Bedienungsanleitung Honeywell MS7580

48 Seiten Betrifft nicht
Download

Zur Seite of 48

Summary
  • Honeywell MS7580 - page 1

    MetroSelect ® Area Imaging Supplemental Configuration Guide ...

  • Honeywell MS7580 - page 2

    Disclaimer Honeywell International In c. (“HII”) reserves the ri ght to make changes in specifications and other inform ation cont ained in this docu ment without prior notice, and the reader should in all c ases consult HII to determine whether an y such changes have been made. The inform ation in this publication does not represent a commitme ...

  • Honeywell MS7580 - page 3

    iii T able of Contents Imager Operation Presentation and Trigger Mod es In-St and......................................................................................................... 1 Out-of-S tand .................................................................................................. 2 Out-of-Stand / In-S tand Mode Ma tch.......... ...

  • Honeywell MS7580 - page 4

    iv PDF Opti ons ................................................................................................... 32 RS232 Software Hand shakin g ................................................................................... 33 Multifunctional USB /IBM Interf ace .................................................................. 33 Interface ...

  • Honeywell MS7580 - page 5

    1 Imager Operation Presentation a nd Trigger † Mode s There are four configurable m odes for scanning: the presentation mode, the multi-try trigger mode, the continu ous trigger mode, and the single-trig ger mode. These modes can be config ured se parately for in-stand and out-of-stand imager operation ‡ . In-Stand ‡ * Presentation Mode In-St ...

  • Honeywell MS7580 - page 6

    2 Out-of-Stand ‡  Presentation Mode Out-of-Stand * Multi-Try Trigger Mode Out-of-Stand ³ 418304 ³ 418324 Continuous Trigger Mode Out-of-Stand Single Trigger Mode Out-of-Stand ³ 418354 ³ 418344 In-Stand/Out-of-Stand Mode Match Set In-Stand Mode to Match Out-of-Stand Mode ³ 4202154 * Factory default configuration for t he MS1690, MS1890, an ...

  • Honeywell MS7580 - page 7

    3 * Presentation Mode Immediately After Button † Release  ³ 823800 The imager immediatel y reverts to presentation mode when the button is released.  Presentation Mode 1 second After Button Release  ³ 823820 The imager reverts to presentation mode 1 second after the button is released.  Presentation Mode 5 seconds After Button Relea ...

  • Honeywell MS7580 - page 8

    4 * Enable Trigger Press Timeout In Presentation Mode  Disable Trigger Press Timeout In Presentation Mode  ³ 124403 ³ 124413 * Factory default configuration.  This feature is only supported in the Focus ® product series (i.e., IS1650, MS1890, MS1633, and the MS1690). ...

  • Honeywell MS7580 - page 9

    5 Pass-Through Settings  * Enable Pass-Through Scanning In Presentation Mode  Disable Pass-Through Settings In Presentation Mode  ³ 127015 ³ 127005 Enable 300 milliseconds Pass-Through Timeout  ³ 8439300 Enable 100 milliseconds Pass-Through Timeout  ³ 8439100 * Factory default configuration for t he MS7580. † The term tri ...

  • Honeywell MS7580 - page 10

    6 Omnidirectional and/or Li near Imager Modes The area imager can be configure d to oper ate as an omnidirectional ima ger, or a linear imager, or a combination of both. T rigger † and presentation op erations can be configured separ ately for omnidi recti onal and linear sca n modes. • When a unit is configured to operat e as an o mnidirection ...

  • Honeywell MS7580 - page 11

    7 Enable 1D Linear Only in Trigger Operations Disable 1D Linear Only in Trigger Operations ³ 120212 ³ 120202 Enable Linear Only in Presentation Operations Disable Linear Only in Presentation Operations ³ 120211 ³ 120201 Enable 1D Linear Only in Presentation Operations Disable 1D Linear Only in Presentation Operations ³ 120210 ³ 120200 ...

  • Honeywell MS7580 - page 12

    8 Aiming and Illumination Trigger and presentati on operations can be configured s eparately to use the imager’s linear illumin ation as an aiming instrument. * Enable Aiming in Trigger Operations Disable Aiming in Trigger Operations ³ 124000 ³ 124010 * Enable Aiming in Presentation Operations Disable Aiming in Presentation Operations ³ 124011 ...

  • Honeywell MS7580 - page 13

    9 * Enable Auto Gain Disable Auto Gain ³ 125101 ³ 125111 * Enable Illumination Group 1 Disable Illumination Group 1 ³ 124002 ³ 124012 * Enable Illumination Group 2  Disable Illumination Group 2  ³ 124003 ³ 124013 * Factory default c onfiguration.  This feature is only supported in the Focus product series (i.e., IS1650, MS1890, MS163 ...

