Bedienungsanleitung Security Centres 808

22 Seiten 0.18 mb
Download

Zur Seite of 22

Summary
  • Security Centres 808 - page 1

    496336 Issue 1 1 of 22 808 Installation and User Guide Compatible Equipment 927 8 character LCD keypad new style case 929 8 character LCD keypad 947 Portable printer ( Battery powered ) and power supply unit 949 Wall Mounted Printer Bracket 951 Printer lead 9040 16 Ohm internal sounder 9056 Plug-on Digital Communicator Plug-on RedCare STU (manufact ...

  • Security Centres 808 - page 2

    2 of 22 496336 Issue 1 Introduction The 808 is a programmable Alarm System suitable for domestic or small commercial premises. The system comprises an end station in a shielded case, and up to four separate keypads. The end station provides: • Connections for up to eight Fully Supervised Loop (FSL) or Closed Circuit zones (selectable during progr ...

  • Security Centres 808 - page 3

    496336 Issue 1 3 of 22 T echnical Specification General Operating temperature = -10º - +40ºC. Humidity = 80% RH. Dimensions (end station) = h x w x d 300 x 300 x 80mm. Weight (end station) = Approximately. 5Kg. Power Supply System Power Supply (Ambient Temp. 20 º. C) = 900 mA. With the system quiescent, this supply is used as follows: 808 end st ...

  • Security Centres 808 - page 4

    4 of 22 496336 Issue 1 Zone Wiring The recommended maximum distance for FSL zones using standard alarm cable is 200m - 300m. Software Limits The 808 can support: • One to four Levels. • Four Areas in total. • Eight zones provided by the end station PCB plus one zone pro- vided by each keypad. • Three outputs provided by the end station PCB. ...

  • Security Centres 808 - page 5

    496336 Issue 1 5 of 22 Enabling/Disabling Keys, Display and Sounder 5. Press ‘Enter’. LED 2 lights and the display shows the status of the keypad sounder: 0 for sounder ‘ON’ or 1 for sounder ‘OFF’, for example: 2- 0 6. Change the keypad sounder status as required by entering 0 or 1. (The keypad sounder is normally left at ON = ‘ZERO? ...

  • Security Centres 808 - page 6

    6 of 22 496336 Issue 1 Wiring The 808 main PCB has facilities for connecting: Four keypads. Eight 2-wire FSL detector zones or eight 4-wire closed circuit zones. Siren (Loudspeakers). Three outputs. Figure 2 shows the control unit connector. Zone 8 CCT 8 A/T 8 Zone 7 CCT 7 A/T 7 Tamper return Siren 12V Bell (OP1) OP2 OP3 +ve -ve Outputs 12V Aux 0V ...

  • Security Centres 808 - page 7

    496336 Issue 1 7 of 22 I/P SND SIG SRQ +VE 0V Prog Test 1 2 Vol Display Rear of keypad pcb Tamper N/O Exit Terminate Button or N/C Lock Set Switch End Station Connections 0V SIG +V SRQ Extension Piezo 12VDC E.E. Sounder 25mA Max. + - To other keypad(s) FEZ To detector Figure 3. Wiring the 927 Keypad Important: Please do not connect other devices (f ...

  • Security Centres 808 - page 8

    8 of 22 496336 Issue 1 2k2 EOL 4k7 Zone 1 CCT Alarm contacts Tamper Loop Zone 1 AT Note: When wiring FSL zones, link out the anti-tamper terminals of each zone in use on the main connnector and expander cards. Figure 4. Wiring Diagram for Single Alarm Contacts and Tamper Wiring With the loop in a normal state and the alarm contacts closed (shorting ...

  • Security Centres 808 - page 9

    496336 Issue 1 9 of 22 4. Press 0. The display shows: 0:INST PROG 5. Press Enter. The display prompts you to remove the end station lid: REMOVE LID 6. If the end station Tamper Switch is already open, close and open it again. You have now reached the Installer programming mode. The display shows: 00-PROG SYSTEM Finding Menu Items The 808 programmin ...

  • Security Centres 808 - page 10

    10 of 22 496336 Issue 1 Programming Chart 808 Allocate Areas to Levels Allocate keyzones to Levels Allocate Exit Mode Set Exit Time Set Entry Time Select Alarm Type Assign Entry/Exit tones to keypads Enable/Disable keys 1&3 (PA) and keys 7&9 (Control) Change zone circuit type to FSL CC 21:zone expander options 20: zone expansion 11: edit na ...

  • Security Centres 808 - page 11

    496336 Issue 1 11 of 22 808 Programming Chart Installer Code Audible/Silent/Hidden Tamper, audible, or silent Zone omission 24hr omission Installer reset Anticode reset CSID code RedCare Reset Logging Printer For all types select normally energised or normally de- energised. Continuous siren Bell Run Time, Bell Delay 50: program outputs 51: program ...

