Deutsch dropdown-ico

Bedienungsanleitung JVC RX-F31S

153 Seiten 6.32 mb
Download

Zur Seite of 153

Summary
  • JVC RX-F31S - page 1

    English LVT1306-009B [US] RX-F31S INSTR UCTIONS HOME CINEMA CONTROL CENTER cover_RX-F31S[US]ff.p65 05.6.9, 17:01 3 ...

  • JVC RX-F31S - page 2

    G-1 RX-F31S W arnings, Cautions, and Other s / Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely . The ST ANDBY/ON button in an y position does not disconnect the mains line. The power can be remote controlled. CA UTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remov e screws, cov ers o ...

  • JVC RX-F31S - page 3

    1 English Ta b le of Contents Pa r ts identification ................................................ 2 Getting started ...................................................... 4 Before Installation .................................................................. 4 Checking the supplied accessories ....................................... 4 Putting ...

  • JVC RX-F31S - page 4

    2 English SET HOME CINEMA CONTROL CENTER REMOTE CONTR OL RM - SRXF31U 4 2 t 3 1 5 9 8 7 q w e r u y i o p 6 Remote control See pages in parentheses f or details. 1 TV DIRECT button (14) 2 Source selecting buttons (12, 14, 32, 33) D VR/D VD , VCR, DBS , TV , D VD MUL TI, FM/AM 3 Operating buttons f or tuner (32, 33) ( TUNING, FM MODE, TUNING 9 , MEM ...

  • JVC RX-F31S - page 5

    3 English Front panel 1 ST ANDBY/ON button and standby lamp (12, 14, 32) 2 Source lamps D VD MUL TI, D VR/D VD , VCR, DBS , TV , FM/AM 3 • SOURCE SELECT OR (12, 14, 33) • MUL TI JOG (18, 26, 33, 39) 4 MASTER VOLUME control (13) 5 PHONES jack (13) 6 TV DIRECT button (14) 7 SETTING button (18, 32) 8 ADJUST button (26, 32) 9 SURROUND b utton (39) ...

  • JVC RX-F31S - page 6

    4 English Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–). 3 Replace the cover . If the range or eff ectiveness of the remote control ...

  • JVC RX-F31S - page 7

    5 English 110V 127V 220V 230 - 240V ANTENNA AM LOOP AM EXT COAXIAL FM 75 ANTENNA Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed. AM loop antenna (supplied) If AM reception is poor, connect ...

  • JVC RX-F31S - page 8

    6 English LR LS RS SB C SW 110V 127V 220V 230 - 240V CAUTION:SPEAKER IMPEDANCE 6 – 16 CENTER SURROUND SURROUND BACK SPEAKERS LEFT RIGHT LEFT RIGHT FRONT LINK- III OUT SUB- WOOFER AV COMPU Connecting the speakers T urn off all components before making connections. 1 T wist and remove the insulation at the end of eac h speaker cord. 2 Press and hol ...

  • JVC RX-F31S - page 9

    7 English This receiver is equipped with the f ollowing video terminals— composite video , S-video, and component video terminals. • If your video components ha ve S-video (Y/C-separation) and/or component video (Y , P B , P R ) jacks , connect them using an S- video cable (not supplied) or component video cab le (not supplied). By using these ...

  • JVC RX-F31S - page 10

    8 English 110V 127V 220V 230 - 240V VIDEO VCR OUT (REC) Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT DVR/DVD IN (PLAY) DVR OUT (REC) S-VIDEO VCR OUT (REC) DVR OUT (REC) DVR/DVD IN (PLAY) AUDIO SURR-L SURR-R CENTER SUBWOOFER DVD MULTI IN Å ı Ç Î ‰ Ì Ó È Ô Ï 7 Connecting a D VD recorder or D VD player with its analog discrete output j ...

  • JVC RX-F31S - page 11

    9 English 110V 127V 220V 230 - 240V TV VCR DBS IN IN IN (PLAY) DBS IN VCR MONITOR OUT IN (PLAY) Å ı Ç 110V 127V 220V 230 - 240V VCR DBS IN IN (PLAY) OUT (REC) DVR/DVD IN (PLAY) Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT DBS IN VCR OUT (REC) IN (PLAY) DVR/DVD IN (PLAY) ‰ ÏÌ Î Ç Å ı 7 Connecting a VCR Å To left/right audio channel ...

  • JVC RX-F31S - page 12

    10 English 110V 127V 220V 230 - 240V L R TV DBS IN IN MONITOR OUT OUT SUB- WOOFER DBS IN MONITOR OUT Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT Å ı Ç Î ‰ 7 Connecting a TV Connect the TV to the appropr iate MONIT OR OUT jacks to vie w the pla yback picture from an y other connected video components. Stereo audio cable (not supplied) Re ...

  • JVC RX-F31S - page 13

    11 English 110V 127V 220V 230 - 240V PCM/ STREAM DIGITAL OUT 110V 127V 220V 230 - 240V DIGITAL IN 3(VCR) 2(DBS) 1(DVR/DVD) NO TES • When shipped from the f actory , the DIGIT AL IN ter minals hav e been set f or use with the f ollowing components: – 1(D VR/D VD): F or D VD recorder or D VD play er – 2(DBS): For DBS tuner – 3(VCR): F or VCR ...

  • JVC RX-F31S - page 14

    12 English Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECT OR until the source name y ou want appear s on the display . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECT OR, the source changes as f ollo ws: D VD MUL TI: Select for the D VD player using the analog d ...

  • JVC RX-F31S - page 15

    13 English 3 Adjust the volume To increase the volume, turn MASTER V OLUME control c lockwise (or press V OLUME + on the remote control). To decrease the v olume, turn MASTER V OLUME control counter clockwise (or press V OLUME – on the remote control). • When you adjust the v olume, the volume le vel indication appears on the displa y for a whi ...

  • JVC RX-F31S - page 16

    14 English Adjusting the subwoofer audio position If the subwoof er sound is much reinforced f or stereo sound compared to the sound reproduced with multi-channel, set the subwoof er audio position. The subwoofer output le vel is automatically decreased by the selected v alue when you are listening in stereo . The A UDIO P . indicator lights up whe ...

  • JVC RX-F31S - page 17

    15 English Tu rning off the sounds temporarily From the remote control ONL Y : Press MUTING to turn off the sound through all connected speakers and headphones. “MUTING” appears on the display and the v olume tur ns off. To restore the sound, press MUTING again. • Pressing VOLUME +/– (or turning MASTER VOLUME control on the front panel) als ...

  • JVC RX-F31S - page 18

    16 English From the remote control ONL Y : 1 T ake your position where y ou listen to the sound. • Make sure speak er cables are connected fir mly . 2 Press and hold SMART SURR OUND SETUP until “SETTING UP” flashes. *1 L: Left front speaker *2 C: Center speaker *3 R: Right front speaker *4 RS: Right surround speaker *5 SB: Surround back speak ...

