Bedienungsanleitung Juniper Networks MX960

16 Seiten 0.75 mb
Download

Zur Seite of 16

Summary
  • Juniper Networks MX960 - page 1

    MX960 Ethernet Services Router DC Power Supply Installation Instructions 19 October 2007 Part Number: 530-017577-01 Revision 2 This document describes how to remove and replace a DC power supply on a Juniper Networks MX960 Ethernet Services Router. Contents DC Power Supply ............................................................................ ...

  • Juniper Networks MX960 - page 2

    DC Power Supply In the DC power configuration, the router contains either two or four DC power supplies (see Figure 1 on page 2), located at the lower rear of the chassis in slots PEM0 through PEM3 (left to right). You can upgrade your DC power system from two to four power supplies. The DC power supplies in slots PEM0 and PEM2 provide power to the ...

  • Juniper Networks MX960 - page 3

    Table 1: DC Power Supply Electrical Specifications Specification Item 2800 W Maximum output power Minimum: – 40 VDC Nominal: – 48 VDC Operating range: – 40 to – 72 VDC NOTE: If the input voltage from the DC power source drops below -37.5 to -39.5 VDC, the routing platform automatically shuts down. During automatic shutdown, the circuit rema ...

  • Juniper Networks MX960 - page 4

    Replacing a DC Power Supply To replace a DC power supply, use the following procedures: ■ Removing a DC Power Supply on page 4 ■ Installing a DC Power Supply on page 7 Removing a DC Power Supply The power supplies are located at the rear of the chassis. Each DC power supply weighs approximately 3.8 lb (1.7 kg). CAUTION: Do not leave a power sup ...

  • Juniper Networks MX960 - page 5

    Figure 2: Disconnecting Power Cables From the DC Power Supply 6. Remove the cable lugs from the terminal studs. 7. Loosen the captive screw on the cable restraint on the lower edge of the power supply faceplate. 8. Carefully move the power cables out of the way. 9. While grasping the handle on the power supply faceplate with one hand, use your othe ...

  • Juniper Networks MX960 - page 6

    Figure 3: Removing a DC Power Supply Figure 4: Top of the Power Supply Showing Midplane Connector 6 ■ Replacing a DC Power Supply MX960 Ethernet Services Router DC Power Supply Installation Instructions ...

  • Juniper Networks MX960 - page 7

    Installing a DC Power Supply To install a DC power supply, follow this procedure (see Figure 5 on page 9): 1. Ensure that the voltage across the DC power source cable leads is 0 V and that there is no chance that the cable leads might become active during installation. CAUTION: You must ensure that power connections maintain the proper polarity. Th ...

  • Juniper Networks MX960 - page 8

    ■ Attach the positive (+) DC source power cable lug to the RTN (return) terminal. ■ Attach the negative ( – ) DC source power cable lug to the – 48V (input) terminal. NOTE: The DC power supplies in slots PEM0 and PEM1 must be powered by dedicated power feeds derived from feed A , and the DC power supplies in slots PEM2 and PEM3 must be powe ...

  • Juniper Networks MX960 - page 9

    Figure 5: Installing a DC Power Supply Replacing a DC Power Supply ■ 9 Replacing a DC Power Supply ...

  • Juniper Networks MX960 - page 10

    Figure 6: Connecting DC Power to the Router List of Technical Publications Table 3 on page 10 lists the software and hardware guides and release notes for Juniper Networks J-series, M-series, MX-series, and T-series routing platforms and describes the contents of each document. Table 4 on page 15 lists the books included in the Network Operations G ...

  • Juniper Networks MX960 - page 11

    Table 3: Technical Documentation for Supported Routing Platforms (continued) Description Book Describes how to use the JUNOS command-line interface (CLI) to configure, monitor, and manage Juniper Networks routing platforms. This material was formerly covered in the JUNOS System Basics Configuration Guide . CLI User Guide Provides a detailed explana ...

  • Juniper Networks MX960 - page 12

    Table 3: Technical Documentation for Supported Routing Platforms (continued) Description Book Provides an overview and describes how to configure Layer 2 and Layer 3 virtual private networks (VPNs), virtual private LAN service (VPLS), and Layer 2 circuits. Provides configuration examples. VPNs JUNOS References Describes the JUNOS configuration mode ...

  • Juniper Networks MX960 - page 13

    Table 3: Technical Documentation for Supported Routing Platforms (continued) Description Book Describes how to use the commit script and self-diagnosis features of the JUNOS software. This guide explains how to enforce custom configuration rules defined in scripts, how to use commit script macros to provide simplified aliases for frequently used co ...

  • Juniper Networks MX960 - page 14

    Table 3: Technical Documentation for Supported Routing Platforms (continued) Description Book Describes the JUNOScope software graphical user interface (GUI), how to install and administer the software, and how to use the software to manage routing platform configuration files and monitor routing platform operations. JUNOScope Software User Guide A ...

  • Juniper Networks MX960 - page 15

    Table 3: Technical Documentation for Supported Routing Platforms (continued) Description Book Summarize new features for a particular release, identify known hardware and software problems, provide information that might have been omitted from the manuals, and provide upgrade and downgrade instructions. JUNOS Enhanced Services Release Notes Table 4 ...

  • Juniper Networks MX960 - page 16

    Table 5: Additional Books Available Through http://www.juniper.net/books (continued) Description Book Provides an overview of Multiprotocol Label Switching (MPLS) applications (such as Layer 3 virtual private networks [VPNs], Layer 2 VPNs, virtual private LAN service [VPLS], and pseudowires), explains how to apply MPLS, examines the scaling require ...

Produzent Juniper Networks Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts Juniper Networks MX960 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Juniper Networks
- Bedienungsanleitungen MX960
- Produktkarten Juniper Networks
- Informationsbroschüren
- oder Energieetiketten Juniper Networks MX960
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Juniper Networks MX960.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Juniper Networks MX960, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Juniper Networks MX960. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Juniper Networks MX960 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Juniper Networks MX960, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Juniper Networks MX960 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Juniper Networks MX960 verständlich ist.

Eine gänzliche Bedienungsanleitung von Juniper Networks sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Juniper Networks MX960 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Juniper Networks MX960 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Juniper Networks MX960, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Juniper Networks MX960 - die uns die ersten Schritte während der Nutzung von Juniper Networks MX960 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Juniper Networks MX960 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Juniper Networks MX960 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Juniper Networks MX960?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Juniper Networks MX960 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Juniper Networks MX960 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)