Deutsch dropdown-ico

Bedienungsanleitung Lincoln Electric pmn

35 Seiten 1.3 mb
Download

Zur Seite of 35

Summary
  • Lincoln Electric pmn - page 1

    PO WER MIG ™ 215 OPERA TOR’S MANUAL IM828-A February, 2006 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING T ...

  • Lincoln Electric pmn - page 2

    FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors. ________________________________________________ ...

  • Lincoln Electric pmn - page 3

    ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 4.b. Use suitable clothing made from durable flame-resistant material to protect your skin ...

  • Lincoln Electric pmn - page 4

    FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations. 8.c. Ground the equipment in accordance with the U.S. National Electrical C ...

  • Lincoln Electric pmn - page 5

    iv SAFETY iv Mar. ‘93 POWER MIG 215 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1. Protegez-vous contre la secousse élec ...

  • Lincoln Electric pmn - page 6

    v v Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it handy for quick reference. Pay ...

  • Lincoln Electric pmn - page 7

    vi vi MASTER T ABLE OF CONTENTS FOR ALL SECTIONS Page ________________________________________________________________________ Installation .......................................................................................................Section A Technical Specifications ........................................................................ ...

  • Lincoln Electric pmn - page 8

    vii vii MASTER T ABLE OF CONTENTS FOR ALL SECTIONS (cont.) Page Maintenance ....................................................................................................Section D Safety Precautions ................................................................................................D-1 General Maintenance ......................... ...

  • Lincoln Electric pmn - page 9

    A-1 A-1 INST ALLA TION 75°C Copper Wire 75°C Copper Wire Input Ampere in Conduit in Conduit Input Voltage/ Fuse or Breaker Rating On AWG (IEC) Sizes AWG (IEC) Sizes (For lengths (For lengths Frequency (Hz) Size (Super Lag) Nameplate up to 100 ft.) exceeding 100 ft.) 208/50/60 60 45A 10 (6 mm 2 ) 8 (10 mm 2 ) 230/50/60 60 41A 10 (6 mm 2 ) 8 (10 mm ...

  • Lincoln Electric pmn - page 10

    A-2 A-2 INST ALLA TION Read entire installation section before starting installation. SAFETY PRECAUTIONS POWER MIG 215 INPUT POWER, GROUNDING AND CONNECTION DIAGRAMS 1. Before starting the installation, check with the local power company if there is any question about whether your power supply is adequate for the volt- age, amperes, phase, and freq ...

  • Lincoln Electric pmn - page 11

    3. The 208/230 volt 50/60 Hz model POWER MIG is shipped with a 7 ft.(2.1m). input cable and plug connected to the welder. 4. Using the instructions in Figure A.2, have a quali- fied electrician connect a receptacle (Customer Supplied) or cable to the input power lines and the system ground per the U.S. National Electrical Code and any applicable lo ...

  • Lincoln Electric pmn - page 12

    GUN AND CABLE INST ALLA TION The Magnum 250L gun and cable provided with the POWER MIG 215 is factory installed with a liner for .035-.045" (0.9-1.2 mm) electrode and an .035" (0.9 mm) contact tip. Be sure that the contact tip, liner, and drive rolls all match the size of the wire being used. Turn the welder power switch off before instal ...

  • Lincoln Electric pmn - page 13

    B-1 B-1 OPERA TION Read entire Operation section before operating the POWER MIG 215. ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet clothing. Insulate yourself from work and ground. • Always wear dry insulating gloves. FUMES AND GASES can be dangerous. • Keep your head out of fumes. • Use venti ...

  • Lincoln Electric pmn - page 14

    B-2 B-2 OPERA TION PRODUCT DESCRIPTION The POWER MIG ™ 215 is a complete semiautomatic DC voltage arc welding machine built to meet NEMA specifications. It combines a tapped transformer volt- age power source with a constant speed wire feeder to form a reliable robust performance welding system. A simple control scheme, consisting of continuous f ...

  • Lincoln Electric pmn - page 15

    B-3 B-3 OPERA TION PROCEDURE FOR CHANGING DRIVE AND IDLE ROLL SETS 1. Turn off the power source. 2. Release the pressure on the idle roll by swinging the adjustable pressure arm down toward the back of the machine. Lift the cast idle roll assembly and allow it to sit in an upright position.. 3. Remove the outside wire guide retaining plate by loose ...

  • Lincoln Electric pmn - page 16

    B-4 B-4 OPERA TION FEEDING WIRE ELECTRODE When triggering, the electrode and drive mechanism are electrically “ hot ” relative to work and ground and remain “ hot ” several seconds after the gun trigger is released. ------------------------------------------------------------------------ NOTE: Check that drive rolls, guide plates and gun pa ...

  • Lincoln Electric pmn - page 17

    B-5 B-5 OPERA TION 3. Press the trigger to feed the wire electrode through the gun and cable. For solid wire cut the electrode within approximately 3/8" (10 mm) of the end of the contact tip [3/4" (20 mm) for Outershield ® ]. 4. When welding with gas, turn on the gas supply and set the required flow rate (typically 25-35 CFH; 12- 16 lite ...

  • Lincoln Electric pmn - page 18

    B-6 B-6 OPERA TION 9. When no more welding is to be done, close valve on gas cylinder (if used), momentarily operate gun trigger to release gas pressure, and turn off POWER MIG 215. NOTE: When using Innershield electrode, the gas nozzle may be removed from the insulation on the end of the gun and replaced with the gas- less nozzle. This will give i ...