  • JVC RX-F31S - page 19

    17 English When your c lapping sound is detected successfully , • On the TV screen, “SUCCESSFUL, ” “RESUL T , ” and the setting v alues appear . The setting values are shown f or about 12 seconds. Ex.: • On the display , “SUCCESSFUL ” appears, then the setting values are sho wn as follows f or about 12 seconds: Ex.: *7 Standard chan ...

  • JVC RX-F31S - page 20

    18 English Basic setting items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting. •T he name of the item shown below is the on-screen displa y indication and the name in parentheses is the display indication. * If you ha ve used Smar t Surro ...

  • JVC RX-F31S - page 21

    19 English FL SPK DISTANCE TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT SETTING MENU (1) 5 SUBWOOFER : NO FRONT SPK : LARGE CENTER SPK : SMALL SURR. SPK : SMALL SURR. BACK SPK : SMALL ∞ :ENTER :TOP MENU SETTING MENU (2) 5 DISTANCE UNIT :meter FL SPK DISTANCE : 3.0m FR SPK DISTANCE : 3.0m C SPK DISTANCE : 3.0m LS SPK DISTANCE : 3.0m RS SPK ...

  • JVC RX-F31S - page 22

    20 English DIGITAL IN 1 DIGITAL IN 1: 2 DVR/DVD 3 23 :OPERATE :BACK TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 25). Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. I ...

  • JVC RX-F31S - page 23

    21 English 4 Press SET . 5 To select the appropriate setting, press 2 or 3 repeatedly , then press SET . The on-screen display returns to the pre vious SETTING MENU . In this example, “SETTING MENU (4)” appears on the TV screen and “DIGIT AL IN1” appears on the display . • On the front panel, turn MUL TI JOG, then press SET . 6 Repeat ste ...

  • JVC RX-F31S - page 24

    22 English 7 Setting the speaker distance The distance from your listening point to the speak ers is one of the impor tant elements to obtain the best possib le sound effect from the Surround/DSP modes. By ref erring to the speaker distance, the receiv er automatically sets the delay time of the sound through each speak er so that sounds through al ...

  • JVC RX-F31S - page 25

    23 English Setting bass sound 7 Setting subwoofer output—SUBWOOFER OUT Y ou can select the type of the signal which can be transmitted through the subwoof er. In other words, you can determine whether or not the bass elements of the front speaker channels are transmitted through the subwoof er regardless of the front speaker siz e setting (either ...

  • JVC RX-F31S - page 26

    24 English Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 11) so that the correct source name will appear when y ou select the digital source . Select one of the follo wing components for each term ...

  • JVC RX-F31S - page 27

    25 English Selecting the component video input mode—DVD VIDEO INPUT/VCR VIDEO INPUT When you use the component video inputs f or connecting the D VD recorder (or D VD player) or VCR, register the type of video input jacks. If you ha ve not selected appropriate video input jacks, y ou cannot view the pla yback picture on the TV or the A V COMPU LI ...

  • JVC RX-F31S - page 28

    26 English SUBWOOFER LEVEL (SUBWFR L VL) Adjust the subwoof er output level. (29) FRONT L LEVEL (FR ONT L L VL) Adjust the left front speaker output le vel. (29) FRONT R LEVEL (FR ONT R L VL) Adjust the right front speaker output le vel. (29) CENTER LEVEL (CENTER L VL) Adjust the center speaker output le vel. (29) SURR. L LEVEL (SURR L L VL) Adjust ...

  • JVC RX-F31S - page 29

    27 English DIGITAL EQ 250Hz TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT ADJUST MENU (1) 5 SUBWOOFER LEVEL : 0 FRONT L LEVEL : 0 FRONT R LEVEL : 0 CENTER LEVEL : 0 SURR. L LEVEL : 0 SURR. R LEVEL : 0 SURR. BACK LEVEL : 0 ∞ :ENTER :TOP MENU ADJUST MENU (2) 5 DIGITAL EQ 63Hz : 0 DIGITAL EQ 250Hz : 0 DIGITAL EQ 1kHz : 0 DIGITAL EQ 4kHz : 0 D ...

  • JVC RX-F31S - page 30

    28 English Ex.: When adjusting subwoofer output le vel. 1 To show “T OP MENU, ” press MENU . Then press 5 or ∞ to select “ADJUST MENU . ” • On the front panel, turn MUL TI JOG. 2 To select “ADJUST MENU , ” press SET . 3 To select the desired submenu, press 5 or ∞ repeatedly . There are three screens from “ADJUST MENU (1)” to ? ...

  • JVC RX-F31S - page 31

    29 English From the remote control: Y ou can also make adjustments the f ollowing wa y from the remote control. Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press TEST TONE to c heck the speakers’ output balance. • On the TV screen, “TEST T ONE” appears. The indicator corresponding to the speaker appears while a test tone comes out o ...

  • JVC RX-F31S - page 32

    30 English Adjusting the equalization patterns —DIGIT AL EQ 63Hz/250Hz/1kHz/4kHz/16kHz Y ou can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers . • Once you ha ve made an adjustment, it is memorized f or each source. Adjustable range: –8 (dB) to +8 (dB) (in 2 ...

  • JVC RX-F31S - page 33

    31 English 7 Making the center tone soft or sharp —CENTER TONE This setting is av ailable when one of the Surround/DSP modes is in use. T o activate Surround/DSP mode , see page 39. • This setting is common to all Surround modes, and is memorized separately f or DSP modes. •Y ou cannot adjust the center tone in the f ollowing cases: – When ...

  • JVC RX-F31S - page 34

    32 English T uner operations When operating the receiver using the remote control, set the mode selector to “AUDIO/TV/ VCR/DBS. ” T uning in to stations manually From the remote control ONL Y : 1 Press FM/AM to select the band. The last received station of the selected band is tuned in. • Each time you press the b utton, the band alter nates ...

  • JVC RX-F31S - page 35

    33 English 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10. 4 Press MEMOR Y again while the selected c hannel number is flashing on the displa y ...

  • JVC RX-F31S - page 36

    34 English Creating realistic sound fields Reproducing theater ambience In a movie theater , many speakers are located on the w alls to reproduce impressive m ulti-channel sound, reaching you from all directions. With these many speak ers, sound localization and sound mov ement can be expressed. Surround/DSP modes built in this receiv er can create ...

  • JVC RX-F31S - page 37

    35 English ■ Dolby Surround Dolby Pro Logic II Dolby Pr o Logic II is a m ulti-channel playbac k format to conv er t 2-channel software into 5-channel (plus subwoof er). The matr ix- based conv ersion method used for Dolby Pro Logic II mak es no limitation for the cutoff frequency of the surround treb le and enables stereo surround sound. • Thi ...

  • JVC RX-F31S - page 38

    36 English DTS 96/24 In recent years , there has been increasing interest in higher sampling rates both f or recording and for reproducing at home. Higher sampling rates allow wider frequency r ange and greater bit depths provide e xtended dynamic range. DTS 96/24 is a multi-channel digital signal f or mat (fs 96 kHz/24 bits) introduced by Digital ...

