Bedienungsanleitung Schneider Electric EM4000

44 Seiten 3.22 mb
Download

Zur Seite of 44

Summary
  • Schneider Electric EM4000 - page 1

    PowerLogic TM Series EM4000 High-Density Meter Inst allation Guide 930-134-01-A.00 11/2013 ...

  • Schneider Electric EM4000 - page 2

    ...

  • Schneider Electric EM4000 - page 3

    Safety Information Important Information Read these instructions carefully and look at the equipment to become familiar with the d evice before trying to install , operate, service o r maintain it. The following special messages may appe ar throughout this manual or on the equipment to warn of poten tial hazards or to call attention to information ...

  • Schneider Electric EM4000 - page 4

    Notices FCC Part 15 Notice This equipment has be en tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of th e FCC Rules. These limits are designed to provide reasonable protection against harmful in terference in a residential installation. This equipment gen erates, uses, and can radiate ra dio frequency ...

  • Schneider Electric EM4000 - page 5

    telephone company will notify you as soon as possible. You will also be advised of your right to file a complaint with th e FCC if you believe it is necessary. The telephone company may ma ke changes in its facilitie s, equipment, operations or procedures that could affect the oper at ion of this equipment. If this happens, the telephone company wi ...

  • Schneider Electric EM4000 - page 6

    ...

  • Schneider Electric EM4000 - page 7

    930-134-01-A.00 PowerLogic TM EM4000 Series 11/2013 Table of Con tents ©2013 Schneider Electric All Rights Reserved i Table of Contents Introduction ........... ................ ................ ............. ................ ............ 1 System Description ....... ................ ................ ............. ............... 1 PowerLogic EM40 ...

  • Schneider Electric EM4000 - page 8

    PowerLogic TM EM4000 Series 930-134-01-A.00 Table of Contents 11/2013 ©2013 Schneider Electric All Rights Reserved ii ...

  • Schneider Electric EM4000 - page 9

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 1 Introduction This document describes the PowerLog ic EM4033 and EM4080 meters , including procedures to install an d start up t he uni t, and complete the in itial configuration: • “System Description” on page 1 • “Pre-In ...

  • Schneider Electric EM4000 - page 10

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 2 ©2013 Schneider Electric All Rights Reserved Table 1: PowerLogic EM4000 series meter specifications Specification PowerLogic EM4033 meter PowerLogic EM4080 meter Dimensions Height: 13.125 in. (33.5 cm) Width: 12 in. (30.5 cm) Depth: 2.125 in. (5.5 cm) Height: 13.125 in. (33.5 ...

  • Schneider Electric EM4000 - page 11

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 3 Front Panel Display The PowerLogic EM4033 and EM40 80 meters have the following front panel features (Figure 1 shows the Powe rLogic EM4080 front panel): • LCD — displays 2 rows of 16 characters for each of the meter points (8, ...

  • Schneider Electric EM4000 - page 12

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 4 ©2013 Schneider Electric All Rights Reserved Figure 2 s hows the int ernal view of thePowerLo gic EM4033 and EM408 0 meters. Figure 2: PowerLogic EM403 3 and PowerLogic EM4080 internal view 1 4 1 6 7 8 10 11 12 13 5 1 1 2 9 15 14 17 16 3 Legend: 1 Cov er screw location 2 Mete ...

  • Schneider Electric EM4000 - page 13

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 5 Safety Precautions Carefully observe these safet y instructions. Electrical Standards Compliance • Use the unit only in accordance with the electrical power rating • The unit is only to be installe d by a qualifie d electrician ...

  • Schneider Electric EM4000 - page 14

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 6 ©2013 Schneider Electric All Rights Reserved Installation This section contains the following installatio n topics: • “Pre-Installation” on pa ge 6 • “Installation Procedures” on page 7 • “Connec ting Pulse Inputs” on pa ge 26 Pre-Installation The pre-instal ...

  • Schneider Electric EM4000 - page 15

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 7 3. Determine the number an d types of meters or monitors required (single- phase, network, or three-ph ase). 4. Determine the model numbe r and correct sense voltage based on the vo ltage label on the top right side of the unit. Ac ...

  • Schneider Electric EM4000 - page 16

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 8 ©2013 Schneider Electric All Rights Reserved Figure 3: 120V Mounting Layout , Dimensions and Clearances 6.0 in 15.2cm 11.0 in 27.9 cm (EM4033) 10.67 in 27.1cm 4.0 in 10.2 cm 1 2 2 1 2 2 1 1 3 4 4 6 5 7 8 9 8 Legend: 1. Mounting keyhole 2. Cov er screw location 3. Electrical d ...

  • Schneider Electric EM4000 - page 17

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 9 Installing Potential Transformers for Th ree-Phase Service Greater Than 277V Potential transformers ar e required when me tering services greater th an the rated voltage input of the meter. Potential tr ansformers are used to reduc ...

