Deutsch dropdown-ico

Bedienungsanleitung Hearth and Home Technologies HUDBAY-INS

37 Seiten 3.34 mb
Download

Zur Seite of 37

Summary
  • Hearth and Home Technologies HUDBAY-INS - page 1

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 1 • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance. - Do not touch any electrical switch. Do not use any phone in your building. - Immediately ...

  • Hearth and Home Technologies HUDBAY-INS - page 2

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 2 APPROVED FOR CANADA AND USA TO: ANSI Z21.88b-2003 / CSA 2.33b-2003 Vented Gas Fireplace Heate r , and applicab le sections o f UL307b Gas Burning Heating Appliances for Manufactured Homes and Recreat iona l V ehicles, CAN/C G A 2.1 7-M9 1 “ Gas Fir ed Appliance s for u se at Hi g ...

  • Hearth and Home Technologies HUDBAY-INS - page 3

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 3 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Glass Speci fi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. BTU Speci fi cations . . . . . . . . . . . . . . . . ...

  • Hearth and Home Technologies HUDBAY-INS - page 4

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 4 Manufactured Home or Mobile Home installation may occur only after the home is site located and must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installa ...

  • Hearth and Home Technologies HUDBAY-INS - page 5

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 5 A. Design and Installation Considerations Quadra-Fire direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. 2 2 Get ting Star ted ...

  • Hearth and Home Technologies HUDBAY-INS - page 6

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 6 Figure 3.1 Model A B C D Hudson Bay Insert Inches 14 1 1 12 7 Millimeters 356 279 305 178 B. Clearances to Combustibles 3 3 F raming and Clearances Note: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONL Y . • Illustrations/diagrams are not drawn to ...

  • Hearth and Home Technologies HUDBAY-INS - page 7

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 7 Fire Risk. Asphyxiation Risk. • T erminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. V ent T ermination Minimum Clearances Figure 4.1 speci fi es minimum vent heights for various pitched roofs. Roof Pitch H (Min.) ...

  • Hearth and Home Technologies HUDBAY-INS - page 8

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 8 TERMINA TION CAP ADAPTER FLEX PIPE TRANSITION ASSEMBL Y SHIPPING BRACKETS A TTACHED TO REAR OF APPLIANCE FOR USE AS LEVELING LEGS A. V enting and Installation Tools and supplies needed: Pliers; Phillips screwdriver; Tape measure; Level; Electrical drill and bits; Square; and High T ...

  • Hearth and Home Technologies HUDBAY-INS - page 9

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 9 INSULA TION V=10 FT . (3 M) MINIMUM 40 FT . (12 M) MAXIMUM TERMINA TION CAP ADAPTOR INLET AIR VENT PIPE EXHAUST AIR VENT PIPE Figure 5.3 Note: Insulation is not included with the venting kit. THIS OPTION SHOWS THE AIR INLET TERMINA TING IN THE CHIMNEY . Fire Hazard. Asphyxiation Ri ...

  • Hearth and Home Technologies HUDBAY-INS - page 10

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 10 Figure 6.2 Kit contents: Replacement ori fi ce; replacement pilot injector; valve regulator; conversion label. T ools required: Ratchet with 7/16 in. (1 1 mm) socket and 2 in. - 4 in. (51-102 mm) extension: power drill (a 90° handle is helpful); #2 Phillips bit; 5/32 in. (4 mm) ...

  • Hearth and Home Technologies HUDBAY-INS - page 11

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 1 1 Figure 6.5 Figure 6.6 Figure 6.7 A B C Figure 6.8 C. V alve Regulator Replacement Remove upper and lower back shield. Loosen the set col- lars on the extension rods with the 3/32 in. Allen wrench. Remove the rods and adapter cap. T urn control knob to the OFF position, ensure tha ...

  • Hearth and Home Technologies HUDBAY-INS - page 12

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 12 Ensure that the rubber gasket (D) is properly positioned and install the new HI/LO pressure regulator assembly to the valve using the new screws (E) supplied with the kit. T ighten screws securely . (Reference torque = 25 in./lb.) Install the enclosed identi fi cation label (F) t ...

  • Hearth and Home Technologies HUDBAY-INS - page 13

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 13 Leak test all gas line joints and the gas control valve prior to and after starting the appliance. Before making the gas connection, ensure that the appliance you are installing is designed for the type of gas being supplied. This information can be found on the ratings label unde ...