  • JVC RX-F31S - page 39

    37 English Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are delay ed by the distances of the ceiling and walls. These direct so ...

  • JVC RX-F31S - page 40

    38 English Virtual Surround Back This function creates the great surround eff ect from the behind as if you hav e connected the surround back speaker . The VIR TU AL SB (Surround Back) indicator lights up on the displa y . If you ha ve connected (and activated) the surround speak ers, you can use Vir tual Surround Back without connecting the surrou ...

  • JVC RX-F31S - page 41

    39 English On the front panel: Before y ou star t, remember ... There is a time limit in doing the f ollowing steps . If the setting is canceled before y ou finish, star t from step 2 again. 1 Select and play an y source other than “D VD MUL TI. ” • Make sure y ou have selected the input mode (analog or digital) correctly . 2 Press SURROUND . ...

  • JVC RX-F31S - page 42

    40 English 110V 127V 220V 230 - 240V AV COMPU LINK- III AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , DVD pla yer*, and VCR) through this receiver . This receiver is equipped with the A V COMPU LINK- ...

  • JVC RX-F31S - page 43

    41 English One-touch DVD play Simply by starting playbac k on the D VD play er , you can enjoy the D VD pla yback without setting other s witches manually . • When the D VD pla yer is connected through the analog input jacks on this receiv er (and analog input is selected), the receiver automatically turns on and changes the source to “D VR/D V ...

  • JVC RX-F31S - page 44

    42 English Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Ref er also to the manuals supplied with the other products. Some JVC VCRs can accept two types of the control signals— remote codes “A” and “B. ” – When operating a VCR whose remote control code is set to “A, ” s ...

  • JVC RX-F31S - page 45

    43 English For various pla yback: (one touc h replay): Mov e the playback position bac k 10 seconds before the current position. RETURN: Return to the main menu during menu operation. CANCEL: Cancel the programmed trac k, etc. Only for D VD recorder operations: CHANNEL +/–: Change the channel numbers. D VD/HDD: Select the D VD recorder or HDD dec ...

  • JVC RX-F31S - page 46

    44 English By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Ref er also to the manuals supplied with the other products. •T o operate those components with the remote control, first you need to set the manuf acturers’ codes each for the TV , VCR, and DBS. • After r ...

  • JVC RX-F31S - page 47

    45 English ❏ Changing the transmittable signals for operating a VCR Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes f or VCR” on the right. 4 Release VCR . Now , you can perf or m the f ollowing operation on the ...

  • JVC RX-F31S - page 48

    46 English ❏ Changing the transmittable signals for operating a DBS tuner Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press and hold DBS . 2 Press DBS. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes for DBS tuner” below . 4 Release DBS . Now , you can perf orm the following operation on t ...

  • JVC RX-F31S - page 49

    47 English Tr oubleshooting PROBLEM The pow er does not come on. The receiver turns off (enters standby mode). “O VER HEA T” flashes on the display , then the receiver turns off . No sound from speakers . Sound from one speaker only . Bass sound is reinf orced too much when listening in stereo . Sounds are intermittently distor ted or the noise ...

  • JVC RX-F31S - page 50

    48 English Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 100 W* per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 10% total harmonic distor tion. At surround operation: F ront channels: 100 W* per channel, min. RMS, driven into 6 Ω at 1 kHz with no m ...

  • JVC RX-F31S - page 51

    VIDEO DBS IN VCR VIDEO OUT (REC) IN (PLAY) S-VIDEO DVR OUT (REC) DVR/DVD IN (PLAY) MONITOR OUT CAUTION:SPEAKER IMPEDANCE 6 – 16 ANTENNA AM LOOP AM EXT COAXIAL FM 75 CENTER SURROUND SURROUND BACK SPEAKERS LEFT RIGHT LEFT RIGHT FRONT Y P B P R COMPONENT MONITOR OUT DVR/DVD IN VCR IN PCM/ STREAM SURR-L SURR-R CENTER SUBWOOFER DIGITAL OUT DVD MULTI I ...

  • JVC RX-F31S - page 52

    LVT1306-011B [UJ] RX-F31S INSTR UCTIONS HOME CINEMA CONTR OL CENTER cover_RX-F31S[UJ]ff.p65 05.6.9, 17:59 3 ...

  • JVC RX-F31S - page 53

    G-1 RX-F31S W arnings, Cautions, and Other s Caution–– STANDBY/ON button! Disconnect the mains plug to shut the pow er off completely . The ST ANDBY/ON button in any position does not disconnect the mains line. The po wer can be remote controlled. CA UTION To reduce the risk of electrical shocks, fire , etc.: 1. Do not remov e screws, cov ers o ...

  • JVC RX-F31S - page 54

    1 Ta b le of Contents Pa r ts identification ................................................ 2 Getting started ...................................................... 4 Before Installation .................................................................. 4 Checking the supplied accessories ....................................... 4 Putting batterie ...

  • JVC RX-F31S - page 55

    2 SET HOME CINEMA CONTROL CENTER REMOTE CONTR OL RM - SRXF31U 4 2 t 3 1 5 9 8 7 q w e r u y i o p 6 Remote control See pages in parentheses f or details. 1 TV DIRECT button (14) 2 Source selecting buttons (12, 14, 32, 33) D VR/D VD , VCR, DBS , TV , D VD MUL TI, FM/AM 3 Operating buttons f or tuner (32, 33) ( TUNING, FM MODE, TUNING 9 , MEMORY 4 On ...

  • JVC RX-F31S - page 56

    3 Front panel 1 ST ANDBY/ON button and standby lamp (12, 14, 32) 2 Source lamps D VD MUL TI, D VR/D VD , VCR, DBS , TV , FM/AM 3 • SOURCE SELECT OR (12, 14, 33) • MUL TI JOG (18, 26, 33, 39) 4 MASTER VOLUME control (13) 5 PHONES jack (13) 6 TV DIRECT button (14) 7 SETTING button (18, 32) 8 ADJUST button (26, 32) 9 SURROUND b utton (39) p Remote ...

  • JVC RX-F31S - page 57

    4 Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–). 3 Replace the cover . If the range or eff ectiveness of the remote control decrease ...

  • JVC RX-F31S - page 58

    5 110V 127V 220V 230 - 240V ANTENNA AM LOOP AM EXT COAXIAL FM 75 ANTENNA Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed. AM loop antenna (supplied) If AM reception is poor, connect an outd ...

  • JVC RX-F31S - page 59

    6 LR LS RS SB C SW 110V 127V 220V 230 - 240V CAUTION:SPEAKER IMPEDANCE 6 – 16 CENTER SURROUND SURROUND BACK SPEAKERS LEFT RIGHT LEFT RIGHT FRONT LINK- III OUT SUB- WOOFER AV COMPU Connecting the speakers T urn off all components before making connections. 1 T wist and remove the insulation at the end of eac h speaker cord. 2 Press and hold the cl ...

