Bedienungsanleitung Pelco WD57

20 Seiten 0.62 mb
Download

Zur Seite of 20

Summary
  • Pelco WD57 - page 1

    BK57 Blower , HK57 Heater , O/I-PCB and WD57 Defr oster Kits for EH5700/EH5700L Series Envir onmental Enclosur es Installation/ Operation Manual C1423M-D (10/03) 00972 ® Pelco • 3500 Pelco W ay • Clovis, CA 93612-5699 USA • www .pelco.com In North America and Canada: T el (800) 289-9100 • F AX (800) 289-9150 International Customers: T el + ...

  • Pelco WD57 - page 2

    2 Pelco Manual C1423M-D (10/03) REVISION HISTOR Y Manual # Date Comments C1423M 6/95 Original manual. C1423M-A 4/96 Rev . A. Incorporated Manual C1424M for blower kits. Incorporated Manual C1425M for defroster kits. Added instructions for installation of O/I-PCB circuit board kit. Added Operation and Care and Maintenance sections. 5/98 Removed refe ...

  • Pelco WD57 - page 3

    Pelco Manual C1423M-D (10/03) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified ...

  • Pelco WD57 - page 4

    4 Pelco Manual C1423M-D (10/03) 2.0 DESCRIPTION The information in this manual covers the installation and operation of the following kits for the EH5700/EHS700L Series environmental enclosures: BK57-1 Blower kit, 120 VAC, 15 watts BK57-2 Blower kit, 24 VAC, 10 watts BK57-3 Blower kit, 230 VAC, 15 watts HK57-1 Heater kit, 120 VAC, 100 watts HK57-2 ...

  • Pelco WD57 - page 5

    Pelco Manual C1423M-D (10/03) 5 3.0 BLOWER KIT INST ALLA TION This section provides instructions for installing the BK57-1. BK57-2. and BK57-3 blower kits. For the following instructions, refer to Figure 1. T able B lists the parts shown in Figure 1. 1. T urn off power to the enclosure. 2. Unlatch and raise the enclosure lid. The gas spring will ho ...

  • Pelco WD57 - page 6

    6 Pelco Manual C1423M-D (10/03) W ire Gauge Maximum distance from transformer to load T able A. 24 V AC Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.) T otal vA cons ...

  • Pelco WD57 - page 7

    Pelco Manual C1423M-D (10/03) 7 11 . Thermostatically Controlled Operation Only (O/I-PCB Installed) - If the circuit board for thermostatic control of the fan already is installed, complete the installation as follows: a. Remove the plastic power supply barrier cover from the circuit board. b. Connect the plug from the fan into the F AN socket on t ...

  • Pelco WD57 - page 8

    8 Pelco Manual C1423M-D (10/03) T able B. Exploded Assembly Parts List for Blower Item Qty Description Part Number 11 V ent Grill, Beige 57004105COMP 1V ent Grill, Gray 57004005COMP 22 Foam Filter EH550010045 31 24 VDC Fan Rectifier (for -2 model only) PCB9000277ASSY 4-7 Not Used 81 Fan Wire Cord with Plug (-1, -3 models only) WIR432000 91 Fan T ub ...

  • Pelco WD57 - page 9

    Pelco Manual C1423M-D (10/03) 9 4.0 HEA TER KIT INST ALLA TION This section provides instructions for installing the HK57-1, HK57-2, and HK57-3 heater kits. For the following instructions, refer to Figure 2. T able C lists the pans shown in Figure 2. 1. T urn off power to the enclosure. 2. Unlatch and raise the enclosure lid. The gas spring will ho ...

  • Pelco WD57 - page 10

    10 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 11 Bracket/Heat sink 57004020COMP 22 Heater , 230 V AC HTR40220 2 Heater , 24 V AC HTR20024 2 Heater , 120 V AC HTR50120 31 Connector CON1-480424-0 A2 Spacer , .500" Length SP A8423 B4 Internal T ooth Lock W asher , #4 ZH4L WSIS C4 Screw 4-40 x 1/4", Pan Head, Phillips ZH4- ...