  • Security Centres 808 - page 12

    12 of 22 496336 Issue 1 Changing Menu Items After selecting a menu, press Enter to see further options belonging to that menu. The system usually displays an abbreviation for the name of the option, and the values the option currently has. A flashing character marks the part of the display that will change when you next press a key. During programm ...

  • Security Centres 808 - page 13

    496336 Issue 1 13 of 22 The display shows the zone number and current attribute. Note that the zone number is flashing (shown here by an underline). Z0 1-NU To select a zone number: 3. Press the up or down arrow keys (A or B) until you see the zone number you want (in this example zone 3). The display shows: ZO 3-NU 4. Press Enter. The displays sto ...

  • Security Centres 808 - page 14

    14 of 22 496336 Issue 1 12. Continue using the right and left arrow keys (C or D) to select attributes and the up or down arrow keys (A or B) to enable or disable them. Note that if you press the left arrow key (D) too often the display will move back to showing the zone number and type only. Simply press the right arrow key (C) until the display s ...

  • Security Centres 808 - page 15

    496336 Issue 1 15 of 22 Figure 5 shows which letters belong to each number key. Select the letter you want, press the key shown the correct number of times. Use the right arrow key to move the cursor to the next space for a new letter. If you make a mistake, use the left or right arrow keys to move the cursor over the letter you want to change, and ...

  • Security Centres 808 - page 16

    16 of 22 496336 Issue 1 2. Press Menu. If the end station lid is open, the displays shows: REPLACE LID 3. Close the end station lid. If no faults are present the display shows the time: 09:00 If faults exist, the display will show, for example: CANT EXT 01 FLTS REVIEW FAULTS 4. Use the up and down arrow keys to view faults present on the system. Re ...

  • Security Centres 808 - page 17

    496336 Issue 1 17 of 22 Resetting Customer and Installer Codes (First stage reset) If the installer and/or user codes have been lost, or you need to return the end station to the factory default access codes, you can load the default codes as follows: 1. Disconnect mains and battery power to the system. 2. Place a small screwdriver blade between th ...

  • Security Centres 808 - page 18

    18 of 22 496336 Issue 1 8. Press Enter. The display shows: LOADING DEFAULTS Followed by: 00:PROG SYSTEM The end station now has the full set of Scantronic factory defaults and needs reprogramming. NOTES: 1) The Bell output will be energised. If a SAB triggers at this point then check Menu 51. 2) If you remove power during programming, and you have ...

  • Security Centres 808 - page 19

    496336 Issue 1 19 of 22 Menu 50: Program outputs Menu 51: Output Types = Bell = Normally On, Strobe = Normally Off, All other NO Function Menu 52: Internal sounder = Follows Bell Menu 53: Bell Delay = 0, Bell Time = 20 Minutes Menu 60: Program System Options Menu 61: Installer information = Code = 7890 Menu 62: PA response = Audible Menu 63: Line F ...

  • Security Centres 808 - page 20

    20 of 22 496336 Issue 1 you have removed power from the end station while in programming mode with a configuration error.) The end station will not let you leave programming mode until you have cured a configuration error. Note: In a configuration checking error message the display always shows the words "CFG ERR" alternating with one of ...

  • Security Centres 808 - page 21

    496336 Issue 1 21 of 22 The Supervisor can give users 02 to 08 one or more of the following access rights: • Enter a Duress code. • Either Full use (set and unset the Levels they are linked to) or Arm only (set but not unset a Level). • Omit Zones. • Read the system log. • Print from the system log. • Change Zone names. • Reset Levels ...

  • Security Centres 808 - page 22

    22 of 22 496336 Issue 1 To gain access to these menus from a keypad the user must key in: [Access Code] + [Menu key] + [Menu Number] For more information on using the 808 see "808 User Guide". Installer Setting When you leave Programming Mode the system will allow you to enter the Installer access code and use menus 4, 6, 7 and 9. In addi ...

Produzent Security Centres Kategorie Home Security System

Dokumente, die wir vom Produzenten des Geräts Security Centres 808 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Security Centres
- Bedienungsanleitungen 808
- Produktkarten Security Centres
- Informationsbroschüren
- oder Energieetiketten Security Centres 808
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Security Centres 808.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Security Centres 808, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Security Centres 808. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Security Centres 808 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Security Centres 808, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Security Centres 808 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Security Centres 808 verständlich ist.

Eine gänzliche Bedienungsanleitung von Security Centres sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Security Centres 808 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Security Centres 808 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Security Centres 808, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Security Centres 808 - die uns die ersten Schritte während der Nutzung von Security Centres 808 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Security Centres 808 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Security Centres 808 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Security Centres 808?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Security Centres 808 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Security Centres 808 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)