  • JVC RX-F31S - page 60

    7 This receiver is equipped with the f ollowing video terminals— composite video , S-video, and component video terminals. • If your video components ha ve S-video (Y/C-separation) and/or component video (Y , P B , P R ) jacks , connect them using an S- video cable (not supplied) or component video cab le (not supplied). By using these terminal ...

  • JVC RX-F31S - page 61

    8 110V 127V 220V 230 - 240V VIDEO VCR OUT (REC) Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT DVR/DVD IN (PLAY) DVR OUT (REC) S-VIDEO VCR OUT (REC) DVR OUT (REC) DVR/DVD IN (PLAY) AUDIO SURR-L SURR-R CENTER SUBWOOFER DVD MULTI IN Å ı Ç Î ‰ Ì Ó È Ô Ï 7 Connecting a D VD recorder or D VD player with its analog discrete output jac ks (D ...

  • JVC RX-F31S - page 62

    9 110V 127V 220V 230 - 240V TV VCR DBS IN IN IN (PLAY) DBS IN VCR MONITOR OUT IN (PLAY) Å ı Ç 110V 127V 220V 230 - 240V VCR DBS IN IN (PLAY) OUT (REC) DVR/DVD IN (PLAY) Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT DBS IN VCR OUT (REC) IN (PLAY) DVR/DVD IN (PLAY) ‰ ÏÌ Î Ç Å ı 7 Connecting a VCR Å To left/right audio channel output ? ...

  • JVC RX-F31S - page 63

    10 110V 127V 220V 230 - 240V L R TV DBS IN IN MONITOR OUT OUT SUB- WOOFER DBS IN MONITOR OUT Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT Å ı Ç Î ‰ 7 Connecting a TV Connect the TV to the appropr iate MONIT OR OUT jacks to vie w the pla yback picture from an y other connected video components. Stereo audio cable (not supplied) Red Compon ...

  • JVC RX-F31S - page 64

    11 110V 127V 220V 230 - 240V PCM/ STREAM DIGITAL OUT 110V 127V 220V 230 - 240V DIGITAL IN 3(VCR) 2(DBS) 1(DVR/DVD) NO TES • When shipped from the f actory , the DIGIT AL IN ter minals hav e been set f or use with the f ollowing components: – 1(D VR/D VD): F or D VD recorder or D VD play er – 2(DBS): For DBS tuner – 3(VCR): F or VCR If you c ...

  • JVC RX-F31S - page 65

    12 Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECT OR until the source name y ou want appear s on the display . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECT OR, the source changes as f ollo ws: D VD MUL TI: Select for the D VD player using the analog discrete ...

  • JVC RX-F31S - page 66

    13 3 Adjust the volume To increase the volume, turn MASTER V OLUME control c lockwise (or press V OLUME + on the remote control). To decrease the v olume, turn MASTER V OLUME control counter clockwise (or press V OLUME – on the remote control). • When you adjust the v olume, the volume le vel indication appears on the displa y for a while . CA ...

  • JVC RX-F31S - page 67

    14 Adjusting the subwoofer audio position If the subwoof er sound is much reinforced f or stereo sound compared to the sound reproduced with multi-channel, set the subwoof er audio position. The subwoofer output le vel is automatically decreased by the selected v alue when you are listening in stereo . The A UDIO P . indicator lights up when this f ...

  • JVC RX-F31S - page 68

    15 Tu rning off the sounds temporarily From the remote control ONL Y : Press MUTING to turn off the sound through all connected speakers and headphones. “MUTING” appears on the display and the v olume tur ns off. To restore the sound, press MUTING again. • Pressing VOLUME +/– (or turning MASTER VOLUME control on the front panel) also restor ...

  • JVC RX-F31S - page 69

    16 From the remote control ONL Y : 1 T ake your position where y ou listen to the sound. • Make sure speak er cables are connected fir mly . 2 Press and hold SMART SURR OUND SETUP until “SETTING UP” flashes. *1 L: Left front speaker *2 C: Center speaker *3 R: Right front speaker *4 RS: Right surround speaker *5 SB: Surround back speak er *6 L ...

  • JVC RX-F31S - page 70

    17 When your c lapping sound is detected successfully , • On the TV screen, “SUCCESSFUL, ” “RESUL T , ” and the setting v alues appear . The setting values are shown f or about 12 seconds. Ex.: • On the display , “SUCCESSFUL ” appears, then the setting values are sho wn as follows f or about 12 seconds: Ex.: *7 Standard channel (the ...

  • JVC RX-F31S - page 71

    18 Basic setting items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting. •T he name of the item shown below is the on-screen displa y indication and the name in parentheses is the display indication. * If you ha ve used Smar t Surround Setu ...

  • JVC RX-F31S - page 72

    19 FL SPK DISTANCE TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT SETTING MENU (1) 5 SUBWOOFER : NO FRONT SPK : LARGE CENTER SPK : SMALL SURR. SPK : SMALL SURR. BACK SPK : SMALL ∞ :ENTER :TOP MENU SETTING MENU (2) 5 DISTANCE UNIT :meter FL SPK DISTANCE : 3.0m FR SPK DISTANCE : 3.0m C SPK DISTANCE : 3.0m LS SPK DISTANCE : 3.0m RS SPK DISTANC ...

  • JVC RX-F31S - page 73

    20 DIGITAL IN 1 DIGITAL IN 1: 2 DVR/DVD 3 23 :OPERATE :BACK TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 25). Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the se ...

  • JVC RX-F31S - page 74

    21 4 Press SET . 5 To select the appropriate setting, press 2 or 3 repeatedly , then press SET . The on-screen display returns to the pre vious SETTING MENU . In this example, “SETTING MENU (4)” appears on the TV screen and “DIGIT AL IN1” appears on the display . • On the front panel, turn MUL TI JOG, then press SET . 6 Repeat steps 2 to ...

  • JVC RX-F31S - page 75

    22 7 Setting the speaker distance The distance from your listening point to the speak ers is one of the impor tant elements to obtain the best possib le sound effect from the Surround/DSP modes. By ref erring to the speaker distance, the receiv er automatically sets the delay time of the sound through each speak er so that sounds through all the sp ...

  • JVC RX-F31S - page 76

    23 Setting bass sound 7 Setting subwoofer output—SUBWOOFER OUT Y ou can select the type of the signal which can be transmitted through the subwoof er. In other words, you can determine whether or not the bass elements of the front speaker channels are transmitted through the subwoof er regardless of the front speaker siz e setting (either “SMAL ...

  • JVC RX-F31S - page 77

    24 Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 11) so that the correct source name will appear when y ou select the digital source . Select one of the follo wing components for each terminal: D ...

