Deutsch dropdown-ico

Bedienungsanleitung Husqvarna Twin YTH2546

44 Seiten 3.03 mb
Download

Zur Seite of 44

Summary
  • Husqvarna Twin YTH2546 - page 1

    03002 YTH2546 TWIN Owner's Manual ...

  • Husqvarna Twin YTH2546 - page 2

    2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine. • ...

  • Husqvarna Twin YTH2546 - page 3

    3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or ...

  • Husqvarna Twin YTH2546 - page 4

    4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ................................................................. 5-6 OPERA TION ...................................................... ...

  • Husqvarna Twin YTH2546 - page 5

    5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube AS SEMBL Y When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). TO REMOVE TRACTOR FROM CAR TON UNP ACK CARTON • Remove all accessible loose parts and parts cartons from carton. • Cut along da ...

  • Husqvarna Twin YTH2546 - page 6

    6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING? ...

  • Husqvarna Twin YTH2546 - page 7

    7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVE ...

  • Husqvarna Twin YTH2546 - page 8

    8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American Nati ...

  • Husqvarna Twin YTH2546 - page 9

    9 OPERA TION FIG. 4 TO USE CHOKE CONTROL - N (See Fig. 6) Use choke control whenever you are starting a cold engine. Do not use to start a warm engine. • T o engage choke control, pull knob out. Slowly push knob in to disengage. The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age ...

  • Husqvarna Twin YTH2546 - page 10

    10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4". The heights are measured from the ground to the blade tip with the engine not ...

  • Husqvarna Twin YTH2546 - page 11

    11 OPERA TION FIG. 11 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tracto ...

  • Husqvarna Twin YTH2546 - page 12

    12 CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sep a ra tion and for ma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. T o avoid engine problems, the fuel system should be emptied before stor age of 30 days or longer . Drain the ...

  • Husqvarna Twin YTH2546 - page 13

    13 FIG. 12 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of ...

  • Husqvarna Twin YTH2546 - page 14

    14 MAINTENANCE T R A C T 0 R I ns p e ct Muffl er /Sp ar kA rres t er Cl ean A ir F i lt er Ch an g e E n g ine O i l( w i th o i lf i lt er ) R e pl a c e A ir F i lt er P a p er C ar t ri dg e R e pl a c e Sp ar kP l u g Ch e ck E n g ine O i lL e v e l Cl ean E n g ine Cool in gF ins Cl ean A ir Sc reen 1-C h an g e mo re oft en wh en op era t i ...

  • Husqvarna Twin YTH2546 - page 15

    15 MAINTENANCE FIG. 13 02 5 4 4 MANDREL ASSEMBL Y BL ADE BL ADE BOL T (SPECIAL) CENTER HOLE ST AR BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. ? ...

  • Husqvarna Twin YTH2546 - page 16

    16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission ...

  • Husqvarna Twin YTH2546 - page 17

    17 MAINTENANCE CL AMP FUEL FIL TER FIG. 16 CLEANING • Clean engine, battery , seat, finish, etc. of all foreign matter . • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and ...

  • Husqvarna Twin YTH2546 - page 18

    18 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key . • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plu ...

  • Husqvarna Twin YTH2546 - page 19

    19 SERVICE AND ADJUSTMENTS D C G E F M A G B • A TT ACH REAR LIF T LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin (D) on rear mower bracket and secure with washer and retainer spring. • Install belt on engine pulley (M), in belt keepers (G). IMPORT ANT : CHECK BEL T FOR PROPER ROUTING IN ALL MOWER PULLEY GROOV ...

  • Husqvarna Twin YTH2546 - page 20

    20 SERVICE AND ADJUSTMENTS • If adjustment is necessary , see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT - TO-BACK ADJUSTMENT (See Figs. 24 and 25) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adju ...