  • Pelco WD57 - page 11

    Pelco Manual C1423M-D (10/03) 11 5.0 DEFROSTER KIT INST ALLA TION This section provides instructions for installing the WD57-1, WD57-2, and WD57-3 defroster kits. For the following instructions, refer to Figure 3. T able D lists the parts shown in Figure 3. 1. T urn off power to the enclosure. 2. Unlatch and raise the enclosure lid. The gas spring ...

  • Pelco WD57 - page 12

    12 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 11 Window Defroster , 120 V AC 570010003 1W indow Defroster , 24 V AC 570010006 1W indow Defroster , 230 V AC 570010005 21 Connector Plug CON1-480318-0 T able D. Exploded Assembly Parts List for Defroster Figure 3. Exploded Assembly Diagram for Defroster TO CIRCUIT BOARD 1 2 00969 ...

  • Pelco WD57 - page 13

    Pelco Manual C1423M-D (10/03) 13 6.0 CIRCUIT BOARD KIT INST ALLA TION This section provides instructions for installing the O/I-PCB circuit board kit. For the following instructions, refer to Figure 4. T able E lists the parts shown in Figure 4. 1. Install the circuit board kit (O/I-PCB): a. Remove the mounting bracket from the circuit board. It is ...

  • Pelco WD57 - page 14

    14 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 1 Not Used 2 Not Used 3 Not Used 41 Power Supply Barrier Cover EH470010019 52 Power Supply Barrier EH47004029COMP 61 Circuit Board PCB9000276ASSY 71 Circuit Board Insulator EH450010256 A Not Used B2 Internal T ooth Lock W asher , #4 ZH4L WSIS C2 Screw 4-40 x 1/4", Pan Head. Phil ...

  • Pelco WD57 - page 15

    Pelco Manual C1423M-D (10/03) 15 8. Refer to Figure 5 and connect the camera’s power input to the circuit board. When the power requirements are the same, there are two ways to connect power: (1) A three-pin plug is supplied as loose equipment. Connect the wires from the plug to the camera as follows: Brown - AC HI Blue - AC NT Green - Ground Con ...

  • Pelco WD57 - page 16

    16 Pelco Manual C1423M-D (10/03) Figure 5. Input Wiring Diagram 00967 ...

  • Pelco WD57 - page 17

    Pelco Manual C1423M-D (10/03) 17 7.0 OPERA TION If your enclosure has a thermostatically controlled blower , the thermostat is set to turn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and to turn the fan off be- tween 62 ° and 78 ° F (17 ° and 26 ° C) If your enclosure has thermostatically controlled heaters or defroster , the therm ...

  • Pelco WD57 - page 18

    18 Pelco Manual C1423M-D (10/03) Figure 6. Wiring Diagram for Optional Circuit Board (O/I-PCB) 00970 ...

  • Pelco WD57 - page 19

    Pelco Manual C1423M-D (10/03) 19 Figure 7. Circuit Board Component Locations Figure 8. Circuit Board Layout of T races 00971 ...

  • Pelco WD57 - page 20

    20 Pelco Manual C1423M-D (10/03) 9.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defect ...

Produzent Pelco Kategorie Security Camera

Dokumente, die wir vom Produzenten des Geräts Pelco WD57 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pelco
- Bedienungsanleitungen WD57
- Produktkarten Pelco
- Informationsbroschüren
- oder Energieetiketten Pelco WD57
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pelco WD57.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pelco WD57, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pelco WD57. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pelco WD57 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pelco WD57, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pelco WD57 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pelco WD57 verständlich ist.

Eine gänzliche Bedienungsanleitung von Pelco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pelco WD57 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pelco WD57 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pelco WD57, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pelco WD57 - die uns die ersten Schritte während der Nutzung von Pelco WD57 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pelco WD57 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pelco WD57 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pelco WD57?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco WD57 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco WD57 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)