Deutsch dropdown-ico

Bedienungsanleitung Sun Microsystems FC-100

38 Seiten 0.61 mb
Download

Zur Seite of 38

Summary
  • Sun Microsystems FC-100 - page 1

    901 San Antonio Road Palo Alto, CA 94303-4900 USA 650 960-1300 Fax 650 969-9131 Sun ™ StorEdge ™ FC-100 Hub Installation and Service Manual Formerly the Sun ™ Enterprise Network Array ™ Part No. 805-0315-12 September 1998, Revision A Sun Microsystems, Inc. Send comments about this document to: docfeedback@sun.com ...

  • Sun Microsystems FC-100 - page 2

    Copyright 1998 Sun Microsystems, Inc. 901 San Antonio Road • Palo Alto, CA 94303 USA. All rights reserved. This product or document is protected by copyright and distributed under licenses restricting its use, copying, distribution, and decompilation. No part of this product or document may be repr oduced in any form by any means without prior wr ...

  • Sun Microsystems FC-100 - page 3

    Regulatory Compliance Statements iii Regulatory Compliance Statements Your Sun product is marked to indicate its compliance class: • Federal Communications Commission (FCC) — USA • Department of Communications (DOC) — Canada • V oluntary Control Council for Interfer ence (VCCI) — Japan Please read the appropriate section that correspond ...

  • Sun Microsystems FC-100 - page 4

    iv Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 DOC Class A Notice - A vis DOC, Classe A This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Can ...

  • Sun Microsystems FC-100 - page 5

    Safety Agency Compliance Statements v Safety Agency Compliance Statements Read this section before beginning any pr ocedure. The following text provides safety pr ecautions to follow when installing a Sun Microsystems pr oduct. Safety Precautions For your protection, observe the following safety pr ecautions when setting up your equipment: • Foll ...

  • Sun Microsystems FC-100 - page 6

    vi Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 Caution – Do not operate Sun products without the top cover in place. Failure to take this pr ecaution may result in personal injury and system damage. Laser Compliance Notice Sun products that use laser technology comply with Class 1 laser requir ements. Einhaltung sic ...

  • Sun Microsystems FC-100 - page 7

    Safety Agency Compliance Statements vii Achtung – Nicht alle Netzkabel haben die gleichen Nennwerte. Herkömmliche, im Haushalt verwendete V erlängerungskabel besitzen keinen Überlastungsschutz und sind daher für Computersysteme nicht geeignet. Achtung – Ihr Sun-Gerät wird mit einem dr eiadrigen Netzkabel für geerdete Netzsteckdosen gelief ...

  • Sun Microsystems FC-100 - page 8

    viii Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 Modification du matériel Ne pas apporter de modification mécanique ou électrique au matériel. Sun Microsystems n’est pas responsable de la conformité réglementaire d’un pr oduit Sun qui a été modifié. Positionnement d’un produit Sun Attention : pour assur ...

  • Sun Microsystems FC-100 - page 9

    Safety Agency Compliance Statements ix • No introduzca nunca objetos de ningún tipo a través de los orificios del equipo. Pueden haber voltajes peligr osos. Los objetos extraños conductores de la electricidad pueden producir cortocir cuitos que provoquen un incendio, descargas eléctricas o daños en el equipo. Símbolos En este libro apar ece ...

  • Sun Microsystems FC-100 - page 10

    x Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 Precaución – Es peligroso hacer funcionar los productos Sun sin la tapa superior colocada. El hecho de no tener en cuenta esta precaución puede ocasionar daños personales o perjudicar el funcionamiento del equipo. A viso de cumplimiento con requisitos de láser Los pr ...

  • Sun Microsystems FC-100 - page 11

    xi Declaration of Conformity Compliance ID: HUB 1063 Product Name: Sun StorEdge FC-100 Hub This product has been tested and complies with; EMC European Union-EC This equipment complies with the following requirements of the EMC Directive 89/336/EEC EN55022 / CISPR22 (1985) Class A EN50082-1 IEC801-2 (1991) 4 kV (Direct), 8 kV (Air) IEC801-3 (1984) ...

  • Sun Microsystems FC-100 - page 12

    xii Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 ...

  • Sun Microsystems FC-100 - page 13

    Contents xiii Contents Preface xv 1. Product Description 1- 1 1.1 Sun StorEdge FC-100 Hub 1- 1 1.2 GBIC 1-3 2. Installation 2-1 2.1 Inspecting the Hub 2-1 2.2 Rackmount Placement 2-1 2.3 Installing the Hub 2-2 2.3.1 T ools Y ou W ill Need 2-2 2.3.2 Preparing the Cabinet 2-2 2.3.3 Installing the Mounting T ray in the Cabinet 2-2 2.3.4 Installing the ...