  • Husqvarna Twin YTH2546 - page 21

    21 SERVICE AND ADJUSTMENTS FIG. 26 TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 26) • P ark tractor on a level surface. Engage parking brake. • Remove screws from L.H. mandrel cover and remove cover . • Roll belt over the top of L.H. mandrel pulley . • Remove belt from electric clutch pulley . • Remove belt from idler pulleys. • Remov ...

  • Husqvarna Twin YTH2546 - page 22

    22 SERVICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REP AIRS (See Fig. 28) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). FRONT WHEEL TOE-IN/CAM BER Y our new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel ...

  • Husqvarna Twin YTH2546 - page 23

    23 SERVICE AND ADJUSTMENTS TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 29) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BA TTER ...

  • Husqvarna Twin YTH2546 - page 24

    24 SERVICE AND ADJUSTMENTS TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERL OCKS AND REL A YS Loose or damaged wiring may cause your tractor to run poorly , sto ...

  • Husqvarna Twin YTH2546 - page 25

    25 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Husqvarna Twin YTH2546 - page 26

    26 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Weak or dead battery . 5. Recharge or replace battery . 6. Dirty air ...

  • Husqvarna Twin YTH2546 - page 27

    27 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged. Engine continues to run 1. Faulty operator -safety presence control system. 1. Check wiring, switc ...

  • Husqvarna Twin YTH2546 - page 28

    28 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES 1 532 05 91-92 Cap, V alve, Tire 2 532 06 51-39 Stem, V alve 3 532 13 83-36 Rim Assembly , Front 4 532 05 99- ...

  • Husqvarna Twin YTH2546 - page 29

    29 M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOUR METER REGULA TOR CHASSIS HARNESS CONNECT OR (MA TING SIDE) D ASH HARNESS CONNECT OR (MA TING SIDE) LIGHT SWITCH HEADLIGHTS S TAT O R FUEL LINE FUEL SHUT -O ...

  • Husqvarna Twin YTH2546 - page 30

    30 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 ELECTRICAL 30 33 24 42 40 26 2 8 71 194276D 29 34 43 25 27 41 50 22 21 46 46 90 101 Battery _28 8 1 99 100 91 2 27 102 16  101 104 55 ...

  • Husqvarna Twin YTH2546 - page 31

    31 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 14 49-27 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 Battery Box 16 532 17 61-38 Switch Interlock 21 532 18 37-59 Harness Socket Light 22 532 00 41-52 Bulb, Light # 1156 24 532 40 02-53 Cable Battery 25 ...

  • Husqvarna Twin YTH2546 - page 32

    32 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 CHASSIS 1 8 2 6 8 6 8 176 176 176 175 17 8 22 8 22 8 1 8 3 194 236 150 1 8 0 6 8 6 8 213 213 52 21 8 34 130 130 177 chassis-te x_61-gt-husq 189 189 152 217 99 235 37 194 194 1 8 1 1 8 1 161 36 36 199 162 196 221 162 5 8 1 8 9 1 8 9 14 214 130 130 202 203 204 210 20 8 1 8 15 ...

  • Husqvarna Twin YTH2546 - page 33

    33 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 CHASSIS 3 532 40 50-12 Logo 5 532 40 87-01 Dash 14 532 41 10-46 Hood 15 532 19 89-07 Lens LH 18 532 40 86-07 Grille Asm. 25 532 19 89-06 Lens RH 34 532 19 61-25 Plate Engine 36 817 06 05-12 Screw 5/16-18 x 3/4 37 532 40 18-25 F ender 52 873 68 05-00 Nut Lock 5/16-18 58 532 ...

  • Husqvarna Twin YTH2546 - page 34

    34 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 DRIVE                               ? ...

  • Husqvarna Twin YTH2546 - page 35

    35 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - - - - T ransaxle, TUFF TORQ K46 (Internal parts not available) 2 532 12 35-83 K ey 1/4 x 2.5 15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga. 17 532 41 36-78 Spring, Brake 26 532 19 96-79 Sprin ...

  • Husqvarna Twin YTH2546 - page 36

    36 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 ENGINE NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 Kohler Co. 1-800-544-2444 T ecumseh Products 1-800 ...