  • Lincoln Electric pmn - page 19

    C-1 C-1 ACCESSORIES DRIVE ROLL KITS Refer to Table C.1 for various drive roll kits that are available for the POWER MIG 215.The item in Bold is supplied standard with the POWER MIG 215. TABLE C.1 3/64" (1.2 mm) ALUMINUM FEEDING KIT (K1703-1) This kit helps push feeding aluminum through stan- dard machine feeder and gun. It provides gun and wir ...

  • Lincoln Electric pmn - page 20

    MAKING A WELD WITH THE SPOOL GUN ADAPTER KIT AND SPOOL GUN INST ALLED In either toggle switch position, closing either gun trigger will cause the electrode of both guns to be electrically “ HOT ” . Be sure unused gun is posi- tioned so electrode or tip will not contact metal case or other metal common to work. ---------------------------------- ...

  • Lincoln Electric pmn - page 21

    D-1 D-1 MAINTENANCE • Be sure the nozzle insulator is fully screwed onto the gun tube and does not block the gas holes in the diffuser. • Slip the appropriate gas nozzle onto the nozzle insulator. Either a standard .50" (12.7 mm) or optional .62" (15.9 mm) I.D. slip-on gas nozzle may be used and should be selected based on the welding ...

  • Lincoln Electric pmn - page 22

    D-2 D-2 MAINTENANCE 7. Screw the gas diffuser onto the end of the gun tube and securely tighten. Be sure the gas diffuser is correct for the liner being used. (See table and dif- fuser stencil.) 8. Tighten the set screw in the side of the gas diffuser against the cable liner using a 5/64" (2.0 mm) Allen wrench. FIGURE D.1 This screw should onl ...

  • Lincoln Electric pmn - page 23

    D-3 D-3 MAINTENANCE GUN HANDLE DISASSEMBL Y The internal parts of the gun handle may be inspected or serviced if necessary. The gun handle consists of two halves that are held together with a collar on each end. To open up the handle, turn the collars approxi- mately 60 degrees counterclockwise (the same direction as removing a right hand thread) u ...

  • Lincoln Electric pmn - page 24

    E-1 E-1 TROUBLESHOOTING POWER MIG 215 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed. CAUTION This Troubleshooting Guide is provided to help you locate and repair po ...

  • Lincoln Electric pmn - page 25

    E-2 E-2 TROUBLESHOOTING PROBLEMS (SYMPTOMS) Major Physical or Electrical Damage is Evident There is no wire feed or open cir- cuit voltage when the gun trigger is pulled. Input power is applied to POWER MIG 215. Output voltage and wire feed is pre- sent when gun trigger is not pulled (not activated). Machine output is low. Welds are “ cold ” , ...

  • Lincoln Electric pmn - page 26

    E-3 E-3 TROUBLESHOOTING PROBLEMS (SYMPTOMS) Poor arc striking with electrode sticking or blasting off. Auxiliary receptacle is “ dead ” - no auxiliary voltage. Rough wire feeding or wire will not feed but drive rolls are turning. POSSIBLE CAUSE 1. Make sure settings for wire feed speed and voltage are correct for process being used. 2. The gas ...

  • Lincoln Electric pmn - page 27

    E-4 E-4 TROUBLESHOOTING PROBLEMS (SYMPTOMS) The wire feed stops while welding. When trigger is released and pulled again the wire feed starts. No control of wire feed speed. Other machine functions are nor- mal. Gas does not flow when gun trigger is pulled. POSSIBLE CAUSE 1. Check the wire feed drive rolls and motor for smooth operation. 2. Check f ...

  • Lincoln Electric pmn - page 28

    F-1 F-1 WIRING DIAGRAMS NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number. POWE ...

  • Lincoln Electric pmn - page 29

    F-2 F-2 WIRING DIAGRAMS NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number. POWE ...

  • Lincoln Electric pmn - page 30

    F-3 F-3 DIMENSION PRINT 3-00F M19231 POWER MIG 215 ...

  • Lincoln Electric pmn - page 31

    NOTES POWER MIG 215 ...

  • Lincoln Electric pmn - page 32

    NOTES POWER MIG 215 ...

  • Lincoln Electric pmn - page 33

    W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES. SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL F ABRICANTE P ARA E ...

  • Lincoln Electric pmn - page 34

    W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIPAMENTO E AS P AR TES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR. ● Keep your head out of fumes. ● Use ventilation or exhaust to remove fumes ...

  • Lincoln Electric pmn - page 35

    • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com • World's Leader in Welding and Cutting Products • ...

Produzent Lincoln Electric Kategorie Welder

Dokumente, die wir vom Produzenten des Geräts Lincoln Electric pmn erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Lincoln Electric
- Bedienungsanleitungen pmn
- Produktkarten Lincoln Electric
- Informationsbroschüren
- oder Energieetiketten Lincoln Electric pmn
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Lincoln Electric pmn.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Lincoln Electric pmn, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Lincoln Electric pmn. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Lincoln Electric pmn ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Lincoln Electric pmn, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Lincoln Electric pmn hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Lincoln Electric pmn verständlich ist.

Eine gänzliche Bedienungsanleitung von Lincoln Electric sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Lincoln Electric pmn bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Lincoln Electric pmn befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Lincoln Electric pmn, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Lincoln Electric pmn - die uns die ersten Schritte während der Nutzung von Lincoln Electric pmn erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Lincoln Electric pmn hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Lincoln Electric pmn im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Lincoln Electric pmn?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Lincoln Electric pmn nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Lincoln Electric pmn hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)