Deutsch dropdown-ico

Bedienungsanleitung Makita G1200R

26 Seiten 1.2 mb
Download

Zur Seite of 26

Summary
  • Makita G1200R - page 1

    GENERATOR MODEL : GI ZOOR INSTRUCTION MANUAL I ISSUE EMD-GU0815 I I 3229020046 I ...

  • Makita G1200R - page 2

    ...

  • Makita G1200R - page 3

    FOREWORD Thank you for purchasing this portable generator. This manual contains information and operating procedures necessary for the effective, economical and safe operation of the generator. For the proper operating procedures, read this manual thoroughly before operating the generator. For further details or questions, consult your nearest deal ...

  • Makita G1200R - page 4

    1. SAFETY PRECAUTIONS Fire prevention 0 When refueling : - Stop the engine. - Extreme care must be taken to prevent fire hazards. - Be sure to fill fuel tank up to the specified level. - Spilled fuel must be wiped off thoroughly. After (' 8 v- Avoid smoking and the use of matches or open flame. Do not overfill. spilled fuel has dried, start th ...

  • Makita G1200R - page 5

    Exhaust gas precautions -Exhaust gas contains toxic gases. Extreme care must be taken about people and - Never operate the generator indoors. - Never oprate in an enclosed area not adequately ventilated such as in a warehouse, - The exhaust pipe should be pointed toward a well-ventilated open area. domestic animals in the surrounding area. tunnel, ...

  • Makita G1200R - page 6

    2. COMPONENT IDENTIFICATION Engine control switch (CHOKE-R UN-STOP) Muffler I Ground terminal Air cleaner cover -3- ...

  • Makita G1200R - page 7

    Fuel -4- ...

  • Makita G1200R - page 8

    3. CONTROLS AND INDICATORS CHOKE RUN CHOKE 2”: To start the engine, turn the knob to this position. (Choke valve is closed.) Keep the knob in this position after the engine starts. (The engine can be started with the knob at this position when the engine is warm.) OP CLOSE FUEL OPEN v7 Fuel cock AC receptacles . I I 00 7:” 8.3A To stop the e ...

  • Makita G1200R - page 9

    AC circuit breaker DC circuit breaker 0 Both AC and DC circuit breakers shut off electric current when the current exceeds its limit or a malfunction occurs in the connected appliance. Check for excessive current consumption or defects in the appliance. After making sure everything is in order, push the button to the "ON" position. Freque ...

  • Makita G1200R - page 10

    4. BEFORE OPERATION (NECESSARY INSPECTIONS / CHECKS) Oil level checking and refilling should be performed on a level surface with the engine stopped. 3 Oil filler neck I/ / LEVELmark I I Checking engine oil level 0 Remove oil gauge and check oil level : - If level is low, fill to the top of the oil filler neck. -Change oil if badly contaminated. (S ...

  • Makita G1200R - page 11

    Checking the area around the generator - Area should be free of inflammables and hazardous materials. - The generator is placed at least 1 meter (3 ft) away from buildings or other facilities. - Generator is located in well-ventilated, open area. - The exhaust pipe is pointed toward a well-ventilated open area. - The generator is positioned away fr ...

  • Makita G1200R - page 12

    5. OPERATING PROCEDURES Starting - Check oil and fuel levels. - Make sure the appliance is disconnected. -Turn engine switch to "CHOKE" position. (When engine is warm or temperature is high, start engine with the switch at "RUN" position.) -Pull the starter handle slowly until passing the compression point (resistance will be fe ...

  • Makita G1200R - page 13

    AC application - Check the voltmeter for proper voltage. The generator is thoroughly adjusted and tested in the factory. If the generator does not produce the specified voltage, consult your nearest Generator dealer. -Check the electrical appliance to see if its switch is turned off, then connect the appliance to the generator. - Switch on the appl ...

  • Makita G1200R - page 14

    I I I DC receptacle I o Grounding the generator -To ground the generator to the earth, connect the grounding lug of the generator to the gounding spike driven into the earth or to the conductor which has been already grounded to the earth. - If such grounding conductor or grounding electrode is unavailable, connect the grounding lug of the generato ...

  • Makita G1200R - page 15

    0 Charging safety : Batteries produce explosive hydrogen gas. This gas is emitted from the vent hole of each battery cap. Safety precautions must be observed to prevent ignition and subsequent explosion of the hydrogen gas caused by open flame or sparks. - No smoking and open flame near a charging battery. - Be sure to perform the battery charging ...

  • Makita G1200R - page 16

    6. PERIODIC MAINTENANCE Fuel level Proper maintenance of the generator will allow reliable performance and reasonable maintenance cost. This section outlines a standard schedule for this purpose. This schedule should be adjusted as necessary to conform to the owner's conditions of use. Condition of engine Air cleaner Bolts and nuts oil and lev ...