  • Schneider Electric EM4000 - page 18

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 10 ©2013 Schneider Electric All Rights Reserved Figure 4: Typical three-pha se 347V installation H1 X1 H2 X2 H1 X1 H2 X2 H1 X1 H2 X2 C B A N C B A N 1 2 3 4 11 Z 5 6 7 8 13 11 12 Shor ting block detail 10 9 Legend: 1 Shorting block enclosure 2 Shorting block 3 Distribution pane ...

  • Schneider Electric EM4000 - page 19

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 11 Installing the Sense Voltage and Control Voltag e Cables in Wye and Delta Services The sense voltage (A, B, C, N) provides phase voltages for me tering. The configuration depends o n the type of service being metered: • see “F ...

  • Schneider Electric EM4000 - page 20

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 12 ©2013 Schneider Electric All Rights Reserved To install the control voltage cable in a 208Y/120V or 1 20/240V application: NOTE: If the circuit breaker panel does no t designate ph ase A, phase B and phase C feeds, make your own designation and us e it for the rest of the in ...

  • Schneider Electric EM4000 - page 21

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 13 For a single-phase panel with the 1 20V variant of the meter: • Connect meter terminal A to the voltage disconnect phase A (red wire) • Connect meter terminal B to the voltage disconnect phase B (black wire) • Connect meter ...

  • Schneider Electric EM4000 - page 22

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 14 ©2013 Schneider Electric All Rights Reserved For a 208Y /120V three- phase wye p anel with th e 120V varian t of the m eter: • Connect meter termin al A to the volta ge disconnec t phase A (r ed wire) • Connect meter terminal B to the voltage di sconnect phase B (black w ...

  • Schneider Electric EM4000 - page 23

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 15 For a 480Y/277V three-phas e wye panel with the 277V variant of the meter: • Connect meter terminal A to the voltage disconnect phase A (red wire) • Connect meter terminal B to the voltage disconnect phase B (black wire) • C ...

  • Schneider Electric EM4000 - page 24

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 16 ©2013 Schneider Electric All Rights Reserved For a 600Y/347V or higher t hree-phase wye panel with potential tran sformers with the 120V variant of the met er: • Connect meter termin al A to the volta ge disconnec t phase A (r ed wire) • Connect meter terminal B to the v ...

  • Schneider Electric EM4000 - page 25

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 17 Delta service metering To use the PowerLogic EM4000 mete r in a Delta service, the line-to-line voltage from the Delta service must be reduced to 120V line-to- line using appropriate potential transformers. Metering a Delta se rvi ...

  • Schneider Electric EM4000 - page 26

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 18 ©2013 Schneider Electric All Rights Reserved Installing the Current Tra nsformers The two models of PowerLog ic EM4000 me ter use curr ent transformers (CTs) with different secondary outputs. The Power Log ic EM4033 meter uses split-core 0.33 3V CTs (see Figure 10 ), and the ...

  • Schneider Electric EM4000 - page 27

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 19 Figure 10: PowerLogic EM4033 split-core 0.333V curre nt transformer 3 1 2 T H IS SI D E T OWAR DS S O UR C E 4 5 Legend: 1 Source 2 Energy ow 3 Load 4 X1 5 X2 DANGER ...

  • Schneider Electric EM4000 - page 28

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 20 ©2013 Schneider Electric All Rights Reserved Figure 11: PowerLogic EM4080 mA current tran sformer Installing the CTs on the PowerLogic EM4033 an d PowerLogic EM4080 Do not apply power until you have made th ese connections and followed all of the instructions below: • Conn ...

  • Schneider Electric EM4000 - page 29

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 21 1. Connect the 50-pin connecto r to the PowerLogic connector located at the bottom side of the unit, and secu re it in place with the retaining clips. 2. Feed the free end of the cable through the bottom left of the mete r enclosu ...

  • Schneider Electric EM4000 - page 30

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 22 ©2013 Schneider Electric All Rights Reserved To connect the 5A CT to the converter on the PowerLogic EM40 80, follow these steps: 1. Connect the X1 lead of the 5A CT to the shorting device. 2. Connect the X2 lead of the 5A CT to the shorting device. 3. Connect the X1 lead (r ...

  • Schneider Electric EM4000 - page 31

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 23 Figure 12: PowerLogic EM4080 5A CT connection to converter 7 6 8 11 3 4 1 2 5 10 12 9 Legend: 1 Shor ting block 2 X2 3 Energy ow 4 5A C T 5 X1 6 Red (X1) 7 5A Con ver ter 8 X1 to 25-pair cable 9 X2 to 25-pair cable 10 Enclosure ...

  • Schneider Electric EM4000 - page 32

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 24 ©2013 Schneider Electric All Rights Reserved Table 2: PowerLogic EM4000 meter CT color pair identification 1-phase, 24 meter points Network- or 1-phase, 12 met er points 3-phase, 8 meter points Meter point ID (meter point #- probe #) Connect X1 CT lead to: Connect X2 CT lead ...