  • Honeywell MS7580 - page 14

    10 Data Output * Enable Data Output Disable Data Output ³ 121205 ³ 121215 * Factory default configuration. ...

  • Honeywell MS7580 - page 15

    11 Character Suppression Enable the Suppression of 1 Character * Disable the Suppression of 1 Character ³ 115111 ³ 115101 To suppress 1 ch aracter: 1. Scan the Enter/Exit Configura tion Mode bar code, on page 39. 2. Scan the Enable the Suppression of 1 Ch aracter bar code. 3. Scan the Character 1 bar code ( below left ). 4. Scan the three code by ...

  • Honeywell MS7580 - page 16

    12 Code Bytes 0 – 9 Notes: F or additional information on Code B ytes, refer to the Code Bytes Usage section of the MetroSelect C onfiguration Guid e (PN 00-02544). ³0 Code Byte 0 ³1 Code Byte 1 ³2 Code Byte 2 ³3 Code Byte 3 ³4 Code Byte 4 ³5 Code Byte 5 ³6 Code Byte 6 ³7 Code Byte 7 ³8 Code Byte 8 ³9 Code Byte 9 ...

  • Honeywell MS7580 - page 17

    13 Same Symbol Timeouts Retain Same Symbol Timeout on Trigger * Reset Same Symbol Timeout on Trigger ³ 120013 The same-symbol timeout is not restarted when the trigger is pulled. ³ 120003 The same-symbol timeout is restarted when the trigger is pulled. LED Options * Normal Blue LED Intensity  Low Blue LED Intensity  ³ 143100 ³ 143110 * No ...

  • Honeywell MS7580 - page 18

    14 ...

  • Honeywell MS7580 - page 19

    15 Imager Operation – MS1633 Power Save Modes †† Enable Trigger Power-Save * Disable Trigger Power-Save ³ 125315 When enabled, the MS1633 will enter sleep mode after the trigger is held for 10 seconds. ³ 125305 Enable IR Power-Save Disable IR Power-Save ³ 125314 When enabled, the MS1633 will enter sleep mode after the IR has been activated ...

  • Honeywell MS7580 - page 20

    16 RangeGate ® Mode †† Enable RangeGate Disable RangeGate ³ 123707 When enabled, the MS1633 will store scanned bar codes into non-volatile memory if the wireless connection has been interrupted. ³ 123717 Note: RangeGate and Inventor y Mode are mutually exclusive. If both are enabled, Inventory Mode takes priorit y. RangeGate Delay = 1 sec. R ...

  • Honeywell MS7580 - page 21

    17 Firmware Version and Addr ess †† Transmit the Firmware Version of the Imager with Bluetooth ® Wireless Technology ³ 998044 Transmit the Address of the Imager with Bluetooth Wireless Technol ogy ³ 998045 †† These features are no t for use with the MS1690, MS1890 or the IS1650. ...

  • Honeywell MS7580 - page 22

    18 Inventory M ode †† In Inventory mode, there is a quantity fi eld associated with each bar code. When an item’s bar code is sc anned, the MS1633 automatically stor es the bar code data in its non-volatile memor y with a quantity field set to 1. T he quantity field can then be modified using the qu antity bar codes on page 20. The bar code d ...

  • Honeywell MS7580 - page 23

    19 The quantity bar codes on pa ge 20 enable the user to enter a quantit y for the last item scanned. The item’s bar c ode data will be stored and transmitted as many times as the quantity indicates. If the Transmit Quantit y Field feature (on page 18) has been en abled then the bar code dat a will be stored and transmitted once with a numerical ...

  • Honeywell MS7580 - page 24

    20 Quantity Codes †† Quantity 0 Quantity 5 ³Q 0 ³Q 5 Quantity 1 Quantity 6 ³Q 1 ³Q 6 Quantity 2 Quantity 7 ³Q 2 ³Q 7 Quantity 3 Quantity 8 ³Q 3 ³Q 8 Quantity 4 Quantity 9 ³Q 4 ³Q 9 †† This feature is not for use with the MS1690, MS1890, or the IS 1650. ...

  • Honeywell MS7580 - page 25

    21 Transmit Entry Counter †† * Do Not Transmit Entry Counter ³ 123914 Optional field transmitted with the bar code data that is a count of the number of transmissions used to transmit the entire buffer. ³ 123904 Transmit Number of Records †† ³ 998051 Will transmit the number of records and the number of bar codes currently stored as a 5- ...