  • Makita G1200R - page 17

    MAINTENANCE SCHEDULE Do-it-yourself service Check & add engine oil Clean air cleaner I Item I Interval I .... refill as required Check before each use Change engine oil Adjust spark plug gap I Clean & retighten screws I I Every 100 hours (initial : after 20 hours) Every 6 months (200 hours) Wash cleaner element Clean spark plug Every 50 hou ...

  • Makita G1200R - page 18

    7. EASY CHECKING AND MAINTENANCE Q? o I Drain plug Air cleaner servicing 0 If the air cleaner element is clogged, a decrease in generator output, erratic engine operation and / or excessive fuel consumption may result. Be sure to clean air cleaner periodically as follows : Interval : Every 50 hours or clean every day (or every 10 hours) when operat ...

  • Makita G1200R - page 19

    Checking the spark plug 0 Inspection and adjustment procedure : - Open spark plug cover. -Remove plug cap and remove spark plug using a plug wrench. -Using plug cleaner or wire brush, clean plug elec- trode of burnt or deposited carbon. - Check for proper gap between electrodes. Adjust gap to 0.6 to 0.7 mm (0.02 to 0.03 in) by bending the side elec ...

  • Makita G1200R - page 20

    8. PREPARATION FOR STORAGE - Remove fuel strainer cup, open fuel cock and completely drain fuel from tank. -After draining fuel, reinstall strainer cup and close the fuel cock. -Start and run the generator without an appliance connected until the carburetor is completely empty of fuel. - Change old lubricating oil with fresh oil. - Clean air cleane ...

  • Makita G1200R - page 21

    9. TROUBLESHOOTING Check fuel level. When engine fails to start or if the engine turns but there is no electricity at the receptacles, perform the following checks. If empty, refill fuel tank. When engine fails to start : Check to make sure that the generator is not connected to an appliance. Place engine switch to "CHOKE" position to sta ...

  • Makita G1200R - page 22

    IO. APPLICABLE WATTAGE OF THE GENERATOR Electric appliances normally come with a label indicating voltage, cycle and (input) wattage, the electric power which the appliance consumes. However, when the generator is used as the power source both power factor and starting current should be considered. HEATING RESISTANCE (Power factor 1 .O, No starting ...

  • Makita G1200R - page 23

    Applicable wattage 60Hz Appliance I Incandescent lamp,hot plate I up to 1 ooow ~ ---1 I Fluorescent lamp,mercury lamp I up to about 600W I I Electric tool I up to about 600W I I Pump,compressor I up to about 250W I NOTE : 1. Appliances equipped with electric motors. They need large starting current as mentioned above. However after starting, the ap ...

  • Makita G1200R - page 24

    11. SPECIFICATIONS 1 DESCRIPTION G1200R 1 Engine Model I EY15D (Wl -1 45) I Displacement cc lcu in Frequency HZ Rated Output Watts AC Continuous Dutv 143 I 8.73 60 1000 r OutputMax. Watts AC I Engine Speed RPM Voltage V 1200 I 3600 120 Fuel Tank Capacity : Liters Continuous Operation Hours Per Tank Ignition Automatic Voltage Regulator US Gal. I 12 ...

  • Makita G1200R - page 25

    12. WIRING DIAGRAM =’ 0 0 z t P z (7 a 3 2 Y III m 3 0 0 a (0 =! 0 z w LL IT p/ v, m W IT I --El--- IT 0 m z /! 0 E W 3 0 0 a $ IT W m z W n z 0 0 22 ...

  • Makita G1200R - page 26

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly ins ected and tested before leaving the fac- tory. It is warranted to be free of degcts from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trou- ble develop during this one-year period, return the COMPLETE tool, fre ...

Produzent Makita Kategorie Portable Generator

Dokumente, die wir vom Produzenten des Geräts Makita G1200R erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Makita
- Bedienungsanleitungen G1200R
- Produktkarten Makita
- Informationsbroschüren
- oder Energieetiketten Makita G1200R
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Makita G1200R.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Makita G1200R, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Makita G1200R. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Makita G1200R ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Makita G1200R, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Makita G1200R hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Makita G1200R verständlich ist.

Eine gänzliche Bedienungsanleitung von Makita sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Makita G1200R bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Makita G1200R befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Makita G1200R, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Makita G1200R - die uns die ersten Schritte während der Nutzung von Makita G1200R erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Makita G1200R hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Makita G1200R im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Makita G1200R?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Makita G1200R nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Makita G1200R hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)