Bedienungsanleitung Honeywell Y343B1002

11 Seiten 1.07 mb
Download

Zur Seite of 11

Summary
  • Honeywell Y343B1002 - page 1

    Honevwell THE Y343B IGNITION PACKAGE PROVIDES DIRECT SPARK IGNITION (DSI) FOR GAS HEATING SYSTEMS. THE PACKAGE IN- CLUDES THE S87D ELECTRONIC MODULE, Q354A FLAME SENSOR, Q347A SPARK IG- NITER-SENSOR AND 392286-l IGNITION CABLE. DEPENDABLE BURNER IGNITION 0 Spark generated by electronic module and internal step-up transformer. SOLID STATE DESIGN 17 ...

  • Honeywell Y343B1002 - page 2

    SPECIFICATIONS 4 The Y34381002 Direct Soark Gas Burner lanition Package includes the S87D ilectronic Module, 6347A Spark Igniter-Sensor, Q354A Flame Sensor and 392286-l Ignition Cable Assembly. Other controls needed to complete the heating sys- tem include a 24 V, DSI gas valve; 24 V thermostat; 24 V transformer and high temperature limit controlle ...

  • Honeywell Y343B1002 - page 3

    AMBIENT TEMPERATURE RATING: Minus 40 F to plus 175 F [minus 40 C to plus 79 C]. WIRING CONNECTIONS: l/4 in. [6.4 mm] male quick-connect terminals, for all except ALARM ter- minal. ALARM terminal, l/4 in. [6.4 mm] female quick-connect. l/4 in. [6.4 mm] diameter stud base for ignition cable. REPLACEMENT PARTS: 3 A fuse. Q347A SPARK IGNITER-SENSOR The ...

  • Honeywell Y343B1002 - page 4

    TABLE l-GAS CONTROLS. MODEL NO. V845A VR8450A V845C VR8450C VR8540A VR8590A VR8600A TYPE OF PRESSURE REGULATOR Standard Standard Step-open Step-open Two-stage Negative Negative CAPACITY RANGE OF STANDARD MODEL cfh mJ/hr 110to335 3.1 to 9.5 110to290 3.1 to 7.8 11oto335 3.1 to 9.5 110to290 3.1 to 7.8 110to290 3.1 to 7.8 37 to 400 1.oto 11.3 37 to 400 ...

  • Honeywell Y343B1002 - page 5

    Position the Q347 so that only the tips of the elec- trodes are immersed in the burner flame. The burner must ignite smoothly - usually this will be ac- complished with tip of electrodes (spark gap) spaced approximately l/4 in. [6.4 mm] from the surface of the burner. Gas must flow into one of the three open sides of the spark gap (where outer elec ...

  • Honeywell Y343B1002 - page 6

    Q354A FLAME SENSOR 1. Mate quick-connect terminals (l/4 in. [6.4 mmf)’ are provided on both the Q354 and S87D. Connect the SENSOR terminal on the 587 to the terminal on the Q354 as shown in Fig. 4. Use thermoplastic insulated wire with a minimum rating of 105 C [221 F] for the flame sensor leadwire; asbestos insulation is not acceptable. AUXILIAR ...

  • Honeywell Y343B1002 - page 7

    FIG. B-WIRING HOOKUP FOR Y343B PACKAGE IN A TYPICAL TWO-STAGE DSI HEATING SYSTEM. ,, “,, ~ ,,, I ,,,, ,. ,.., :. II ,, , .xI,. j ,,,. ., _ ,-, CI ,x .,,, ., . .x _^.,” ~.. ,, ,IX ^ _, FIG. 7-S67D SIMPLIFIED SCHEMATIC DIAGRAM. 7 66-00?4 ...

  • Honeywell Y343B1002 - page 8

    STARTUP AND CHECKOUT The following start-up and checkout procedures are basic to the S87. If possible, refer to the specific instructions provided by the appliance manufacturer since the application and controls used may differ. NOTE: If one of the system components fails, the S87 will either not operate or it will go into safety lockout (depending ...

  • Honeywell Y343B1002 - page 9

    FIG. a--NORMAL SYSTEM SEQUENCE OF OPERATION. SERVICE l Only persons trained and experienced in DSI systems should service this equipment. If a condition exists that causes the S87D electronic module to go into safety lockout, meter readings must be taken quickly after restart - within trial-for-ignition period. Always de-energize the system for at ...

  • Honeywell Y343B1002 - page 10

    GROUNDING CONNECTIONS A common ground is required for the burner, spark igniter-sensor mounting bracket and the GND terminal of the 587. If ground is poor or erratic, safety shutdown may occur occasionally even though operation is nor- mal at time of checkout. Therefore, if nuisance shut- downs have been reported, be sure to check ground connection ...

  • Honeywell Y343B1002 - page 11

    t TROUBLESHOOTING . Start the system by setting the thermostat (tem- down to the next box. If the condition is not true or not perature controller) to call for heat. Observe the system okay (answer is no), go to the box at right. Continue response and establish the type of malfunction or checking and answering conditions in each box until a deviati ...

Produzent Honeywell Kategorie Burner

Dokumente, die wir vom Produzenten des Geräts Honeywell Y343B1002 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Honeywell
- Bedienungsanleitungen Y343B1002
- Produktkarten Honeywell
- Informationsbroschüren
- oder Energieetiketten Honeywell Y343B1002
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Honeywell Y343B1002.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Honeywell Y343B1002, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Honeywell Y343B1002. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Honeywell Y343B1002 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Honeywell Y343B1002, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Honeywell Y343B1002 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Honeywell Y343B1002 verständlich ist.

Eine gänzliche Bedienungsanleitung von Honeywell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Honeywell Y343B1002 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Honeywell Y343B1002 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Honeywell Y343B1002, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Honeywell Y343B1002 - die uns die ersten Schritte während der Nutzung von Honeywell Y343B1002 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Honeywell Y343B1002 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Honeywell Y343B1002 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Honeywell Y343B1002?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Honeywell Y343B1002 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Honeywell Y343B1002 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)