Deutsch dropdown-ico

Bedienungsanleitung Toshiba IK-TF7

36 Seiten 0.23 mb
Download

Zur Seite of 36

Summary
  • Toshiba IK-TF7 - page 1

    For Customer Use Enter below the Serial No. which is located on the bottom of the cabinet. Retain this information for future ref- erence. Model No.: IK-TF7 Serial No.: 3 CCD CAMERA IK-TF7 INSTRUCTION MANUAL INFORMA TION This equipment has been tested and found to comply with the limits for a Class A digital device, pursu- ant to Part 15 of the FCC ...

  • Toshiba IK-TF7 - page 2

    2 SAFETY PRECAUTIONS Read the following safety precautions carefully before using this product. These instructions contain valuable information on safe and proper use that will prevent harm and damage to the operator and other persons. Make sure that you fully understand the following details (indications, graphic sym- bols) before proceeding to th ...

  • Toshiba IK-TF7 - page 3

    3 Caution • Note the following instructions when installing. • Do not put an inflammable material on the product. • Do not put the product on an Inflammable material such as carpet or blanket. • Do not block a vent hole. • Do not put the product in a narrow space, since the heat generated from the product may be difficult to emanate. If y ...

  • Toshiba IK-TF7 - page 4

    4 1. CA UTIONS ON USE AND INST ALLA TION ..... 5 2. COMPONENTS ................................................ 5 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y .................................... 6 4. NAMES AND FUNCTIONS .............................. 7 5. CONNECTION .................................................. 8 5. 1 Standard Connection . ...

  • Toshiba IK-TF7 - page 5

    5 1. CA UTIONS ON USE AND INST ALLA TION • Carefully handle the units. Do not drop, or give a strong shock or vibration to the camera. This may cause problems. T reat the camera cables carefully to prevent cable problems, such as cable breakdown and loosened connec- tions. • Do not shoot intense light. If there is an intense light at a location ...

  • Toshiba IK-TF7 - page 6

    6 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y MODE E. TRG MANU speed Syncro. scan. Partial scanning T rigger (1P SNR/SR) Trigger (PW SNR/SR) 1P exposure time MODE MANU MODE Color temperature MANUAL R GAIN MANUAL B GAIN Master pedestal R pedestal B pedestal White clip Shading correction mode Manual shading correction H phase adjustment RGB SYNC ...

  • Toshiba IK-TF7 - page 7

    7 4. NAMES AND FUNCTIONS 1 Prism faceplate The protection cap is attached on the lens mount portion. After removing the cap, mount the lens. Be careful not to scratch or touch the optical area. 2 DISP button Used when switching the display . 3 P AGE button Used when switching to the menu and when selecting the menus. 4 MENU UP button Select the fun ...

  • Toshiba IK-TF7 - page 8

    8 5. CONNECTION 5. 1 Standard Connection 5. 2 Cautions on Connection • When connecting the camera cables, be sure to turn off the camera and the other equipment connected. • We suggest using a C mount lens made for a 3CCD camera. When using another lens, the best camera performance of this camera may not be obtained. (For example, low resolutio ...

  • Toshiba IK-TF7 - page 9

    9 6. OPERA TION 1 Referring to the item " 5. CONNECTION", connect each equipment correctly . 2 T urn on the connected equipment and the camera. 3 Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc.. 4 Referring to the item "6.1 White Balance", operate the adjustment. 5 Referring to the items ...

  • Toshiba IK-TF7 - page 10

    10 2 MANU (Manual white balance) • Set the MODE to MANU on the WHT BAL menu. (Refer to the item "7.2 (3) WHT BAL (white balance)".) • Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor or a waveform monitor . (Refer to the item "7.2 (3) (3.2) Chang ...

  • Toshiba IK-TF7 - page 11

    11 7. MODE SETTING BY ON SCREEN DISPLA Y V arious settings can be controlled on the unit by using the on screen menu displayed on the monitor . The contents once set are memorized when the power is turned off, so it is unnecessary to set again when using the unit next time. When the setting is performed, select the menu of the item to be set. 7. 1 ...

  • Toshiba IK-TF7 - page 12

    12 7. 2 Menus • Select the menu to change the setting by referring the item "7.1 Using the Menues".) • When the [MENU UP], [MENU DOWN] buttons are pushed, the " → " on the screen moves up and down. Move the " → " to the item to change. Note: When performing the mode setting in the menu displa y while selecting ...

  • Toshiba IK-TF7 - page 13

    13 (1. 2) Changing each setting in SS (synchro. scan) mode (a) Changing the shutter speed setting 1 Set the " → " to SS by pushing [MENU UP], [MENU DOWN] buttons. 2 Select the shutter speed by pushing [DA T A UP], [DA T A DOWN] buttons. (b) Partial scanning setting 1 Set the " → " to P ART by pushing [MENU UP], [MENU DOWN] b ...