  • Hearth and Home Technologies HUDBAY-INS - page 14

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 14 C. Standing Pilot Ignition System Wiring This appliance DOES NOT require 1 10 V AC supply for operation. A wiring diagram is shown in Figure 7.2 on the next page. This appliance is equipped with a millivolt control valve. Do not connect this appliance to a thermostat serving any o ...

  • Hearth and Home Technologies HUDBAY-INS - page 15

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 15 Figure 7.2 ROCKER SWITCH / W ALL THERMOST A T / REMOTE V ARIABLE REGULA TOR PILOT ADJUSTMENT CAP MANIFOLD PRESSURE INLET PRESSURE PUSH BUTTON IGNIT OR THERMOPILE IGNITOR PILOT THERMOCOUPLE CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can ca ...

  • Hearth and Home Technologies HUDBAY-INS - page 16

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 16 C. Door Crown Installation Open lower access panel. Pull out and unhook the two spring latches on the bottom of the appliance that secure the door. Rotate the door forward approximately 1-1/2 in. (38 mm). Holding the ashlip, lift the door up off of the stationary latches and away ...

  • Hearth and Home Technologies HUDBAY-INS - page 17

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 17 D. Grille Installation Remove the door of appliance. Remove the four screws (two at each end) holding grille in place. Lift up to remove. Figure 8.5 Determine your desired placement of the rocker switch. 1 If you wish to place it on the control panel in the "Main Burner" ...

  • Hearth and Home Technologies HUDBAY-INS - page 18

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 18 F . Brick Installation The pilot shield has to be removed to install or remove the brick refractory . Removal of the bracket requires remov- ing two screws. Figure 8.10 Figure 8.1 1 Figure 8.12 Figure 8.13 Figure 8.14 Figure 8.9 PILOT BRACKET PILOT SHIELD T o install the baf fl e ...

  • Hearth and Home Technologies HUDBAY-INS - page 19

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 19 G. Positioning the Logs While still breakable, the logs do not become fragile until after the appliance is burned and they have cured. After curing, any handling must be done with care as breakage can easily occur . Figure 8.16 Figure 8.19 Figure 8.17 Figure 8.20 Figure 8.18 Figur ...

  • Hearth and Home Technologies HUDBAY-INS - page 20

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 20 H. Mineral W ool I. Blower Installation Included in kit: Blower . T ools required: Powered Phillips head screwdriver . Figure 8.23 Figure 8.24 Figure 8.25 Figure 8.21 I nstall the left twig (#6) over the locator pins in the right rear log and the left front log. Explosion Risk. ? ...

  • Hearth and Home Technologies HUDBAY-INS - page 21

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 21 Figure 8.26 Figure 8.27 Installation is the reverse of removal. Figure 8.28 Blower Wiring Diagram F = 1/4 in. (6 mm) female spade M = 1/4 in. (6 mm) male spade Disconnect wires from the blower. Remove grommet retainer from old blower and install on new blower. BLOWER M M F F BLK B ...

  • Hearth and Home Technologies HUDBAY-INS - page 22

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 22 Figure 8.29 J. Air Shutter Adjustment The air shutter is used to fine-tune the flame as necessary. The air shutter is shipped in the fully open position. Allow the unit to operate 15-20 minutes before making any adjustments to the air shutter. This will give the flame time to reac ...

  • Hearth and Home Technologies HUDBAY-INS - page 23

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 23 A. Before Lighting Appliance Read this entire manual prior to using the appliance. Failure to follow the instructions may result in property damage, bodily injury, or even death. 9 9 Operat ing Instruc tions Before operating this appliance have a quali fi ed tech- nician: • Rem ...

  • Hearth and Home Technologies HUDBAY-INS - page 24

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 24 B. Lighting Appliance 1. Set the thermostat to lowest setting. 2. T urn off all electric power to the appliance if service is to be performed. 3. Push in gas control knob slightly and turn clockwise to "OFF" position. FOR YOUR SAFETY READ BEFORE LIGHTING FOR YOUR SAFETY ...

  • Hearth and Home Technologies HUDBAY-INS - page 25

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 25 Initial Break-in Procedure When you light the appliance, you may notice that it pro- duces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 ...

  • Hearth and Home Technologies HUDBAY-INS - page 26

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 26 A. Standing Pilot Ignition System 1 0 10 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service person in the ...

