 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)