Deutsch dropdown-ico

Bedienungsanleitung Craftsman 137.21229

28 Seiten 5.55 mb
Download

Zur Seite of 28

Summary
  • Craftsman 137.21229 - page 1

    Operator's Manuam ® 10 in. COMPOUND MITER SAW Modem No. 137.212290 CAUTmON: Before using this Mker Saw, read this manual and follow all its Safety Rules and Operating Instructions o Safety mnstructions o mnstaliation o Operation o Maintenance o Parts List Customer Help Line 1 o800o843ol 682 Sears, Roebuck and Co., Hoffman Estates, IL 60179 US ...

  • Craftsman 137.21229 - page 2

    ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool fails due to a defect in material or workmanship within one year from the date of purchase, CALL 1-800-4-MY-HOME ® TO ARRANGE FOR FREE REPAIR. If this tool is used for commercial or rental purposes, this warranty will apply for only ninety days from the date of purchase. This warranty ...

  • Craftsman 137.21229 - page 3

    GENERAL SAFETY mNSTRUCTmONS BEFORE USmNG THIS POWER TOOL Safety is a combination of common sense, staying alert and knowing how to use your power tool. l,&WARNING n To avoid mistakes that could cause serious injury, do not plug the too! in unti! you have read and understood the following. 12.ALWAYS WEAR EYE PROTECTION Any power too! can throw f ...

  • Craftsman 137.21229 - page 4

    SPECiFiC SAFETY mNSTRUCTmONS FOR THiS COMPOUND MINTER SAW 1. USE ONLY CROSS-CUTTiNG SAW BLADES. When using carbide tipped blades, make sure they have a negative hook angle. IMPORTANT: DO NOT USE THIN KERF BLADES- they can deflect and contact guard and can cause possible injury to the operator. 2. DO NOT operate the miter saw until it is completely ...

  • Craftsman 137.21229 - page 5

    ELECTRICAL REQUREMENTS - cont'd DOUBLE iNSULATED The power tool is double insulated to provide a double thickness of insulation between you and tool's electrical system. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Replacement parts = When servicing use only identical replacemen ...

  • Craftsman 137.21229 - page 6

    RECOMMENDED ACCESSORIES IA WARNING I Use only accessories recommended for this miter saw. Foltow instructions that accompany accessories. Use of improper accessories may cause hazards. , The usa of any cutting too! except 10 inch saw blades which meet the requirements under recommended accessories is prohibited. Do not use accessories such as shape ...

  • Craftsman 137.21229 - page 7

    UNPACKING YOUR MINTER SAW IA WARNING n To avoid injury from unexpected starting or electrical shock, do not plug the power cord into a source of power during unpacking and assembly. This cord must remain unplugged whenever you are working on the saw. 1. Remove the miter saw from the carton. iMPORTANT: Do not lift miter saw by the Trigger Switch han ...

  • Craftsman 137.21229 - page 8

    Upper Blade Guard Cover Plate Dust Bag Laser Guide Bevel Scale Hold-Down Clamp Cutting Head Handle ON/OFF Trigger Switch Motor Blade Lower Blade Guard Miter Scale Positive Stop Locking Lever Miter Handle Base Arbor Lock Fence Stop Latch Pivot Bolt Lock-Nut Table Insert / Positive Miter Detents Hand Hold Mounting Hole ...

  • Craftsman 137.21229 - page 9

    COMPOUND MINTER SAW TERMS ARBOR LOCK = Allows the user to keep the blade from rotating while tightening or loosening the arbor bolt during blade replacement or removal BASE = Supports the table, holds accessories and allows for workbench or leg set mounting. BEVEL LOCKING HANDLE = Locks the miter saw at a desired bevel angle. WARNING LABELS = Read ...

  • Craftsman 137.21229 - page 10

    INSTALLING THE MITER HANDLE (FIG. B) 1. Thread the miter handle (1) into the hole (2) located at the front of themiter table. Fig.B Fig. D SAW BLADE WRENCH (FIG. C) 1. For convenient storage andprevention of loss, there is a slot (1) in the rear of the cutting head handle (2) for storing the blade wrench (3) when not in use. Fig. C CUTTING HEAD (FI ...