  • Honeywell MS7580 - page 26

    22 Enable Inventory Beep †† * Disable Inventory Beep ³ 123912 When enabled MS163 3 will beep after transmitting each inventory record. ³ 123902 Delete Last Record †† ³ 998063 When scanned, this bar code will delete the last bar code stored. Clear Inventory Records †† ³ 998049 When scanned, this bar code will clear all stored bar cod ...

  • Honeywell MS7580 - page 27

    23 Code T ypes and Decode Rules Data Matrix Enable Normal Color Data Matrix Decoding Enable Inverse Color Data Matrix Decoding ³ 200522 ³ 200512 Enable Normal and Inverse Color Data Matrix Decodin g * Disable Data Matrix Decoder ³ 200532 ³ 200502 Enable Rectangular Data Matrix Symbol Decoding * Disable Rectangular Data Matrix Symbol Decoding ³ ...

  • Honeywell MS7580 - page 28

    24 Enable Low-Contrast Data Matrix Decoding † * Disable Low-Contrast Data Matrix Decoding ³ 125417 Improves decoding † of low-contrast Data Matrix symbols. ³ 125407 Enable Data Matrix Non-Square Modules † * Disable Data Matrix Non-Square Modules ³ 125416 Improves decoding † of Data Matrix symbols when indi vidual module s in the symbol a ...

  • Honeywell MS7580 - page 29

    25 * Enable Data Matrix, Normal Size ³ 325402 The following bar codes improve deco ding of Data Matrix symbols when the length of a symbol size is small. To disable either of these options scan the Enable Data Matrix Normal Size bar code above. Enable Data Matrix, Small Size † Enable Data Matrix Very Small Size † ³ 325412 ³ 325422 * Factory ...

  • Honeywell MS7580 - page 30

    26 QR Code Enable Normal Video QR Code Enable Inverse Video QR Code ³ 200612 ³ 200622 Enable Normal and Inverse QR Code * Disable QR Code ³ 200632 ³ 200602 MaxiCode Enable MaxiCode * Disable MaxiCode ³ 100614 ³ 100604 * Factory default configuration. ...

  • Honeywell MS7580 - page 31

    27 Aztec Enable Normal Video Aztec Decoding * Disable Normal Video Aztec Decoding ³ 100610 ³ 100600 Enable Inverse Video Aztec Decoding * Disable Inverse Video Aztec Decoding ³ 100611 ³ 100601 * Factory default configuration ...

  • Honeywell MS7580 - page 32

    28 Enable Aztec Structure Append Decoding * Disable Aztec Structure Append Decoding ³ 124416 ³ 124406 When this feature is enabled, Aztec bar codes with a structured append header will be stored in the imager’s memory buffer. The imager will transmit the concatenated message once every compon ent of the structured append bar code has been read. ...

  • Honeywell MS7580 - page 33

    29 Postal Enable Australia Post * Disable Australia Post ³ 126217 ³ 126207 Enable Japan Post * Disable Japan Post ³ 126216 ³ 126206 Enable KIX Code * Disable KIX Code ³ 126215 ³ 126205 * Factory default configuration. ...

  • Honeywell MS7580 - page 34

    30 Enable PLANET Code * Disable PLANET Code ³ 126214 ³ 126204 Enable POSTNET Code * Disable POSTNET Post ³ 126213 ³ 126203 Enable B & B’ Fielded POSTNET * Disable B & B’ Fielded POSTNET ³ 126212 ³ 126202 * Factory default configuration ...

  • Honeywell MS7580 - page 35

    31 Enable UPU Decoding * Disable UPU Decoding ³ 126211 ³ 126201 Enable Royal Mail 4 Code * Disable Royal Mail 4 Code ³ 126210 ³ 126200 Enable Zero-FCC Australia Post * Disable Zero-FCC Australia Post ³ 126412 ³ 126402 * Factory default configuration. ...

  • Honeywell MS7580 - page 36

    32 Codablock Options Enable Codablock A * Disable Codablock A ³ 126410 ³ 126400 Enable Codablock F * Disable Codablock F ³ 126411 ³ 126401 PDF Options Enable Transmit as ³ 115113 * Enable Transmit as ³ 115103 * Factory default configuration. ...