  • Schneider Electric EM4000 - page 33

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 25 Connecting the Communications Connections for communication s using the Ethernet port or Modbus RTU port are described in this section. Connecting the Ethernet Cable If the Ethernet port is used to report dat a, an RJ45 patch cabl ...

  • Schneider Electric EM4000 - page 34

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 26 ©2013 Schneider Electric All Rights Reserved Connecting Pulse Inputs Each PowerLogic meter has two pulse inputs that can be used to count and repor t pulses gene rated by another meter (pulsing device). Connect the output of the pulsing device to one of the two puls e input ...

  • Schneider Electric EM4000 - page 35

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 27 Display Navigation The PowerLogic EM4000 mete r has three buttons to control the information presented on the LCD. The display has a normal and a dia gnostics mode. The PowerLogic EM4000 meter starts in nor mal mode, an d enters d ...

  • Schneider Electric EM4000 - page 36

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 28 ©2013 Schneider Electric All Rights Reserved • Default gateway • PPP user name • Phone number • AT command string • Alternate phone number • Unit serial number • Firmwar e build number • Ethernet port MAC ad dress • Firmwar e revision • Potential transfor ...

  • Schneider Electric EM4000 - page 37

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 29 Figure 14: Installa tion Record (sample shown) ...

  • Schneider Electric EM4000 - page 38

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 30 ©2013 Schneider Electric All Rights Reserved Maintenance Do not perform any operation or mainten ance pr ocedures that are not described in this product documentation. Visually i nspect the equipm ent yearly and ensure it is free of dust or other particles. If nece ssary, wi ...

  • Schneider Electric EM4000 - page 39

    930-134-01-A.00 PowerLogic TM Series EM4000 11/2013 Installation Guide ©2013 Schneider Electric All Rights Reserved 31 Regulatory Compliance The PowerLogic EM4000 mete r must be installed by a qualified electrician with knowledge of local installation regulations. Initial installation of the unit, and any subsequent modificatio n to the unit, must ...

  • Schneider Electric EM4000 - page 40

    PowerLogic TM Series EM4000 930-134-01-A.00 Installation Guide 11/2013 32 ©2013 Schneider Electric All Rights Reserved Table 4: Graphical symbols that appea r on equipment Symbol Description Indicate s the supply wire protec tive earth, also known as chassis ground, for the primary gr ound. This symbol indicates a replaceable fuse. ...

  • Schneider Electric EM4000 - page 41

    930-134-01-A.00 PowerLogic TM EM4000 Series 11/2013 Index ©2013 Schneider Electric All Rights Reserved 33 English Index Numerics 347V installation typical three-pha se configuration 10 5A converters and current transformers install 21 5A current transformers install 25 A audience 1 C compliance electrical safety 5 connect Modbus 25 control voltage ...

  • Schneider Electric EM4000 - page 42

    PowerLogic TM EM4000 Series 930-134-01-A.00 Index 11/2013 ©2013 Schneider Electric All Rights Reserved 34 English meter 2 S sense voltage meter 2 sense voltage and control voltage cable in stallation wye and delta service 11 servicing equipment 31 site planning 6 site preparation lighting 7 power 7 start-up sequence 26 U usage environment meter 2 ...

  • Schneider Electric EM4000 - page 43

    ...

  • Schneider Electric EM4000 - page 44

    PowerLogic TM Series EM4000 High-Density Meter Installation Guide Schneider Electric 35 rue Joseph Monier 92500 Rueil-Malmaison, France www.schneider-electric.com 930-134-01-A.00 11 /2013 ©2013 All Rights Reserved PowerLogic is a trademark or regi stered trademar k of Schneider Electric in France, the USA and other countries. Ot her trademarks use ...

Produzent Schneider Electric Kategorie Marine Instruments

Dokumente, die wir vom Produzenten des Geräts Schneider Electric EM4000 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Schneider Electric
- Bedienungsanleitungen EM4000
- Produktkarten Schneider Electric
- Informationsbroschüren
- oder Energieetiketten Schneider Electric EM4000
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Schneider Electric EM4000.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Schneider Electric EM4000, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Schneider Electric EM4000. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Schneider Electric EM4000 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Schneider Electric EM4000, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Schneider Electric EM4000 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Schneider Electric EM4000 verständlich ist.

Eine gänzliche Bedienungsanleitung von Schneider Electric sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Schneider Electric EM4000 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Schneider Electric EM4000 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Schneider Electric EM4000, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Schneider Electric EM4000 - die uns die ersten Schritte während der Nutzung von Schneider Electric EM4000 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Schneider Electric EM4000 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Schneider Electric EM4000 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Schneider Electric EM4000?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Schneider Electric EM4000 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Schneider Electric EM4000 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)