  • Husqvarna Twin YTH2546 - page 37

    37 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 STEERING ASSEMBL Y 6 5 13 13 53 8 9 9 8 8 7 7 62 4 35 16 19 63 63 57 60 59 58 28 13 22 64 70 68 69 67 67 66 15 15 14 14 21 51 26 1 45 61 2 6 steering-tex_9-husq KEY P ART NO . NO . DESCRIPTION 1 532 19 36-51 Wheel, Steering 2 532 19 59-68 Axle Asm., F ront 4 532 40 30-87 Sp ...

  • Husqvarna Twin YTH2546 - page 38

    38 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 MOWER DECK 30 55 30 32 31 33 56 34 57 59 240 129 1 88 1 69 69 69 199 40 3 46 145 46_te x-lt_pred_4 15 14 13 11 8 21 25 26 27 19 8 29 21 21 23 24 36 40 2 19 19 6 6 117 116 11 8 119 117 119 116 11 8 6 8 46 1 8 9 1 8 9 1 88 21 21 69 69 69 21 30 241 147 ...

  • Husqvarna Twin YTH2546 - page 39

    39 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 MOWER DECK KEY P ART NO . NO . DESCRIPTION 1 532 41 14-60 Mower Housing 2 532 40 55-07 Cover Mandrel LH 3 532 40 55-06 Cover Mandrel RH 6 532 19 51-86 Arm Suspension 8 532 19 30-03 Bolt/Washer asm 7/16-20 unf 11 532 40 53-80 Blade Mower 13 532 19 28-72 Shaft Assembly , Mand ...

  • Husqvarna Twin YTH2546 - page 40

    40 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 SEA T ASSEMBL Y 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock W/Ins. 3/8-16 unc 7 532 12 41-81 Spring, Seat Cprsn 8 532 17 18-77 Bolt 5/16-18 uncx 3/4 w/Sems 10 532 19 69-77 P an, Seat 21 532 17 18-52 Bolt, ...

  • Husqvarna Twin YTH2546 - page 41

    41 TRACTOR - MODEL NO . YTH2546 TWIN(96041005500), PRODUCT NO. 960 41 00-55 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 lift-tex_5 91 89 87 100 2 532 19 52-23 Shaft Asm., Lift 3 532 19 52-30 Lever Asm., Lift 7 532 41 15-55 Grip, Lever 10 532 19 63-14 Spring T orsion 87 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock 88 532 19 53-04 Spring Lift Assist 89 ...

  • Husqvarna Twin YTH2546 - page 42

    42 SERVICE NOTES ...

  • Husqvarna Twin YTH2546 - page 43

    43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Husqvarna Twin YTH2546 - page 44

    532 41 06-05 Rev . 3 05.10.07 AP Printed in U.S.A. ...

Produzent Husqvarna Kategorie Lawn Mower

Dokumente, die wir vom Produzenten des Geräts Husqvarna Twin YTH2546 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Husqvarna
- Bedienungsanleitungen Twin YTH2546
- Produktkarten Husqvarna
- Informationsbroschüren
- oder Energieetiketten Husqvarna Twin YTH2546
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Husqvarna Twin YTH2546.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Husqvarna Twin YTH2546, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Husqvarna Twin YTH2546. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Husqvarna Twin YTH2546 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Husqvarna Twin YTH2546, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Husqvarna Twin YTH2546 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Husqvarna Twin YTH2546 verständlich ist.

Eine gänzliche Bedienungsanleitung von Husqvarna sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Husqvarna Twin YTH2546 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Husqvarna Twin YTH2546 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Husqvarna Twin YTH2546, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Husqvarna Twin YTH2546 - die uns die ersten Schritte während der Nutzung von Husqvarna Twin YTH2546 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Husqvarna Twin YTH2546 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Husqvarna Twin YTH2546 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Husqvarna Twin YTH2546?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Husqvarna Twin YTH2546 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Husqvarna Twin YTH2546 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)