  • JVC RX-F31S - page 78

    25 Selecting the component video input mode—DVD VIDEO INPUT/VCR VIDEO INPUT When you use the component video inputs f or connecting the D VD recorder (or D VD player) or VCR, register the type of video input jacks . If you ha ve not selected appropriate video input jacks, y ou cannot view the pla yback picture on the TV or the A V COMPU LINK remo ...

  • JVC RX-F31S - page 79

    26 SUBWOOFER LEVEL (SUBWFR L VL) Adjust the subwoof er output level. (29) FRONT L LEVEL (FR ONT L L VL) Adjust the left front speaker output le vel. (29) FRONT R LEVEL (FR ONT R L VL) Adjust the right front speaker output le vel. (29) CENTER LEVEL (CENTER L VL) Adjust the center speaker output le vel. (29) SURR. L LEVEL (SURR L L VL) Adjust the lef ...

  • JVC RX-F31S - page 80

    27 DIGITAL EQ 250Hz TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT ADJUST MENU (1) 5 SUBWOOFER LEVEL : 0 FRONT L LEVEL : 0 FRONT R LEVEL : 0 CENTER LEVEL : 0 SURR. L LEVEL : 0 SURR. R LEVEL : 0 SURR. BACK LEVEL : 0 ∞ :ENTER :TOP MENU ADJUST MENU (2) 5 DIGITAL EQ 63Hz : 0 DIGITAL EQ 250Hz : 0 DIGITAL EQ 1kHz : 0 DIGITAL EQ 4kHz : 0 DIGITAL E ...

  • JVC RX-F31S - page 81

    28 Ex.: When adjusting subwoofer output le vel. 1 To show “T OP MENU, ” press MENU . Then press 5 or ∞ to select “ADJUST MENU . ” • On the front panel, turn MUL TI JOG. 2 To select “ADJUST MENU , ” press SET . 3 To select the desired submenu, press 5 or ∞ repeatedly . There are three screens from “ADJUST MENU (1)” to “ADJUST ...

  • JVC RX-F31S - page 82

    29 From the remote control: Y ou can also make adjustments the f ollowing wa y from the remote control. Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press TEST TONE to c heck the speakers’ output balance. • On the TV screen, “TEST T ONE” appears. The indicator corresponding to the speaker appears while a test tone comes out of the sp ...

  • JVC RX-F31S - page 83

    30 Adjusting the equalization patterns —DIGIT AL EQ 63Hz/250Hz/1kHz/4kHz/16kHz Y ou can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers . • Once you ha ve made an adjustment, it is memorized f or each source. Adjustable range: –8 (dB) to +8 (dB) (in 2 dB inter ...

  • JVC RX-F31S - page 84

    31 7 Making the center tone soft or sharp —CENTER TONE This setting is av ailable when one of the Surround/DSP modes is in use. T o activate Surround/DSP mode , see page 39. • This setting is common to all Surround modes, and is memorized separately f or DSP modes. •Y ou cannot adjust the center tone in the f ollowing cases: – When “CENTE ...

  • JVC RX-F31S - page 85

    32 Setting the AM tuner interval spacing Some countries space AM stations 9 kHz apar t, and other countries use 10 kHz spacing. 9 kHz inter val spacing is the initial setting. • Be sure the receiver is turned off, b ut is plugged into an AC outlet when setting the AM tuner interval. On the front panel ONL Y: To select the 10 kHz interval: Hold do ...

  • JVC RX-F31S - page 86

    33 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10. 4 Press MEMOR Y again while the selected c hannel number is flashing on the displa y . The se ...

  • JVC RX-F31S - page 87

    34 Creating realistic sound fields Reproducing theater ambience In a movie theater , many speakers are located on the w alls to reproduce impressive m ulti-channel sound, reaching you from all directions. With these many speak ers, sound localization and sound mov ement can be expressed. Surround/DSP modes built in this receiv er can create almost ...

  • JVC RX-F31S - page 88

    35 ■ Dolby Surround Dolby Pro Logic II Dolby Pr o Logic II is a m ulti-channel playbac k format to conv er t 2-channel software into 5-channel (plus subwoof er). The matr ix- based conv ersion method used for Dolby Pro Logic II mak es no limitation for the cutoff frequency of the surround treb le and enables stereo surround sound. • This receiv ...

  • JVC RX-F31S - page 89

    36 DTS 96/24 In recent years , there has been increasing interest in higher sampling rates both f or recording and for reproducing at home. Higher sampling rates allow wider frequency r ange and greater bit depths provide e xtended dynamic range. DTS 96/24 is a multi-channel digital signal f or mat (fs 96 kHz/24 bits) introduced by Digital Theater ...

  • JVC RX-F31S - page 90

    37 Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are delay ed by the distances of the ceiling and walls. These direct sounds and ...

  • JVC RX-F31S - page 91

    38 Virtual Surround Back This function creates the great surround eff ect from the behind as if you hav e connected the surround back speaker . The VIR TU AL SB (Surround Back) indicator lights up on the displa y . If you ha ve connected (and activated) the surround speak ers, you can use Vir tual Surround Back without connecting the surround back ...

  • JVC RX-F31S - page 92

    39 On the front panel: Before y ou star t, remember ... There is a time limit in doing the f ollowing steps . If the setting is canceled before y ou finish, star t from step 2 again. 1 Select and play an y source other than “D VD MUL TI. ” • Make sure y ou have selected the input mode (analog or digital) correctly . 2 Press SURROUND . MUL TI ...

  • JVC RX-F31S - page 93

    40 110V 127V 220V 230 - 240V AV COMPU LINK- III AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , DVD pla yer*, and VCR) through this receiver . This receiver is equipped with the A V COMPU LINK- III , w ...

  • JVC RX-F31S - page 94

    41 One-touch DVD play Simply by starting playbac k on the D VD play er , you can enjoy the D VD pla yback without setting other s witches manually . • When the D VD pla yer is connected through the analog input jacks on this receiv er (and analog input is selected), the receiver automatically turns on and changes the source to “D VR/D VD” or ...

  • JVC RX-F31S - page 95

    42 Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Ref er also to the manuals supplied with the other products. Some JVC VCRs can accept two types of the control signals— remote codes “A” and “B. ” – When operating a VCR whose remote control code is set to “A, ” set the m ...

  • JVC RX-F31S - page 96

    43 For various pla yback: (one touc h replay): Mov e the playback position bac k 10 seconds before the current position. RETURN: Return to the main menu during menu operation. CANCEL: Cancel the programmed trac k, etc. Only for D VD recorder operations: CHANNEL +/–: Change the channel numbers. D VD/HDD: Select the D VD recorder or HDD deck. (Only ...

  • JVC RX-F31S - page 97

    44 By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Ref er also to the manuals supplied with the other products. •T o operate those components with the remote control, first you need to set the manuf acturers’ codes each for the TV , VCR, and DBS. • After replacing ...

  • JVC RX-F31S - page 98

    45 ❏ Changing the transmittable signals for operating a VCR Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes f or VCR” on the right. 4 Release VCR . Now , you can perf or m the f ollowing operation on the VCR. VCR ...

