Bedienungsanleitung Hobart LT1 ML-104239

16 Seiten 1.38 mb
Download

Zur Seite of 16

Summary
  • Hobart LT1 ML-104239 - page 1

    EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 FORM 18580 Rev. A (8-96) LO W TEMP DISHW ASHER MODEL LT1 ML-104239 LT1 DISHWASHER N S T R U C T I O N S I ...

  • Hobart LT1 ML-104239 - page 2

    – 2 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Hobart LT1 ML-104239 - page 3

    – 3 – Installation, Operation and Care of Model L T1 DISHW ASHER SA VE THESE INSTR UCTIONS GENERAL The Model LT1 Dishwasher is a low temperature (140 ° F recommended, 120 ° F minimum), chemical sanitizing, rack-type dishwasher for use with accessory 20" x 20" racks. It is equipped with a 3 ⁄ 4 horsepower thermally protected (inter ...

  • Hobart LT1 ML-104239 - page 4

    – 4 – PL-40920-1 FRONT RACK TRACK AND SPLASH GUARD SCREWS INST ALLA TION UNPACKING Immediately after unpacking the dishwasher, check it for possible shipping damage. If this machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, verify that the electrical service ag ...

  • Hobart LT1 ML-104239 - page 5

    – 5 – Installation Drawing — 436254 ...

  • Hobart LT1 ML-104239 - page 6

    – 6 – DISH TABLES Dish table end should be turned down and fitted over the lip of the dishwasher tank (Fig. 4). Use an NSF approved sealer between table and tank lip to prevent leaks. Fasten tables to the tank lip; truss head screws (by others) are recommended. PLUMBING CONNECTIONS Fig. 4 WARNING : PLUMBING CONNECTIONS MUST COMPLY WITH APPLICAB ...

  • Hobart LT1 ML-104239 - page 7

    – 7 – ELECTRICAL CONNECTION WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT. ELECTRICAL DATA Model Volt ...

  • Hobart LT1 ML-104239 - page 8

    – 8 – CYCLE TIMER ADJUSTMENT The cycle timer, which regulates the dishwasher cycle, may require adjustment in order to suit local conditions. To gain access to the cycle timer, loosen the bottom screw on the access cover located on the right side of the control box and rotate the access cover up (Fig. 9). Fig. 9 Fig. 10 The cycle timer (Fig. 9) ...

  • Hobart LT1 ML-104239 - page 9

    – 9 – OPERA TION CAUTION: Items made of pewter, aluminum, and silver will be attacked by the sodium hypochlorite sanitizing agent (liquid bleach) used in this machine and therefore should not be washed in it. In addition to these detailed instructions, brief instructions for operation and cleaning can be found on the front of the control box. C ...

  • Hobart LT1 ML-104239 - page 10

    – 10 – MACHINE PREPARATION Check to make sure that the pump intake strainer (Fig. 12), the drain pan strainer (Fig. 13), and the drain tube (Fig. 17) are in place and that both strainers are free of debris. The pump intake strainer must drop completely to the bottom of the sump. THE DRAIN AND STRAINERS MUST BE CLEAN AND FREE OF DEBRIS AT ALL TI ...

  • Hobart LT1 ML-104239 - page 11

    – 11 – DISHWASHING Scrape and/or rinse dishes to remove food particles and other debris. Never use steel wool on ware to be loaded into the dishwasher. Place the dishes in a rack. Do not stack dishes on top of each other as water must have free access to all sides of every dish. Stand plates edgewise in a peg-type rack (Fig. 16). Place cups, gl ...

  • Hobart LT1 ML-104239 - page 12

    – 12 – CLEANING THE DISHWASHER Clean the dishwasher after each working shift. Never use steel wool to clean warewasher surfaces. Use only products formulated to be safe on stainless steel. 1. Drain machine. Turn the P OWER switch Off. 2. Thoroughly cleanse and flush the dishwasher interior and then drain any water that may have accumulated. Wip ...

  • Hobart LT1 ML-104239 - page 13

    – 13 – DOs AND DON'Ts FOR YOUR NEW HOBART WAREWASHER DO assure proper water hardness. DO pre-scrap dishes thoroughly. DO use only detergents recommended by your chemical professional. DO at the end of the day, thoroughly cleanse the machine, rinse, and dry (leave door open). DO closely follow your chemical professional's prescribed de ...

  • Hobart LT1 ML-104239 - page 14

    – 14 – MAINTENANCE DELIMING WARNING : DELIMING SOLUTION MUST NOT COME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED IN THIS MACHINE. MIXING MAY CAUSE HAZARDOUS GAS TO FORM. THIS ENTIRE PROCEDURE MUST BE FOLLOWED STEP-BY-STEP FOR SAFE AND SATISFACTORY RESULTS. The dishwasher should be delimed when needed. Frequency of deliming ...

  • Hobart LT1 ML-104239 - page 15

    – 15 – 13. Run machine without loading dishware for two complete cycles to remove the chemical deliming agent. 14. Reconnect sanitizer, detergent, and rinse aid systems. 15. With the standpipes installed in their respective containers (red in detergent, white in sanitizer, blue in rinse aid), press and hold each pump priming switch until the co ...

  • Hobart LT1 ML-104239 - page 16

    – 16 – TROUBLESHOOTING Symptoms that persist after possible causes have been checked may require service. SYMPTOMS POSSIBLE CAUSES No Machine Operation 1. Machine POWER switch in the OFF position. 2. Blown fuse or tripped circuit breaker at power supply. 3. DELIME/NORMAL switch in the DELIME position and machine in the middle of a cycle. Contin ...

Produzent Hobart Kategorie Dishwasher

Dokumente, die wir vom Produzenten des Geräts Hobart LT1 ML-104239 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Hobart
- Bedienungsanleitungen LT1 ML-104239
- Produktkarten Hobart
- Informationsbroschüren
- oder Energieetiketten Hobart LT1 ML-104239
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Hobart LT1 ML-104239.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Hobart LT1 ML-104239, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Hobart LT1 ML-104239. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Hobart LT1 ML-104239 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Hobart LT1 ML-104239, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Hobart LT1 ML-104239 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Hobart LT1 ML-104239 verständlich ist.

Eine gänzliche Bedienungsanleitung von Hobart sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Hobart LT1 ML-104239 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Hobart LT1 ML-104239 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Hobart LT1 ML-104239, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Hobart LT1 ML-104239 - die uns die ersten Schritte während der Nutzung von Hobart LT1 ML-104239 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Hobart LT1 ML-104239 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Hobart LT1 ML-104239 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Hobart LT1 ML-104239?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Hobart LT1 ML-104239 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Hobart LT1 ML-104239 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)