  • Toshiba IK-TF7 - page 14

    14 (1. 3) Changing each setting in E.TRG mode The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR. First set the " → " to MODE and select E. TRG, then set the " → " to E.TRG and select the desired E.TRG mode. (1. 3. 1) Changing each setting in 1P SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 ...

  • Toshiba IK-TF7 - page 15

    15 (1. 3. 2) Changing each setting in 1P SR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either , by pushing [DA T A UP], [DA T A DOWN] buttons. (b) Changing 1P SR exposure time setting 1 Set the " → " to EXP . by pushing [MENU ...

  • Toshiba IK-TF7 - page 16

    16 (1. 3. 3) Changing each setting in PW SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either , by pushing [DA T A UP], [DA T A DOWN] buttons. (b) Changing the partial scanning setting 1 Set the " → " to P ART by pushing [MEN ...

  • Toshiba IK-TF7 - page 17

    17 (1. 3. 4) Changing each setting in PW SR mode -- SHUTTER -- MODE E.TRG E.TRG PW SR TRG.P PART OFF <MODE = E.TRG E.TRG = PW SR> • Partial scanning switch OFF/60fps/90fps Input trigger pulse : positive polarity Input trigger pulse : negative polarity 1P SNR, 1P SR, PW SNR, PW SR, RR • Input trigger pulse setting at PW SNR and PW SR • S ...

  • Toshiba IK-TF7 - page 18

    18 (1. 3. 5) Changing each setting in RR mode (a) Changing the partial scanning setting 1 Set the " → " to P ART by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either OFF or 60fps, 90fps by pushing [DA T A UP], [DA T A DOWN] buttons. Note: The longer the storage time with extended exposures, the more visible certain characteristics ...

  • Toshiba IK-TF7 - page 19

    19 ( 3 ) WHT BAL (White balance) WHT BAL has two modes; AWB, MANU. Set the " → " to MODE, push the [DA TA UP], [DA T A DOWN], and select mode among A WB, MANU. (3. 1) Changing each setting in A WB (Automatic White Balance) mode (a) Changing color temperature setting 1 Set the " → " to C.TEMP by pushing [MENU UP], [MENU DOWN] ...

  • Toshiba IK-TF7 - page 20

    20 ( 4 ) PROCESS (4. 1) Changing master pedestal 1 Set the " → " to M. PED by pushing [MENU UP], [MENU DOWN] buttons. 2 Set the master pedestal by pushing [DA TA UP], [DA T A DOWN] buttons. (4. 2) Changing R pedestal 1 Set the " → " to R. PED by pushing [MENU UP], [MENU DOWN] buttons. 2 Set the R pedestal by pushing [DA T A ...

  • Toshiba IK-TF7 - page 21

    21 ( 5 ) SYNC When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync) automatically . (5. 1) Adjusting horizontal phase 1 Set the " → " to H PHASE by pushing [MENU UP], [MENU DOWN] buttons. 2 Adjust the horizontal phase by pushing [DA T A UP], [DA T A DOWN] buttons. (5. 2) Changing ...

  • Toshiba IK-TF7 - page 22

    22 7. 3 External Sync When using the unit with an external sync signal, input HD and VD to RGB terminal on the rear panel. When the external sync signal is input, the camera automatically switches its sync from the internal sync to the external sync. The operation is as shown below , depending on the unit's status and how external sync signals ...

  • Toshiba IK-TF7 - page 23

    23 ( 3 ) Using the unit with external sync signal When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horizontal phase". (3. 1) H (horizontal) phase adjustment Observe the external sync signal and the video signal output waveform of the unit with a dual trace oscilloscope, and ad- just H phase so that the H phas ...

  • Toshiba IK-TF7 - page 24

    24 7. 5 EXT TRIG (External trigger) Charge begins to accumulate after the trigger input, and 1 frame images are output. There are five modes: 1P SNR, 1P SR, PW SNR, PW SR, RR. The RGB terminal trigger input and index output interface are as shown below . 5V 15k Ω 1SS357 150 Ω Trigger input (CMOS out) INDEX out ( 1 ) 1P SNR (1 Pulse T rig g er S ...

  • Toshiba IK-TF7 - page 25

    25 About 1 µ s Exposure period* 2 Exposure period* 2 Video output 796H (Partial scanning OFF) 387H (Partial scanning 60fps) 258H (Partial scanning 90fps) VIDEO INDEX VD OUT* 3 T rigger* 1 Negative polarity mode Positive polarity mode (1. 2) 1 Pulse T rigger SYNC-NON RESET Picture Output Timing (at Time of Internal Sync) *1: Externally input signal ...

  • Toshiba IK-TF7 - page 26

    26 ( 2 ) 1P SR (1 Pulse T rig g er Sync Reset) Charge begins to accumulate after the trigger input to the RGB terminal, the vertical sync signal is reset and frame images are output. (2. 1) 1 Pulse T rigger SYNC-RESET Picture Output Timing *1: Externally input signal *2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each s ...

