Bedienungsanleitung Image IMBE41990

18 Seiten 0.6 mb
Download

Zur Seite of 18

Summary
  • Image IMBE41990 - page 1

    QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing parts, we will guar- antee you complete satisfaction through direct assistance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUSTOMER HOT LINE. The trained tec ...

  • Image IMBE41990 - page 2

    2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Part Identification Chart . . ...

  • Image IMBE41990 - page 3

    3 1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are ade- quately informed of all precautions. 3. The weight bench is intended for home use only . Do not use the weight bench in a com- ...

  • Image IMBE41990 - page 4

    4 Weight Storage T ube Seat Upright Weight Guide Weight Glider Barbell Safety Spotter Right Side Left Side Note: The terms Òright sideÓ and Òleft sideÓ are determined relative to a person sitting on the bench. They do not refer to right and left on the drawings in this manual. Adjustment Bracket Backrest Thank you for selecting the versatile IM ...

  • Image IMBE41990 - page 5

    5 Part Identification ChartÑModel No. IMBE41990 R1299A M10 Nylon Locknut (1 1)Ñ 24 M8 Nylon Locknut (54)Ñ13 M6 W asher (30)Ñ5 M8 x 60mm Bolt (39)Ñ2 M6 x 38mm Bolt (60)Ñ1 M6 x 55mm Bolt (4)Ñ4 M8 x 30mm Bolt (38)Ñ2 M8 x 25mm Bolt (53)Ñ2 M8 x 70mm Bolt (41)Ñ4 M10 x 180mm Bolt (22)Ñ2 M10 W asher (6)Ñ14 M10 x 70mm Bolt (46)Ñ8 M10 x 65mm Bol ...

  • Image IMBE41990 - page 6

    6 1. Before beginning, make sure that you understand the information in the box above. Note: Some parts described in the assembly steps may be pre-assembled. Press a 50mm Square Outer Cap (17) onto each end of a Base (7). T urn the Base so the large hole is in the position shown. Insert two M8 x 65mm Carriage Bolts (59) and two M10 x 65mm Carriage ...

  • Image IMBE41990 - page 7

    4. Slide the remaining Brace (2) onto the bracket on the other Upright (1). Attach the Brace to the Upright with two M10 x 65mm Bolts (42), four M10 W ashers (6), and two M10 Nylon Locknuts (1 1). Do not tighten the Nylon Locknuts yet. Slide the Upright (1) and the Brace (2) onto the M10 x 65mm Carriage Bolts (40) and the M8 x 65mm Carriage Bolts ( ...

  • Image IMBE41990 - page 8

    8 5. Press a 25mm Round Inner Cap (51) into the end of a Weight Storage Tube (21). While a second person holds a Crossbar (8) in the position shown, insert two M10 x 70mm Bolts (46) through the bracket on the Weight Storage T ube (21), the left Brace (2), and the bracket on the Crossbar (8). Thread an M10 Nylon Locknut (1 1) onto each Bolt. Do not ...

  • Image IMBE41990 - page 9

    9 8. Press a 25mm Bushing (48) into each end of the Locking Bar (34). Insert the Barbell (35) through the Locking Bar (34) until the Barbell is centered in the Locking Bar . 35 48 34 48 8 9. Identify the Left Weight Glider (32) by looking at the position of the round tube. Press a 38mm Bushing (29) into each end of the round tube on the Left Weight ...

  • Image IMBE41990 - page 10

    10 12. Place the Right Safety Spotter (23) on the right Base (7) and center it over the indicated hole. Note: The handle must point toward the center of the bench. Have a second person hold the Locking Bar (34) so that the Right Weight Glider (31) rests on top of the Right Safety Spotter (23). Insert a Weight Guide (18) into the Right Weight Glider ...