  • Craftsman 137.21229 - page 11

    REMOVING ORINSTALLING THE BLADE IA WARNING n Only use a 104rich diameter blade. To avoid injury from an accidental start, make sure the switch is in the OFF position and plug is not connected to the power source outlet. 8. Remove the arbor bolt (4), outer blade collar (6), and the blade (7). Do not remove the inner blade collar. (Fig. G=2) NOTE: Pa ...

  • Craftsman 137.21229 - page 12

    2 1 iNSTALLiNG THEHOLD-DOWN CLAMP ASSEMBLY Fig.t (FIG. H) 1_ Place the hold=down clamp assembly (1) in one of the mounting holes (2)_ IA WARN,NG n When using stop block on the right side, hold-down clamp must also be in right side. Using hold-down clamp on the left side during this operation can cause kickback and serious injury to the operator. Fi ...

  • Craftsman 137.21229 - page 13

    Cutting head downward travel adjustment (FIG. L) IA WARNING I To avoid injury from unexpected starting or electrical shock, turn the switch OFF and remove the power cord from the power source. NOTE: Before each cutting operation, check the position of the blade to make sure it does not contact any metal surface. If the blade contacts any metal surf ...

  • Craftsman 137.21229 - page 14

    ALiGNiNG THE LASER BEAM [A WARNING [ For your own safety, never connect the plug to power source outlet unti[ all the adjustment steps are complete and you have read and understood the safety and operational instructions. (1)_ Start with the set screw on the left side of the laser assembly, then with the front set screw on the right side of the las ...

  • Craftsman 137.21229 - page 15

    MOUNTING THE MITER SAW (FIG, O) To avoid injury from unexpected mew movement: , Before moving the saw, disconnect the power cord from the outlet, and !ock the cutting arm in the lower position using the stop latch. NOTE: The stop latch is for carrying or storing the tooL It is not to be used for holding the saw while cutting. Lower blade and press ...

  • Craftsman 137.21229 - page 16

    SAFETY mNSTRUCTmONS FOR BASmC SAW OPERATmON BEFORE USING THE MITER SAW IA WARNING n To avoid mistakes that could cause serious, permanent injury, do not plug the tool in until the following steps are completed: , Completely assemble and adjust the sew, following the instructions. (ASSEMBLY AND ADJUSTMENTS) , Learn the use and function of the ON/OFF ...

  • Craftsman 137.21229 - page 17

    PLAN YOUR WORK Use the right tool. Don'tforce a tool or attachment to do e job it was not designed to do. Use a different tool for any workpiece that can't be held in e solidly braced, fixed position. CAUTION: This machine is not designed for cutting masonry, masonry products, ferrous metals (stee!, iron, and ironobesed metals°) Use this ...

  • Craftsman 137.21229 - page 18

    BODY AND BAND POSITION (FIG. P} Never place hands near the cutting area. Proper positioning of your body andhands when operating the miter sawwillmake cutting easier andsafer. Place hand at least 6=3/4 in. away from the path of the blade, out of the "No=Bands Zone." Bold workpiece firmly against the fence to prevent movement toward the bl ...

  • Craftsman 137.21229 - page 19

    BEVEL CUT (FIG, S) 1_ When a bevel cut is required, loosen the bevel Iock handle (1)_ 2_ Tiltthe cutting head to the desired angle as shown on the bevel scale (2).The blade canbe positioned at any angle, from a 90 ° straight cut(0 ° on the scale) to a 45 ° left bevel. & Tighten the bevel lock handle (1) to lockthe cutting head in position_ F ...

  • Craftsman 137.21229 - page 20

    WORKPtECE SUPPORT (FIG. V) Long pieces need extra support. The support should be placed under the workplece. Keep your hand holding the workpiece positioned 6-3/4 inches or more away from the blade. The support must let the workp+ece layflat on the work table during the cutting operation. NOTE: When mounted on a flatsurface, the miter saw table is ...