  • Toshiba IK-TF7 - page 27

    27 ( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET) The trgger input to the RGB terminal develops 1 frame images. (3. 1) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (At Time of One-shot or Continuous External VD/Continuous External HD Input) *1: Externally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid trigger ...

  • Toshiba IK-TF7 - page 28

    28 (3. 2) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (at Time of Internal Sync) *1: Externally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid trigger pulse width is 2 µ s or greater for external trigger shutter operation.) *3: As long as there is no external sync input, the internal VD will be output when SJ0 ...

  • Toshiba IK-TF7 - page 29

    29 ( 4 ) PW SR (Pulse width trigger SYNC-RESET) The trgger input to the RGB terminal develops 1 frame images. (4. 1) 1 Pulse Width T rigger SYNC-RESET Picture Output Timing *1: Externally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid trigger pulse width is 2 µ s or greater for external trigger shutter operation.) *3: VD is ...

  • Toshiba IK-TF7 - page 30

    30 ( 5 ) RR (Reset restart) Input of an external reset-restart signal (VD terminal) permits one screen of information to be output at an arbitrary timing. (5. 1) Long T erm Exposure When the camera is used and sufficient sensitivity cannot be obtained for the reset-restart function under normal operating conditions, or when observation of the trail ...

  • Toshiba IK-TF7 - page 31

    31 7. 6 Partial Scanning Frame image 1/29.2s (796H) Frame image Frame image 9H Blanking interval B VD Blanking interval D T otal A Video interval C Video output Video period C 1/60s (387H):when 60fps is selected 1/90s (258H):when 90fps is selected   ( 1 ) Partial Scanning OFF (All pixels scanning) In this mode, all pixels independent signal f ...

  • Toshiba IK-TF7 - page 32

    32 8. INPUT OUTPUT SIGNAL SPECIFICA T OINS 4.5V HD VD 0V 4.5V 0V ( 1 ) HD/VD Output Amplitude Specifications ( 4 ) HD Input Specifications The amplitude level is the representative value when terminated with 10k Ω . Output is enabled when the internal switch SJ01 is set to the OUT side. ( 2 ) VD Input Specifications * Input impedance: 75W or 1k ? ...

  • Toshiba IK-TF7 - page 33

    33 9. CCD OUTPUT W A VEFORM TIMING CHART ( 1 ) Horizontal Output Wa veform Timing Char t ( 2 ) V er tical Output Wa veform Timing Char t 102 clk 40 clk 22 clk HSYNC 73 clk CLK=33.9 nsec 151 clk 164 clk 29 clk 3 clk 5 clk 33.9 ns HD CCD output signal 5 clk Optical black portion Video output signal (Representative values) T otal effective pixels 1034 ...

  • Toshiba IK-TF7 - page 34

    34 10. SPECIFICA TIONS Power supply Power consumption Pick-up system Image sensor (Effective pixels) Scanning system Scan frequency Sync system Horizontal resolution Sensitivity Minimum illumination Lens mount Ambient temperature Ambient humidity Weight External dimension White balance Gain Output signal External sync input Sync signal output Inter ...

  • Toshiba IK-TF7 - page 35

    35 12. BEFORE MAKING A SER VICE CALL Symptom No image Poor color Items to be checked • Is the power supplied correctly? • Is the lens iris adjusted correctly? • Are the cables connected correctly? • Is the shutter mode set correctly? • Is the image process equipment set correctly? • Is the monitor (TV) adjusted correctly? • Is the whi ...

  • Toshiba IK-TF7 - page 36

    LIMITED W ARRANTY T OSHIBA CCD CAMERA Promptl y register your product with T oshiba on-line at www.toshiba.com/taisisd. By registering your prod- uct you will be eligible for periodic updates, announcements, and special offers. Y ou will have access to extended warranty options, upgrades (as applicable), useful tips, on-line troubleshooting, and th ...

Produzent Toshiba Kategorie Camcorder

Dokumente, die wir vom Produzenten des Geräts Toshiba IK-TF7 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Toshiba
- Bedienungsanleitungen IK-TF7
- Produktkarten Toshiba
- Informationsbroschüren
- oder Energieetiketten Toshiba IK-TF7
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Toshiba IK-TF7.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Toshiba IK-TF7, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Toshiba IK-TF7. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Toshiba IK-TF7 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Toshiba IK-TF7, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Toshiba IK-TF7 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Toshiba IK-TF7 verständlich ist.

Eine gänzliche Bedienungsanleitung von Toshiba sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Toshiba IK-TF7 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Toshiba IK-TF7 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Toshiba IK-TF7, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Toshiba IK-TF7 - die uns die ersten Schritte während der Nutzung von Toshiba IK-TF7 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Toshiba IK-TF7 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Toshiba IK-TF7 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Toshiba IK-TF7?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Toshiba IK-TF7 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Toshiba IK-TF7 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)