  • Image IMBE41990 - page 11

    15. Press a 50mm Square Outer Cap (17) onto each end of the Small Stabilizer (25). Attach the Small Stabilizer (25) to the Bench Frame (5) with two M10 x 65mm Carriage Bolts (40) and two M10 Nylon Locknuts (1 1). Note: There is an inden- tation around the holes on one side of the Small Stabilizer . This side must be facing the floor . 15 40 11 5 17 ...

  • Image IMBE41990 - page 12

    12 19. Lubricate an M10 x 180mm Bolt (22). Attach the Backrest T ubes (27) to the indicated tube on the Bench Frame (5) with the Bolt, two M10 W ashers (6), and an M10 Nylon Locknut (1 1). Note: Do not over- tighten the Nylon Locknut; the Backrest T ubes must pivot easily . 20. Attach the Backrest (15) to the Backrest T ubes (27) with four M6 x 55m ...

  • Image IMBE41990 - page 13

    13 23. T urn the Seat (14) as shown. Attach the wide end of the Seat to the bracket on the Seat Support T ube (37) with two M6 x 16mm Screws (3). T ilt the Seat Support T ube (37) upwards and attach the narrow end of the Seat (14) to the Seat Support T ube with an M6 x 38mm Bolt (60) and an M6 W asher (30). 23 60 30 3 37 14 24. Make sure that all p ...

  • Image IMBE41990 - page 14

    14 This section explains how the weight bench is adjusted. See the included exercise guide for important informa- tion about how to perform a variety of exercises and how to get the greatest benefit from your exercise program. Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately . The weight bench can ...

  • Image IMBE41990 - page 15

    15 ADJUSTING THE BACKREST T o raise the Backrest (15), grip the end of the Backrest with one hand and pull it upward. The Backrest Adjustment Frame (36) will automatically lock into one of the tabs on the bracket on the Bench Frame (5). T o lower the Backrest (15), grip the end of the Backrest with one hand and pull it slightly upwards. Grip the ha ...

  • Image IMBE41990 - page 16

    Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user Õs manual for information about ordering replacement parts. Key No. Qty . Description Key No. Qty . Description Part ListÑModel No. IMBE41990 R1299A 1 2 Upright 2 2 Brace 3 2 M6 x 16mm Screw 4 4 M6 x 55mm Bolt 5 1 Benc ...

  • Image IMBE41990 - page 17

    28 30 4 30 4 28 28 27 15 28 36 56 45 35 34 17 39 18 41 11 40 54 59 29 29 29 33 44 43 31 23 24 32 50 50 54 40 17 54 7 39 59 41 12 17 11 54 46 21 42 11 2 1 18 16 46 38 11 11 54 17 54 12 20 8 11 2 42 46 46 21 1 38 16 46 51 51 49 49 6 11 55 6 6 11 57 22 6 14 22 6 11 11 3 37 9 58 11 5 10 40 26 10 60 30 47 48 48 49 49 49 49 49 54 53 54 53 49 52 52 7 52 6 ...

  • Image IMBE41990 - page 18

    Part No. 160469 R1299A Printed in China © 1999 ICON Health & Fitness, Inc. T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information when cal ...

Produzent Image Kategorie Home Gym

Dokumente, die wir vom Produzenten des Geräts Image IMBE41990 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Image
- Bedienungsanleitungen IMBE41990
- Produktkarten Image
- Informationsbroschüren
- oder Energieetiketten Image IMBE41990
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Image IMBE41990.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Image IMBE41990, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Image IMBE41990. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Image IMBE41990 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Image IMBE41990, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Image IMBE41990 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Image IMBE41990 verständlich ist.

Eine gänzliche Bedienungsanleitung von Image sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Image IMBE41990 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Image IMBE41990 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Image IMBE41990, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Image IMBE41990 - die uns die ersten Schritte während der Nutzung von Image IMBE41990 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Image IMBE41990 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Image IMBE41990 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Image IMBE41990?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Image IMBE41990 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Image IMBE41990 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)