  • Hearth and Home Technologies HUDBAY-INS - page 27

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 27 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater ...

  • Hearth and Home Technologies HUDBAY-INS - page 28

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 28 A. Glass Replacement Glass can be replaced either as three separate pieces, or as an assembly with the door. See Service Parts List. T o Replace Separate Glass Pieces • Turn of f gas to the appliance. • Remove the door and set on a protective surface. • Remove the door crown ...

  • Hearth and Home Technologies HUDBAY-INS - page 29

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 29 Inspect Maintenance T asks Doors 1. Inspect for scratches, dents or other damage and repair as necessary . 2. V erify no obstructions to air fl ow . 3. V erify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Assembly and Glass 1. Inspect gaske ...

  • Hearth and Home Technologies HUDBAY-INS - page 30

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 30 MINIMUM FIREBOX OPENING Height: Width: Depth: Front Rear Front Rear T op Bottom Inches 20-1/4 14-1/2 26-1/2 20 13 13 Millimeters 514 368 673 508 330 330 ROCKER SWITCH AND WIRING IS ACCESSIBLE HERE WHEN SHIPPED ELECTRICAL CONNECTION AND GAS CONNECTION EXTEND FROM HERE RIGHT SIDE OF ...

  • Hearth and Home Technologies HUDBAY-INS - page 31

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 31 B. V ent Components List V enting System Components Description HHT Component # LINK-DV4-30B Includes one piece 3 in. x 30 ft. Flex; one piece 3 in. x 4 ft. Flex; Cap/Adapter Linear to Coaxial with Flashing. Dura-V ent GS Catalog # 923GK Colineal Flex Connector 991 High Wind V ert ...

  • Hearth and Home Technologies HUDBAY-INS - page 32

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 32 R Service Parts Diagram Hudson Bay Insert HUDBA Y -INS Beginning Manufacturing Date: April 2003 Ending Manufacturing Date: ______ Service Parts Part number list on following page. Log Set Assembly 1 11 10 9 7 6 8 12 13 2 3 4 5 ...

  • Hearth and Home Technologies HUDBAY-INS - page 33

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 33 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked In Depot ITEM DESCRIPTION SERIAL # P ART NUM ...

  • Hearth and Home Technologies HUDBAY-INS - page 34

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 34 R V alve Assembly Diagram Hudson Bay Insert HUDBA Y -INS Beginning Manufacturing Date: April 2003 Ending Manufacturing Date: ______ Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number a ...

  • Hearth and Home Technologies HUDBAY-INS - page 35

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 35 D. Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and instal ...

  • Hearth and Home Technologies HUDBAY-INS - page 36

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 36 D. Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust ...

  • Hearth and Home Technologies HUDBAY-INS - page 37

    Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 37 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .quadra fi re.com E. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer , p ...

Produzent Hearth and Home Technologies Kategorie Indoor Fireplace

Dokumente, die wir vom Produzenten des Geräts Hearth and Home Technologies HUDBAY-INS erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Hearth and Home Technologies
- Bedienungsanleitungen HUDBAY-INS
- Produktkarten Hearth and Home Technologies
- Informationsbroschüren
- oder Energieetiketten Hearth and Home Technologies HUDBAY-INS
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Hearth and Home Technologies HUDBAY-INS.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Hearth and Home Technologies HUDBAY-INS, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Hearth and Home Technologies HUDBAY-INS. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Hearth and Home Technologies HUDBAY-INS ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Hearth and Home Technologies HUDBAY-INS, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Hearth and Home Technologies HUDBAY-INS hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Hearth and Home Technologies HUDBAY-INS verständlich ist.

Eine gänzliche Bedienungsanleitung von Hearth and Home Technologies sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Hearth and Home Technologies HUDBAY-INS bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Hearth and Home Technologies HUDBAY-INS befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Hearth and Home Technologies HUDBAY-INS, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Hearth and Home Technologies HUDBAY-INS - die uns die ersten Schritte während der Nutzung von Hearth and Home Technologies HUDBAY-INS erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Hearth and Home Technologies HUDBAY-INS hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Hearth and Home Technologies HUDBAY-INS im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Hearth and Home Technologies HUDBAY-INS?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Hearth and Home Technologies HUDBAY-INS nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Hearth and Home Technologies HUDBAY-INS hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)