  • Honeywell MS7580 - page 37

    33 RS232 Software Handshaking Enable ]V Handshaking Disable ]V Handshaking ³ 125210 An “]V” response from the host indicates reception of imager data. ³ 125200 Multifunctional USB/IBM ® Interface † Dual Interface Defaults † ³ 999923 † This feature is not for use with the MS1633. ...

  • Honeywell MS7580 - page 38

    34 ...

  • Honeywell MS7580 - page 39

    35 Interfaces Additional Interfaces † Enable Beeper ON/OFF Commands * Disable Beeper ON/OFF Commands ³ 125211 Enables beeper on/off commands with internal USB and IBM interfaces. ³ 125201 3 rd Generation IBM 46xx Defaults ³ 999952 First, scan the 3 rd Generation IBM 46xx Default bar code. Then, scan the IBM Reserved Code #2. IBM Reserved Code ...

  • Honeywell MS7580 - page 40

    36 IBM 46xx-SIOC RS485 Interface Send 30H for Last Block Label Identifier 4680 * Send 00 for Last Block Label Identifier 4680 ³ 117215 Note: Feature is for PDF codes only. ³ 117205 Note: Feature is for PDF codes only. IBM-OEM USB Interface Send 30H for Last Block Label Identifier USB * Send 00 for Last Block Label Identifier USB ³ 116300 Note: F ...

  • Honeywell MS7580 - page 41

    37 MS7580 Genesis Specific Load RS232 Configuration Settings  Load USB Configuration Settings  ³ 998071 ³ 998072 Load Keyboard Wedge Configuration Settings  Load RS485 Configuration Settings  ³ 998073 ³ 998074 Recall Configuration for Currently Connected Interface  ³ 998080  This feature is only supported in the MS7580 Genesi ...

  • Honeywell MS7580 - page 42

    38 Apply Settings to All Interfaces  Apply Settings to the Current Interface  ³ 998075 ³ 998081 Apply Settings to RS232 Interface  Apply Settings to USB Interface  ³ 998076 ³ 998077 Apply Settings to Keyboard Wedge  Apply Settings to RS485 Interface  ³ 998078 ³ 998079  This feature is only supported in the MS7580 Genesis. ...

  • Honeywell MS7580 - page 43

    39 Enter/Exit Configuration Mode Enter Exit Configuration Mode ³ 999999 ...

  • Honeywell MS7580 - page 44

    40 ...

  • Honeywell MS7580 - page 45

    41 Cont act Information The Americas (TA) Omniplanar, Inc. Spain USA Tel: 856.374.5550 Tel: +34 913 272 400 Tel: 800.436.3876 Fax: 856.374.5576 Fax: +34 913 273 829 (Customer Service) Email: Email: 866.460.8033 info@omniplanar.com info@es.metrologic.com (Customer Support) 888.633.3762 NOVODisplay United Kingdom (Technical Support) Tel: 856.537.6139 ...

  • Honeywell MS7580 - page 46

    42 Chengdu Sales Office Japan Singapore Tel: 0 2 8 - 6 6 1 3 5 0 6 6 / 8 6 7 8 6 3 4 8 Tel: 81-3-3839-8511 Tel: (65) 6842-7155 Fax: 028-86787061 Fax: 81-3-3839-8 519 Fax: (65) 6842-7166 Email: Email: Email: info@cn.metrologic.com info@jp.metrologic.com info@sg.metrologic.com Hong Kong Korea Thailand Tel: 852-2331-9133 Korea Sales Office Tel: +662-6 ...

  • Honeywell MS7580 - page 47

    ...

  • Honeywell MS7580 - page 48

    Honeywell Scanning & Mob ility 90 Coles Road Blackwood, NJ 08012-4683 00-05252 Rev B June 2009 ...

Produzent Honeywell Kategorie Barcode readers

Dokumente, die wir vom Produzenten des Geräts Honeywell MS7580 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Honeywell
- Bedienungsanleitungen MS7580
- Produktkarten Honeywell
- Informationsbroschüren
- oder Energieetiketten Honeywell MS7580
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Honeywell MS7580.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Honeywell MS7580, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Honeywell MS7580. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Honeywell MS7580 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Honeywell MS7580, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Honeywell MS7580 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Honeywell MS7580 verständlich ist.

Eine gänzliche Bedienungsanleitung von Honeywell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Honeywell MS7580 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Honeywell MS7580 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Honeywell MS7580, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Honeywell MS7580 - die uns die ersten Schritte während der Nutzung von Honeywell MS7580 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Honeywell MS7580 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Honeywell MS7580 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Honeywell MS7580?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Honeywell MS7580 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Honeywell MS7580 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)