  • Craftsman 137.21229 - page 21

    CUTTING A BIJ"_ENSIONAL 4X4 WITH ONE CUT (Fig. X) A dimensional 4x4 workpiece (3ol/2 in_ x 3ol/2 in_ ) may be cut in half with one cut by attaching an auxiliary wood fence of 3/4 inch thick. See "AUXILIARY WOOD FENCE" above. Fig. X Auxiliary Fence _ 3-1/2 in. Miter Saw Fenc / ' _ __._ti L I Miter Saw Table Fig. Z FI Miter Saw ...

  • Craftsman 137.21229 - page 22

    CUTTING CROWN MOLDING (FIG. AA,BB) NOTE: The chart below references s compound cut for crown motding ONLY WHEN THE ANGLE BETWEEN THE WALLS EQUALS EXACTLY 90 ° . Your compound miter saw is suited for the difficult task of cutting crown molding. To fit properly, crown molding must be compound=mitered with extreme accuracy. The two surfaces on a piec ...

  • Craftsman 137.21229 - page 23

    MAINTENANCE I A DA"GER n Never put lubricants on the blade while it is spinning. IA WARNING n To avoid fire or toxic reaction, never use gasoline, naphtha acetone, lacquer thinner or similar highly vo!stile solvents to clean the miter saw. IA WARNmNG H To avoid injury from unexpected starting or electrical shock, unplug the power cord before w ...

  • Craftsman 137.21229 - page 24

    I A WARNING n To avoidinjury from accidental starting, always turn switch OFF and unplug the tool before moving,replacing the blade or making adjustments_ Consult your Sears Service Centre if for any reason the motor wi!! not run. TROUBLESHOOTING GUIDE o MOTOR PROBLEM Brake does not stop blade within 6 seconds. Motor does not start PROBLEM CAUSE 1. ...

  • Craftsman 137.21229 - page 25

    10 in. COMPOUND MITER SAW MODEL NO. 137.212290 IA WAR"I"G n When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Miter Saw may create a HAZARD unless repair is done by a qualified service technician. Repair servic ...

  • Craftsman 137.21229 - page 26

    10 in. COMPOUND MINTER SAW MODEL NO. 137.212290 SCHEMATIC FOR SAW OKA9 2COF 2CIA 083S OKTZ .2D8M OKTX. OKB[ OLS9 0CV5 C_/_ 0_UK ODfB 0KQ_ 3CES 0KSC _'2CU6 _ 2C8D OJMM ssx% 2CSB ...

  • Craftsman 137.21229 - page 27

    10 in. COMPOUND B/liTER SAW MODEL NO. 137.212290 PARTS LIST AND SCHEB_IATtC FOR MOTOR i.D. NO DescfipJion 0HVY BALL BEARING 0HX9 NEEDLE BEARING 0JX3 HEX. SOC. SET SCREW 0KCN CR.RE. PAN HEAD TAPPING & WASHER SCREW 0QQS BRUSH HOLDER ASS'Y 0QQT BRUSH ASS'Y 0QR0 BRUSH COVER 2AKT ARMATURE ASS'Y 2BPA FIELD ASS'Y 2BPB CUTTER SHAFT ...

  • Craftsman 137.21229 - page 28

    Your Home For repair - in your home - of all major brand appfiances, lawn and garden equipment, or heating and coofing systems, no matter who made it, no matter who soJd it! For the replacement parts, accessories and Operator's Manuals that you need to do-it-yourself. For Sears professional installation of home appfiances and items like garage ...

Produzent Craftsman Kategorie Saw

Dokumente, die wir vom Produzenten des Geräts Craftsman 137.21229 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Craftsman
- Bedienungsanleitungen 137.21229
- Produktkarten Craftsman
- Informationsbroschüren
- oder Energieetiketten Craftsman 137.21229
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Craftsman 137.21229.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Craftsman 137.21229, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Craftsman 137.21229. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Craftsman 137.21229 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Craftsman 137.21229, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Craftsman 137.21229 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Craftsman 137.21229 verständlich ist.

Eine gänzliche Bedienungsanleitung von Craftsman sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Craftsman 137.21229 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Craftsman 137.21229 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Craftsman 137.21229, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Craftsman 137.21229 - die uns die ersten Schritte während der Nutzung von Craftsman 137.21229 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Craftsman 137.21229 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Craftsman 137.21229 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Craftsman 137.21229?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Craftsman 137.21229 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Craftsman 137.21229 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)