  • JVC RX-F31S - page 99

    46 ❏ Changing the transmittable signals for operating a DBS tuner Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press and hold DBS . 2 Press DBS. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes for DBS tuner” below . 4 Release DBS . Now , you can perf orm the following operation on the DBS t ...

  • JVC RX-F31S - page 100

    47 Tr oubleshooting PROBLEM The pow er does not come on. The receiver turns off (enters standby mode). “O VER HEA T” flashes on the display , then the receiver turns off . No sound from speakers . Sound from one speaker only . Bass sound is reinf orced too much when listening in stereo . Sounds are intermittently distor ted or the noise is hear ...

  • JVC RX-F31S - page 101

    48 Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 100 W* per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 10% total harmonic distor tion. At surround operation: F ront channels: 100 W* per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than ...

  • JVC RX-F31S - page 102

    VIDEO DBS IN VCR VIDEO OUT (REC) IN (PLAY) S-VIDEO DVR OUT (REC) DVR/DVD IN (PLAY) MONITOR OUT CAUTION:SPEAKER IMPEDANCE 6 – 16 ANTENNA AM LOOP AM EXT COAXIAL FM 75 CENTER SURROUND SURROUND BACK SPEAKERS LEFT RIGHT LEFT RIGHT FRONT Y P B P R COMPONENT MONITOR OUT DVR/DVD IN VCR IN PCM/ STREAM SURR-L SURR-R CENTER SUBWOOFER DIGITAL OUT DVD MULTI I ...

  • JVC RX-F31S - page 103

    LVT1306-012A [A] RX-F31S INSTR UCTIONS HOME CINEMA CONTROL CENTER cover_RX-F31S[A]2.p65 05.6.13, 10:33 3 ...

  • JVC RX-F31S - page 104

    G-1 RX-F31S W arnings, Cautions, and Other s Caution–– STANDBY/ON button! Disconnect the mains plug to shut the pow er off completely . The ST ANDBY/ON button in any position does not disconnect the mains line. The po wer can be remote controlled. CA UTION To reduce the risk of electrical shocks, fire , etc.: 1. Do not remov e screws, cov ers o ...

  • JVC RX-F31S - page 105

    1 Ta b le of Contents Pa r ts identification ................................................ 2 Getting started ...................................................... 4 Before Installation .................................................................. 4 Checking the supplied accessories ....................................... 4 Putting batterie ...

  • JVC RX-F31S - page 106

    2 SET HOME CINEMA CONTROL CENTER REMOTE CONTR OL RM - SRXF31U 4 2 t 3 1 5 9 8 7 q w e r u y i o p 6 Remote control See pages in parentheses f or details. 1 TV DIRECT button (14) 2 Source selecting buttons (12, 14, 32, 33) D VR/D VD , VCR, DBS , TV , D VD MUL TI, FM/AM 3 Operating buttons f or tuner (32, 33) ( TUNING, FM MODE, TUNING 9 , MEMORY 4 On ...

  • JVC RX-F31S - page 107

    3 Front panel 1 ST ANDBY/ON button and standby lamp (12, 14, 32) 2 Source lamps D VD MUL TI, D VR/D VD , VCR, DBS , TV , FM/AM 3 • SOURCE SELECT OR (12, 14, 33) • MUL TI JOG (18, 26, 33, 39) 4 MASTER VOLUME control (13) 5 PHONES jack (13) 6 TV DIRECT button (14) 7 SETTING button (18, 32) 8 ADJUST button (26, 32) 9 SURROUND b utton (39) p Remote ...

  • JVC RX-F31S - page 108

    4 Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–). 3 Replace the cover . If the range or eff ectiveness of the remote control decrease ...

  • JVC RX-F31S - page 109

    5 110V 127V 220V 230 - 240V ANTENNA AM LOOP AM EXT COAXIAL FM 75 ANTENNA Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed. AM loop antenna (supplied) If AM reception is poor, connect an outd ...

  • JVC RX-F31S - page 110

    6 LR LS RS SB C SW 110V 127V 220V 230 - 240V CAUTION:SPEAKER IMPEDANCE 6 – 16 CENTER SURROUND SURROUND BACK SPEAKERS LEFT RIGHT LEFT RIGHT FRONT LINK- III OUT SUB- WOOFER AV COMPU Connecting the speakers T urn off all components before making connections. 1 T wist and remove the insulation at the end of eac h speaker cord. 2 Press and hold the cl ...

  • JVC RX-F31S - page 111

    7 This receiver is equipped with the f ollowing video terminals— composite video , S-video, and component video terminals. • If your video components ha ve S-video (Y/C-separation) and/or component video (Y , P B , P R ) jacks , connect them using an S- video cable (not supplied) or component video cab le (not supplied). By using these terminal ...

  • JVC RX-F31S - page 112

    8 110V 127V 220V 230 - 240V VIDEO VCR OUT (REC) Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT DVR/DVD IN (PLAY) DVR OUT (REC) S-VIDEO VCR OUT (REC) DVR OUT (REC) DVR/DVD IN (PLAY) AUDIO SURR-L SURR-R CENTER SUBWOOFER DVD MULTI IN Å ı Ç Î ‰ Ì Ó È Ô Ï 7 Connecting a D VD recorder or D VD player with its analog discrete output jac ks (D ...

  • JVC RX-F31S - page 113

    9 110V 127V 220V 230 - 240V TV VCR DBS IN IN IN (PLAY) DBS IN VCR MONITOR OUT IN (PLAY) Å ı Ç 110V 127V 220V 230 - 240V VCR DBS IN IN (PLAY) OUT (REC) DVR/DVD IN (PLAY) Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT DBS IN VCR OUT (REC) IN (PLAY) DVR/DVD IN (PLAY) ‰ ÏÌ Î Ç Å ı 7 Connecting a VCR Å To left/right audio channel output ? ...

  • JVC RX-F31S - page 114

    10 110V 127V 220V 230 - 240V L R TV DBS IN IN MONITOR OUT OUT SUB- WOOFER DBS IN MONITOR OUT Y P B P R MONITOR OUT DVR/DVD IN VCR IN COMPONENT Å ı Ç Î ‰ 7 Connecting a TV Connect the TV to the appropr iate MONIT OR OUT jacks to vie w the pla yback picture from an y other connected video components. Stereo audio cable (not supplied) Red Compon ...

  • JVC RX-F31S - page 115

    11 110V 127V 220V 230 - 240V PCM/ STREAM DIGITAL OUT 110V 127V 220V 230 - 240V DIGITAL IN 3(VCR) 2(DBS) 1(DVR/DVD) NO TES • When shipped from the f actory , the DIGIT AL IN ter minals hav e been set f or use with the f ollowing components: – 1(D VR/D VD): F or D VD recorder or D VD play er – 2(DBS): For DBS tuner – 3(VCR): F or VCR If you c ...