  • Sun Microsystems FC-100 - page 14

    xiv Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 3.1 Installing a GBIC 3-1 3.2 Removing a GBIC 3-4 3.3 Removing a Hub 3-6 A. Specif ications A-1 ...

  • Sun Microsystems FC-100 - page 15

    xv Pr eface The Sun StorEdge FC-100 Hub Installation and Service Manual provides information on installing and servicing the Sun™ StorEdge™ FC-100 Hub. These instructions are designed for an experienced system administrator or trained service provider . Using UNIX Commands This document does not contain information on basic UNIX ® commands and ...

  • Sun Microsystems FC-100 - page 16

    xvi Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 T ypographic Conventions Shell Pr ompts T ABLE P-1 T ypographic Conventions T ypeface Meaning Examples AaBbCc123 The names of commands, files, and directories; on-scr een computer output Edit your .login file. Use ls -a to list all files. % You have mail . AaBbCc123 What ...

  • Sun Microsystems FC-100 - page 17

    Preface xvii Related Documentation Refer to the Sun StorEdge A5000 Disk Array Installation and Documentation Guide , part number 805-1903-xx, for a list of related documentation Sun Documentation on the W eb The docs.sun.com sm web site enables you to access Sun technical documentation on the W eb. Y ou can browse the docs.sun.com archive or sear c ...

  • Sun Microsystems FC-100 - page 18

    xviii Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 ...

  • Sun Microsystems FC-100 - page 19

    1-1 CHAPTER 1 Pr oduct Description This chapter describes the Sun StorEdge FC-100 Hub and Gigabit Interface Converters (GBICs). 1.1 Sun StorEdge FC-100 Hub The hub is a seven-port connection point for Fibre Channel Arbitrated Loops (FC-ALs). Ports are connected using GBICs. Each port r eceives serial data from a remote node and r etransmits that da ...

  • Sun Microsystems FC-100 - page 20

    1-2 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 Data transfer within the hub is implemented in serial differential Positive Emitter Coupled Logic (PECL) AC coupled logic. Each port monitors the serial data input stream as well as the media converter connected to it. Initiators or targets on the loop r epresent individ ...

  • Sun Microsystems FC-100 - page 21

    Chapter 1 Product Descr iption 1-3 1.2 GBIC The GBIC is compliant with Fibre Channel FC-PH-2 physical layer option 100-M5- SN-I and the ANSI FC-AL standard. The full speed of the module is 1062.5 Mbits/ second. The range of distances supported is 2 to 500 meters. Sun currently ships two types of GBICs: one with a bailed locking mechanism and one wi ...

  • Sun Microsystems FC-100 - page 22

    1-4 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 ...

  • Sun Microsystems FC-100 - page 23

    2-1 CHAPTER 2 Installation This chapter describes how to install the hub in a cabinet. 2.1 Inspecting the Hub 1. Unpack the hub. 2. Inspect the hub for evidence of damage. If damaged, keep all contents and packing materials for the carrier ’s agent to inspect. 3. Save the packing materials for future use. 2.2 Rackmount Placement Rackmount placeme ...

  • Sun Microsystems FC-100 - page 24

    2-2 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 2.3 Installing the Hub 2.3.1 T ools Y ou W ill Need Y ou will need a #2 Phillips screwdriver . 2.3.2 Pr eparing the Cabinet Follow the instruction in your system or expansion cabinet documentation. If necessary , be sure to: ■ Extend the antitilt bar ■ Remove or open ...

  • Sun Microsystems FC-100 - page 25

    Chapter 2 Installation 2-3 2. Install the tray in the cabinet ( FIGURE 2-1 ). FIGURE 2-1 Installing the T ray in the Cabinet Caution – Use only SAE 10-32 screws to secur e the tray to the cabinet mounting rails. Using any other screw type will damage the cabinet mounting holes. a. In the front of the tray , use the Phillips screwdriver to loosely ...

  • Sun Microsystems FC-100 - page 26

    2-4 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 2.3.4 Installing the Hub on the Mounting T ray 1. Determine on which side of the tray you are going to install the hub . The first hub goes in position A; the second goes in position B. 2. From the rear of the tray , slide the hub mounting bracket into the slots in the m ...

  • Sun Microsystems FC-100 - page 27

    Chapter 2 Installation 2-5 2.3.5 Installing GBICs and Fiber Optic Cables 1. Choose the hub port into which you will install the GBIC. Although the ports in a hub are electrically equivalent, follow any configuration guidelines that may have accompanied the other hardware in your configuration. If you are connecting the GBIC to a Sun StorEdge A5000 ...

  • Sun Microsystems FC-100 - page 28

    2-6 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 ■ T o insert a GBIC that has a bail, slide the GBIC into the available port with the bail in the unlocked (right) position. Once the GBIC is firmly seated in the port, move the bail left into the locked position. FIGURE 2-4 Installing a GBIC That Has a Bail and Fiber O ...