  • JVC RX-F31S - page 116

    12 Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECT OR until the source name y ou want appear s on the display . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECT OR, the source changes as f ollo ws: D VD MUL TI: Select for the D VD player using the analog discrete ...

  • JVC RX-F31S - page 117

    13 3 Adjust the volume To increase the volume, turn MASTER V OLUME control c lockwise (or press V OLUME + on the remote control). To decrease the v olume, turn MASTER V OLUME control counter clockwise (or press V OLUME – on the remote control). • When you adjust the v olume, the volume le vel indication appears on the displa y for a while . CA ...

  • JVC RX-F31S - page 118

    14 Adjusting the subwoofer audio position If the subwoof er sound is much reinforced f or stereo sound compared to the sound reproduced with multi-channel, set the subwoof er audio position. The subwoofer output le vel is automatically decreased by the selected v alue when you are listening in stereo . The A UDIO P . indicator lights up when this f ...

  • JVC RX-F31S - page 119

    15 Tu rning off the sounds temporarily From the remote control ONL Y : Press MUTING to turn off the sound through all connected speakers and headphones. “MUTING” appears on the display and the v olume tur ns off. To restore the sound, press MUTING again. • Pressing VOLUME +/– (or turning MASTER VOLUME control on the front panel) also restor ...

  • JVC RX-F31S - page 120

    16 From the remote control ONL Y : 1 T ake your position where y ou listen to the sound. • Make sure speak er cables are connected fir mly . 2 Press and hold SMART SURR OUND SETUP until “SETTING UP” flashes. *1 L: Left front speaker *2 C: Center speaker *3 R: Right front speaker *4 RS: Right surround speaker *5 SB: Surround back speak er *6 L ...

  • JVC RX-F31S - page 121

    17 When your c lapping sound is detected successfully • On the TV screen, “SUCCESSFUL, ” “RESUL T , ” and the setting v alues appear . The setting values are shown f or about 12 seconds. Ex.: • On the display , “SUCCESSFUL ” appears, then the setting values are sho wn as follows f or about 12 seconds: Ex.: *7 Standard channel (the c ...

  • JVC RX-F31S - page 122

    18 Basic setting items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting. •T he name of the item shown below is the on-screen displa y indication and the name in parentheses is the display indication. * If you ha ve used Smar t Surround Setu ...

  • JVC RX-F31S - page 123

    19 FL SPK DISTANCE TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT SETTING MENU (1) 5 SUBWOOFER : NO FRONT SPK : LARGE CENTER SPK : SMALL SURR. SPK : SMALL SURR. BACK SPK : SMALL ∞ :ENTER :TOP MENU SETTING MENU (2) 5 DISTANCE UNIT :meter FL SPK DISTANCE : 3.0m FR SPK DISTANCE : 3.0m C SPK DISTANCE : 3.0m LS SPK DISTANCE : 3.0m RS SPK DISTANC ...

  • JVC RX-F31S - page 124

    20 DIGITAL IN 1 DIGITAL IN 1: 2 DVR/DVD 3 23 :OPERATE :BACK TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 25). Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the se ...

  • JVC RX-F31S - page 125

    21 4 Press SET . 5 To select the appropriate setting, press 2 or 3 repeatedly , then press SET . The on-screen display returns to the pre vious SETTING MENU . In this example, “SETTING MENU (4)” appears on the TV screen and “DIGIT AL IN1” appears on the display . • On the front panel, turn MUL TI JOG, then press SET . 6 Repeat steps 2 to ...

  • JVC RX-F31S - page 126

    22 7 Setting the speaker distance The distance from your listening point to the speak ers is one of the impor tant elements to obtain the best possib le sound effect from the Surround/DSP modes. By ref erring to the speaker distance, the receiv er automatically sets the delay time of the sound through each speak er so that sounds through all the sp ...

  • JVC RX-F31S - page 127

    23 Setting bass sound 7 Setting subwoofer output—SUBWOOFER OUT Y ou can select the type of the signal which can be transmitted through the subwoof er. In other words, you can determine whether or not the bass elements of the front speaker channels are transmitted through the subwoof er regardless of the front speaker siz e setting (either “SMAL ...

  • JVC RX-F31S - page 128

    24 Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 11) so that the correct source name will appear when y ou select the digital source . Select one of the follo wing components for each terminal: D ...

  • JVC RX-F31S - page 129

    25 Selecting the component video input mode—DVD VIDEO INPUT/VCR VIDEO INPUT When you use the component video inputs f or connecting the D VD recorder (or D VD player) or VCR, register the type of video input jacks . If you ha ve not selected appropriate video input jacks, y ou cannot view the pla yback picture on the TV or the A V COMPU LINK remo ...

  • JVC RX-F31S - page 130

    26 SUBWOOFER LEVEL (SUBWFR L VL) Adjust the subwoof er output level. (29) FRONT L LEVEL (FR ONT L L VL) Adjust the left front speaker output le vel. (29) FRONT R LEVEL (FR ONT R L VL) Adjust the right front speaker output le vel. (29) CENTER LEVEL (CENTER L VL) Adjust the center speaker output le vel. (29) SURR. L LEVEL (SURR L L VL) Adjust the lef ...

  • JVC RX-F31S - page 131

    27 DIGITAL EQ 250Hz TOP MENU 5 SETTING MENU ADJUST MENU ∞ :ENTER :EXIT ADJUST MENU (1) 5 SUBWOOFER LEVEL : 0 FRONT L LEVEL : 0 FRONT R LEVEL : 0 CENTER LEVEL : 0 SURR. L LEVEL : 0 SURR. R LEVEL : 0 SURR. BACK LEVEL : 0 ∞ :ENTER :TOP MENU ADJUST MENU (2) 5 DIGITAL EQ 63Hz : 0 DIGITAL EQ 250Hz : 0 DIGITAL EQ 1kHz : 0 DIGITAL EQ 4kHz : 0 DIGITAL E ...

  • JVC RX-F31S - page 132

    28 Ex.: When adjusting subwoofer output le vel. 1 To show “T OP MENU, ” press MENU . Then press 5 or ∞ to select “ADJUST MENU . ” • On the front panel, turn MUL TI JOG. 2 To select “ADJUST MENU , ” press SET . 3 To select the desired submenu, press 5 or ∞ repeatedly . There are three screens from “ADJUST MENU (1)” to “ADJUST ...

  • JVC RX-F31S - page 133

    29 From the remote control: Y ou can also make adjustments the f ollowing wa y from the remote control. Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press TEST TONE to c heck the speakers’ output balance. • On the TV screen, “TEST T ONE” appears. The indicator corresponding to the speaker appears while a test tone comes out of the sp ...

  • JVC RX-F31S - page 134

    30 Adjusting the equalization patterns —DIGIT AL EQ 63Hz/250Hz/1kHz/4kHz/16kHz Y ou can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers . • Once you ha ve made an adjustment, it is memorized f or each source. Adjustable range: –8 (dB) to +8 (dB) (in 2 dB inter ...

  • JVC RX-F31S - page 135

    31 7 Making the center tone soft or sharp —CENTER TONE This setting is av ailable when one of the Surround/DSP modes is in use. T o activate Surround/DSP mode , see page 39. • This setting is common to all Surround modes, and is memorized separately f or DSP modes. •Y ou cannot adjust the center tone in the f ollowing cases: – When “CENTE ...

  • JVC RX-F31S - page 136

    32 T uner operations When operating the receiver using the remote control, set the mode selector to “AUDIO/TV/ VCR/DBS. ” T uning in to stations manually From the remote control ONL Y : 1 Press FM/AM to select the band. The last received station of the selected band is tuned in. • Each time you press the b utton, the band alter nates between ...

  • JVC RX-F31S - page 137

    33 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10. 4 Press MEMOR Y again while the selected c hannel number is flashing on the displa y . The se ...

  • JVC RX-F31S - page 138

    34 Creating realistic sound fields Reproducing theater ambience In a movie theater , many speakers are located on the w alls to reproduce impressive m ulti-channel sound, reaching you from all directions. With these many speak ers, sound localization and sound mov ement can be expressed. Surround/DSP modes built in this receiv er can create almost ...

  • JVC RX-F31S - page 139

    35 ■ Dolby Surround Dolby Pro Logic II Dolby Pr o Logic II is a m ulti-channel playbac k format to convert 2-channel software into 5-channel (plus subwoof er). The matr ix- based conv ersion method used for Dolby Pro Logic II mak es no limitation for the cutoff frequency of the surround treb le and enables stereo surround sound. • This receiv e ...

  • JVC RX-F31S - page 140

    36 DTS 96/24 In recent years , there has been increasing interest in higher sampling rates both f or recording and for reproducing at home. Higher sampling rates allow wider frequency r ange and greater bit depths provide e xtended dynamic range. DTS 96/24 is a multi-channel digital signal f or mat (fs 96 kHz/24 bits) introduced by Digital Theater ...

  • JVC RX-F31S - page 141

    37 Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are delay ed by the distances of the ceiling and walls. These direct sounds and ...

  • JVC RX-F31S - page 142

    38 Virtual Surround Back This function creates the great surround eff ect from the behind as if you hav e connected the surround back speaker . The VIR TU AL SB (Surround Back) indicator lights up on the displa y . If you ha ve connected (and activated) the surround speak ers, you can use Vir tual Surround Back without connecting the surround back ...

  • JVC RX-F31S - page 143

    39 On the front panel: Before y ou star t, remember ... There is a time limit in doing the f ollowing steps . If the setting is canceled before y ou finish, star t from step 2 again. 1 Select and play an y source other than “D VD MUL TI. ” • Make sure y ou have selected the input mode (analog or digital) correctly . 2 Press SURROUND . MUL TI ...

  • JVC RX-F31S - page 144

    40 110V 127V 220V 230 - 240V AV COMPU LINK- III AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , DVD pla yer*, and VCR) through this receiver . This receiver is equipped with the A V COMPU LINK- III , w ...

  • JVC RX-F31S - page 145

    41 One-touch DVD play Simply by starting playbac k on the D VD play er , you can enjoy the D VD pla yback without setting other s witches manually . • When the D VD pla yer is connected through the analog input jacks on this receiv er (and analog input is selected), the receiver automatically turns on and changes the source to “D VR/D VD” or ...

  • JVC RX-F31S - page 146

    42 Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Ref er also to the manuals supplied with the other products. Some JVC VCRs can accept two types of the control signals— remote codes “A” and “B. ” – When operating a VCR whose remote control code is set to “A, ” set the m ...

  • JVC RX-F31S - page 147

    43 For various pla yback: (one touc h replay): Mov e the playback position bac k 10 seconds before the current position. RETURN: Return to the main menu during menu operation. CANCEL: Cancel the programmed trac k, etc. Only for D VD recorder operations: CHANNEL +/–: Change the channel numbers. D VD/HDD: Select the D VD recorder or HDD deck. (Only ...

  • JVC RX-F31S - page 148

    44 By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Ref er also to the manuals supplied with the other products. •T o operate those components with the remote control, first you need to set the manuf acturers’ codes each for the TV , VCR, and DBS. • After replacing ...

  • JVC RX-F31S - page 149

    45 ❏ Changing the transmittable signals for operating a VCR Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes f or VCR” on the right. 4 Release VCR . Now , you can perf or m the f ollowing operation on the VCR. VCR ...

  • JVC RX-F31S - page 150

    46 ❏ Changing the transmittable signals for operating a DBS tuner Set the mode selector to “AUDIO/TV/VCR/DBS. ” 1 Press and hold DBS . 2 Press DBS. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes for DBS tuner” below . 4 Release DBS . Now , you can perf orm the following operation on the DBS t ...

  • JVC RX-F31S - page 151

    47 Tr oubleshooting PROBLEM The pow er does not come on. The receiver turns off (enters standby mode). “O VER HEA T” flashes on the display , then the receiver turns off . No sound from speakers . Sound from one speaker only . Bass sound is reinf orced too much when listening in stereo . Sounds are intermittently distor ted or the noise is hear ...

  • JVC RX-F31S - page 152

    48 Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 100 W* per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 10% total harmonic distor tion. At surround operation: F ront channels: 100 W* per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than ...

  • JVC RX-F31S - page 153

    VIDEO DBS IN VCR VIDEO OUT (REC) IN (PLAY) S-VIDEO DVR OUT (REC) DVR/DVD IN (PLAY) MONITOR OUT CAUTION:SPEAKER IMPEDANCE 6 – 16 ANTENNA AM LOOP AM EXT COAXIAL FM 75 CENTER SURROUND SURROUND BACK SPEAKERS LEFT RIGHT LEFT RIGHT FRONT Y P B P R COMPONENT MONITOR OUT DVR/DVD IN VCR IN PCM/ STREAM SURR-L SURR-R CENTER SUBWOOFER DIGITAL OUT DVD MULTI I ...

Produzent JVC Kategorie Home Theater System

Dokumente, die wir vom Produzenten des Geräts JVC RX-F31S erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen JVC
- Bedienungsanleitungen RX-F31S
- Produktkarten JVC
- Informationsbroschüren
- oder Energieetiketten JVC RX-F31S
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung JVC RX-F31S.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen JVC RX-F31S, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen JVC RX-F31S. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts JVC RX-F31S ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts JVC RX-F31S, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von JVC RX-F31S hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von JVC RX-F31S verständlich ist.

Eine gänzliche Bedienungsanleitung von JVC sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von JVC RX-F31S bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von JVC RX-F31S befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich JVC RX-F31S, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts JVC RX-F31S - die uns die ersten Schritte während der Nutzung von JVC RX-F31S erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit JVC RX-F31S hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von JVC RX-F31S im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich JVC RX-F31S?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit JVC RX-F31S nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit JVC RX-F31S hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)