  • Sun Microsystems FC-100 - page 29

    Chapter 2 Installation 2-7 1. Connect the female end of the power cord to the power receptacle at the rear of the hub ( FIGURE 1- 1 on page 1-2). 2. Route the power cord down the right side and along the bottom of the cabinet. 3. Route the power cord up through the cutout to the power distribution unit at the left side of the cabinet. Caution – T ...

  • Sun Microsystems FC-100 - page 30

    2-8 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 2.3.8 Reassembling the Cabinet Follow the instructions in your system or expansion cabinet documentation. If necessary , be sure to: ■ Replace or close the top front panel ■ Replace or close the rear panel ■ Push the antitilt bar back into the cabinet 2.4 T r ouble ...

  • Sun Microsystems FC-100 - page 31

    3-1 CHAPTER 3 Service This chapter describes how to remove and install a GBIC. It also describes how to remove a hub. 3.1 Installing a GBIC 1. Choose the hub port into which you will install the GBIC. Although the ports in a hub are electrically equivalent, follow any configuration guidelines that may have accompanied the other hardware in your con ...

  • Sun Microsystems FC-100 - page 32

    3-2 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 ■ T o insert a GBIC that does not have a bail, slide the GBIC into the port until you hear a click. FIGURE 3-1 Installing a GBIC That Does Not Have a Bail ...

  • Sun Microsystems FC-100 - page 33

    Chapter 3 Ser vice 3-3 ■ T o insert a GBIC that has a bail, slide the GBIC into the available port with the bail in the unlocked (right) position. Once the GBIC is firmly seated in the port, move the bail left into the locked position. FIGURE 3-2 Installing a GBIC That Has a Bail 3. Connect the f iber optic cable to the GBIC. Slot Bail ...

  • Sun Microsystems FC-100 - page 34

    3-4 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 3.2 Removing a GBIC 1. Disconnect the f iber optic cable from the GBIC ( FIGURE 3-3 or FIGURE 3-4 ). 2. Remove the GBIC. Sun currently ships two types of GBICs: one with a bailed locking mechanism and one without. ■ T o remove a GBIC that does not have a bail, push the ...

  • Sun Microsystems FC-100 - page 35

    Chapter 3 Ser vice 3-5 ■ T o remove a GBIC that has a bail, move the bail right to the unlocked position and pull on the plastic tab of the bail. FIGURE 3-4 Removing a GBIC That Has a Bail Ta b ...

  • Sun Microsystems FC-100 - page 36

    3-6 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 3.3 Removing a Hub 1. Disconnect and remove any installed f iber optic cables or GBICs ( FIGURE 3-3 ). 2. Disconnect the AC power cord from the hub. 3. Push up on the retaining tab that secures the hub to the mounting tray ( FIGURE 3-5 ). FIGURE 3-5 Removing the Hub 4. P ...

  • Sun Microsystems FC-100 - page 37

    A-1 APPENDIX A Specif ications A.1 Physical T ABLE A-1 Physical Specifications Height Width Depth Weight 1.69 in 8.6 in 14.35 in 6 lbs 42.92 mm 218.4 mm 364.49 mm 2.72 kg ...

  • Sun Microsystems FC-100 - page 38

    A-2 Sun StorEdge FC-100 Hub Installation and Service Manual • September 1998 A.2 Electrical A.3 Envir onmental T ABLE A-2 Electrical Specifications Specification V alue V oltage 95 to 120V Frequency 50 to 60 Hz Power Consumption Empty Full 25W 35W 1 Line Current A verage Surge (Peak) 350 mA 1 1.0 A ( < 1 second) 1 1. All ports in use @250 mA e ...

Produzent Sun Microsystems Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts Sun Microsystems FC-100 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Sun Microsystems
- Bedienungsanleitungen FC-100
- Produktkarten Sun Microsystems
- Informationsbroschüren
- oder Energieetiketten Sun Microsystems FC-100
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Sun Microsystems FC-100.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Sun Microsystems FC-100, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Sun Microsystems FC-100. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Sun Microsystems FC-100 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Sun Microsystems FC-100, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Sun Microsystems FC-100 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Sun Microsystems FC-100 verständlich ist.

Eine gänzliche Bedienungsanleitung von Sun Microsystems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Sun Microsystems FC-100 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Sun Microsystems FC-100 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Sun Microsystems FC-100, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Sun Microsystems FC-100 - die uns die ersten Schritte während der Nutzung von Sun Microsystems FC-100 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Sun Microsystems FC-100 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Sun Microsystems FC-100 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Sun Microsystems FC-100?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Sun Microsystems FC-100 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Sun Microsystems FC-100 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)